Select Git revision
Search by author
- Any Author
- authors
-
Abhiram Balasubramanian abhiram
-
Anton Burtsev
aburtsev
-
Charlie Jacobsen cjacobsen
-
David Detweiler ddetweiler
-
David Johnson johnsond
-
Michael Quigley MichaelQuigley
-
Mike Hibler hibler
-
Robert Ricci ricci
-
Sarah Spall spall
-
Scotty Bauer ScottyB
-
Vikram Narayanan vikram
- Apr 14, 2011
-
-
Yogesh Ashok Powar authored
The return statement at the last line of a void function is not necessary. Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
1) remove mwifiex_alloc_fill_wait_queue() and mwifiex_request_ioctl() 2) avoid dynamic allocation of wait queue 3) remove unnecessary mwifiex_error_code macros that were used mainly by the wait queue status code 4) remove some abstraction functions 5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async() and mwifiex_send_sync() to handle asynchronous and synchronous commands respectively Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Felix Fietkau authored
There are two variants of AR5312 dual-band devices, one single-radio and the other one dual-radio. On the dual-radio board, the first MAC only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz part of this phy is used in pass-through mode, connecting the second MAC with the second PHY. Disable 2.4 GHz for the first MAC on an AR5312, but only if the board configuration indicates a dual-radio device. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Tested-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
-
Felix Fietkau authored
EEPROM version 5.0 adds a new field for disabling AES support, having an older version means that AES is present. This patch fixes hw AES crypto support on AR5312 boards, which have an older EEPROM version. Signed-off-by:
-
Felix Fietkau authored
On AHB, the calibration data usually does not contain a valid MAC address, the correct MAC address is stored in the board config. Signed-off-by:
-
Felix Fietkau authored
This struct is not used in any common code, and moving it out of the ath header makes it easier to add more driver specific ops. Signed-off-by:
-
Felix Fietkau authored
On a dual-radio dual-band AR5312 device, the calibration data is shared between the 5 GHz and the 2.4 GHz radio/MAC. Signed-off-by:
-
Rajkumar Manoharan authored
Request a re-configuration of Beacon related timers on the receipt of the first Beacon frame has to be set only for station mode. Setting beacon sync for IBSS is causing wrong beacon slot selection on beacon generation. Signed-off-by:
Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by:
-
John W. Linville authored
Otherwise, you get this: CC [M] drivers/net/wireless/ath/ath9k/hif_usb.o drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’: drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’ make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1 make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2 make: *** [drivers/net/wireless/ath/] Error 2 The TX_STAT_INC macro should probably be changed to accomodate such usage, although using a trinary operator in place of an if-else seems questionable to me anyway. Signed-off-by:
Sujith Manoharan <Sujith.Manoharan@Atheros.com>
-
- Apr 13, 2011
-
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
New debugfs files: <debugfs_root>/ath9k_htc/<phy#>/tgt_int_stats <debugfs_root>/ath9k_htc/<phy#>/tgt_tx_stats <debugfs_root>/ath9k_htc/<phy#>/tgt_rx_stats Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Beacon transmission needs to involve as little latency as possible after receiving a SWBA event from the target. Since packets are buffered to use TX stream mode, beacon frames sometimes gets queued up and are not sent out immediately. Fix this by decoupling management frame transmission from the normal data path and send them out immediately. Signed-off-by:
-
Sujith Manoharan authored
Occasionally, a WMI event would arrive ahead of the TX URB completion handler. Discarding these events would exhaust the available TX slots, so handle them by running a timer cleaning up such events. Also, timeout packets for which TX completion events have not arrived. Signed-off-by:
-
Sujith Manoharan authored
Location: ath9k_htc/phy#/queue Signed-off-by:
-
Sujith Manoharan authored
Location: ath9k_htc/phy#/slot Signed-off-by:
-
Sujith Manoharan authored
Now that the infrastructure is in place, process WMI TX status events and complete packets. Signed-off-by:
-
Sujith Manoharan authored
When a station entry is removed, there could still be pending packets destined for that station in the HIF layer. Sending these to the target is not necessary, so drain them in the driver itself. Signed-off-by:
-
Sujith Manoharan authored
There is no point in looping over all the endpoints, since the HIF layer uses the start/stop APIs only for the TX pipe. Simplify the API accordingly. Signed-off-by:
-
Sujith Manoharan authored
When doing a channel set or a reset operation the pending frames queued up for transmission have to be flushed and sent to mac80211. Fixing this has to be done in two separate steps: * Flush queued frames and kill the URB TX completion handler. * Complete all the frames that in the TX pending queue. This patch adds proper support for draining and all the callsites namely, channel change/reset/idle/stop are fixed. A separate queue is used for handling failed frames. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Maintain a bitmap of slots for transmission and update the cookie field for every packet with the slot value. This value would be used for matching packets when TX completion processing is added. Signed-off-by:
-
Sujith Manoharan authored
There is no need to do endpoint header removal in the ISR. Also, this is needed when TX slot management is added later on. Use a helper function to strip the driver header. Signed-off-by:
-
Sujith Manoharan authored
A new routine that takes an endpoint explicitly is introduced. The normal htc_send() now retrieves the endpoint from the packet's private data. This would be useful in TX completion when the endpoint ID would be required. While at it, use a helper function to map the queue to endpoint. Data/mgmt/beacon packets use htc_send(), while WMI comamnds pass the endpoint to HTC. Signed-off-by:
-
Sujith Manoharan authored
Handle queue start/stop properly by maintaining a counter to check if the pending frame count has exceeded the threshold. Otherwise, packets would be dropped needlessly. While at it, use a simple flag to track queue status and use helper functions too. Signed-off-by:
-
Sujith Manoharan authored
Using a single URB for receiving WMI events is insufficient, increase it to 64 to not lose WMI events in high throughput situations. Signed-off-by:
-
Sujith Manoharan authored
This event will be generated by the target for packet completions. Signed-off-by:
-
Sujith Manoharan authored
Add a new cookie field that would be filled by the host. This can be used to match the TX status WMI event with the appropriate packet. Signed-off-by:
-
Sujith Manoharan authored
The current max queue length of 1024 is quite large and unnecessary. 256 suffices well enough even for high throughput situations. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
For all packets sent through the USB_WLAN_TX_PIPE endpoint, the private area of the SKB's tx_info can be used to store driver-specific information. For packets sent through USB_REG_OUT_PIPE, this will not make a difference since they are routed through a separate routine that doesn't access the private region. This would help in situations where TX information is required in the URB callback. Signed-off-by:
-
Sujith Manoharan authored
WMI_TGT_TXQ_ENABLE_CMDID WMI_HOST_ATTACH WMI_DEBUG_INFO_CMDID WMI_BEACON_UPDATE_CMDID WMI_RESET_CMDID WMI_RX_LINK_CMDID WMI_STOP_DMA_RECV_CMDID Signed-off-by:
-
Sujith Manoharan authored
The length of the received SKB could be equal to HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors, in which case they are dropped without being processed. Fix this check so that the error counters are updated correctly. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Use a queue to handle WMI events and schedule a tasklet to process the events. This fixes the race between the WMI event ISR and the SWBA tasklet when the arrival of WMI events in quick succession could overwrite the SWBA data before the tasklet from a previous iteration could have been scheduled. Also, drain the WMI queue properly. Signed-off-by:
-
