Kconfig

	 configuring PPTP clients and servers to utilize this method.

config PPPOE
	tristate "PPP over Ethernet (EXPERIMENTAL)"
	depends on EXPERIMENTAL && PPP
	help
	  Support for PPP over Ethernet.

	  This driver requires the latest version of pppd from the CVS
	  repository at cvs.samba.org.  Alternatively, see the 
	  RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
	  which contains instruction on how to use this driver (under 
	  the heading "Kernel mode PPPoE").

config PPPOATM
	tristate "PPP over ATM"
	depends on ATM && PPP
	help
	  Support PPP (Point to Point Protocol) encapsulated in ATM frames.
	  This implementation does not yet comply with section 8 of RFC2364,
	  which can lead to bad results if the ATM peer loses state and
	  changes its encapsulation unilaterally.

config PPPOL2TP
	tristate "PPP over L2TP (EXPERIMENTAL)"
	depends on EXPERIMENTAL && PPP && INET
	help
	  Support for PPP-over-L2TP socket family. L2TP is a protocol
	  used by ISPs and enterprises to tunnel PPP traffic over UDP
	  tunnels. L2TP is replacing PPTP for VPN uses.

	  This kernel component handles only L2TP data packets: a
	  userland daemon handles L2TP the control protocol (tunnel
	  and session setup). One such daemon is OpenL2TP
	  (http://openl2tp.sourceforge.net/).

config SLIP
	tristate "SLIP (serial line) support"
	---help---
	  Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
	  connect to your Internet service provider or to connect to some
	  other local Unix box or if you want to configure your Linux box as a
	  Slip/CSlip server for other people to dial in. SLIP (Serial Line
	  Internet Protocol) is a protocol used to send Internet traffic over
	  serial connections such as telephone lines or null modem cables;
	  nowadays, the protocol PPP is more commonly used for this same
	  purpose.

	  Normally, your access provider has to support SLIP in order for you
	  to be able to use it, but there is now a SLIP emulator called SLiRP
	  around (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection. If
	  you plan to use SLiRP, make sure to say Y to CSLIP, below. The
	  NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, explains how to
	  configure SLIP. Note that you don't need this option if you just
	  want to run term (term is a program which gives you almost full
	  Internet connectivity if you have a regular dial up shell account on
	  some Internet connected Unix computer. Read
	  <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
	  support will enlarge your kernel by about 4 KB. If unsure, say N.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module will be
	  called slip.

config SLIP_COMPRESSED
	bool "CSLIP compressed headers"
	depends on SLIP
	select SLHC
	---help---
	  This protocol is faster than SLIP because it uses compression on the
	  TCP/IP headers (not on the data itself), but it has to be supported
	  on both ends. Ask your access provider if you are not sure and
	  answer Y, just in case. You will still be able to use plain SLIP. If
	  you plan to use SLiRP, the SLIP emulator (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection, you
	  definitely want to say Y here. The NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, explains how to configure
	  CSLIP. This won't enlarge your kernel.

config SLHC
	tristate
	help
	  This option enables Van Jacobsen serial line header compression
	  routines.

config SLIP_SMART
	bool "Keepalive and linefill"
	depends on SLIP
	help
	  Adds additional capabilities to the SLIP driver to support the
	  RELCOM line fill and keepalive monitoring. Ideal on poor quality
	  analogue lines.

config SLIP_MODE_SLIP6
	bool "Six bit SLIP encapsulation"
	depends on SLIP
	help
	  Just occasionally you may need to run IP over hostile serial
	  networks that don't pass all control characters or are only seven
	  bit. Saying Y here adds an extra mode you can use with SLIP:
	  "slip6". In this mode, SLIP will only send normal ASCII symbols over
	  the serial device. Naturally, this has to be supported at the other
	  end of the link as well. It's good enough, for example, to run IP
	  over the async ports of a Camtec JNT Pad. If unsure, say N.

config NET_FC
	bool "Fibre Channel driver support"
	depends on SCSI && PCI
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config SHAPER
	tristate "Traffic Shaper (OBSOLETE)"
	depends on EXPERIMENTAL
	---help---
	  The traffic shaper is a virtual network device that allows you to
	  limit the rate of outgoing data flow over some other network device.
	  The traffic that you want to slow down can then be routed through
	  these virtual devices. See
	  <file:Documentation/networking/shaper.txt> for more information.

	  An alternative to this traffic shaper are traffic schedulers which
	  you'll get if you say Y to "QoS and/or fair queuing" in
	  "Networking options".

	  To compile this driver as a module, choose M here: the module
	  will be called shaper.  If unsure, say N.

config NETCONSOLE
	tristate "Network console logging support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	If you want to log kernel messages over the network, enable this.
	See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
	bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
	depends on NETCONSOLE && SYSFS && EXPERIMENTAL
	select CONFIGFS_FS
	help
	  This option enables the ability to dynamically reconfigure target
	  parameters (interface, IP addresses, port numbers, MAC addresses)
	  at runtime through a userspace interface exported using configfs.
	  See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
	def_bool NETCONSOLE

config NETPOLL_TRAP
	bool "Netpoll traffic trapping"
	default n
	depends on NETPOLL

config NET_POLL_CONTROLLER
	def_bool NETPOLL

endif # NETDEVICES