Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because of some board issues, we need to disable parallel detect on
an HP blade.  Without this patch, the link state can become stuck
when it goes into parallel detect mode.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous patches to workaround the 5706S on an HP blade were not
sufficient.  The link state still does not change properly in some
cases.  This patch adds polling to make it completely reliable.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-3.4.4 on powerpc:

drivers/net/bnx2.c:67: error: version causes a section type conflict

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.

Problem was discovered by Roel Kluin <12o3l@tiscali.nl>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the programmable high/low water marks in 5709 for
802.3 flow control.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CTX_WR macro is unnecessary and obfuscates the code.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code.  Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the tx coalescing setup code independent of the MSIX vector.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix "bnx2->flags" names with BNX2_* for consistency.

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts.  We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.

The parallel detect logic is cleaned up slightly to better integrate
the workaround.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct.  It happens that they are the same in this
case because we are using the first MSIX vector.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The chip has problem running in this mode and needs to be disabled.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change bnx2_init_napi() to void.

Warning was noted by DaveM.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring.  Enable MSIX when the hardware supports it.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring.  The original tx ring will still be used
when not using MSIX.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change bnx2_napi struct into an array and add code to manage multiple
IRQs.  MSIX hardware structures and new registers are also added.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct.  Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.

Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes the code cleaner and easier to support different tx rings.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring.  This will guarantee order-0
allocation regardless of the MTU size.

Fixup loopback test packet size so that we don't deal with the pages
during loopback test.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.

Change the copybreak constant RX_COPY_THRESH to 128.  This same
constant will be used for the max. size of the linear SKB when pages
are used.  Copybreak will be turned off when pages are used.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new function to handle new SKB allocation and to prepare the
completed SKB.  This makes it easier to add support for non-linear
SKB.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define the various ring constants to make the code cleaner.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int().  We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.

The fix is to not store this latest hw index and only store the
processed rx index.  We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

5709 Ax and Bx chips all need this workaround.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>