The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Supported calibrations of radio retention table (RTT) are
	- DC offset
	- Filter
	- Peak detect

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To improve sensitivity for AR9480, the normal and minimum
noise floor values of both bands are updated.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.

This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The 5G Tx gain table w/ XPA is updated to improve spur
performance in high_power Tx gain table.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ar9003 table is updated to increase XLNA BIAS
output driver strengh.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Prevents lots of broken frames from showing up on monitor interfaces
by default.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code
to only report key miss errors if a MIC error wasn't reported.
When checking the flags in that order in the MAC code, it might miss some
real events, because the value of the MIC error flag is undefined under
some conditions.

The primary issue addressed by the previous commit is making sure that
MIC errors are properly reported on the STA side. This can be fixed in
a better way by adding a separate rx status flag for key miss and
ignoring it for multicast frames.

This fix slightly improves stability in AP mode on some older hardware,
like AR9132.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was previously used for current_rd_ext

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is unused since the previous dead code that was using it had been
removed earlier.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.

This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Export how many times each of the reset triggers has fired through debugfs.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory.  Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets

Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.

The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
	ops.conf_tx = conf_tx_op;

@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
	conf_tx_op (
-		struct ieee80211_hw *hw,
+		struct ieee80211_hw *hw, struct ieee80211_vif *vif,
		u16 queue,
		const struct ieee80211_tx_queue_params *params) {...}

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.

Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.

For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.

ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.

Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.

Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

proper dma_unmapping and freeing of skb's has to be done in the rx
cleanup for EDMA chipsets when the device is unloaded and this also
seems to address the following warning which shows up occasionally when
the device is unloaded

	Call Trace:
	[<c0148cd2>] warn_slowpath_common+0x72/0xa0
	[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
	[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
	[<c0148da3>] warn_slowpath_fmt+0x33/0x40
	[<c03b669c>] dma_debug_device_change+0x19c/0x200
	[<c0657f12>] notifier_call_chain+0x82/0xb0
	[<c0171370>] __blocking_notifier_call_chain+0x60/0x90
	[<c01713bf>] blocking_notifier_call_chain+0x1f/0x30
	[<c044f594>] __device_release_driver+0xa4/0xc0
	[<c044f647>] driver_detach+0x97/0xa0
	[<c044e65c>] bus_remove_driver+0x6c/0xe0
	[<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60
	[<c0450109>] driver_unregister+0x49/0x80
	[<c0299f54>] ? sysfs_remove_file+0x14/0x20
	[<c03c3ab2>] pci_unregister_driver+0x32/0x80
	[<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k]
	[<f92c8467>] ath9k_exit+0x17/0x36 [ath9k]
	[<c06523cd>] ? mutex_unlock+0xd/0x10
	[<c018e27f>] sys_delete_module+0x13f/0x200
	[<c02139bb>] ? sys_munmap+0x4b/0x60
	[<c06547c5>] ? restore_all+0xf/0xf
	[<c0657a20>] ? spurious_fault+0xe0/0xe0
	[<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180
	[<c065b863>] sysenter_do_call+0x12/0x38
	 ---[ end trace 16e1c1521c06bcf9 ]---
	Mapped at:
	[<c03b7938>] debug_dma_map_page+0x48/0x120
	[<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k]
	[<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k]
	[<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k]

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>