Now that none of the drivers use CONFIG_MTD_PARTITIONS we can remove
it from Kconfig and the last remaining uses.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add a driver for allowing an mtd device to be used as a block device for
swapping. The block device is volatile, and the mapping of swapped pages
is not stored on flash.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Move mtdconcat to be an integral part of the mtd core. It's a tiny bit
of code, which bears 'say Y if you don't know what to do' note in the
Kconfig. OTOH there are several ugly ifdefs depending on the MTD_CONCAT.
So, making MTD_CONCAT support mandatory will allow us to clean up code a
lot.

Kconfig entry is changed to be a bool defaulting to Y, so all code
pieces depending on it, will have MTD_CONCAT Kconfig symbol and
CONFIG_MTD_CONCAT define. This will be removed in one of next patches.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

MTD_OF_PARTS should be possible on all architectures, not just
powerpc and microblaze, and it probably should not be a user
selectable option.  Neither does it need to be in a separate module.

Also, rework MTD Kconfig to group options dependant on MTD_PARTITIONS
into a if/endif block.  Do the same for MTD_REDBOOT_PARTS.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Removes one .h and one .c file that are never used outside of
mtdcore.c.

Signed-off-by: Joern Engel <joern@logfs.org>

Edited to remove on leftover debug define.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

This implements new readwrite SmartMedia/xd FTL.

mtd driver must have support proper ECC and badblock verification
based on oob parts for 512 bytes nand.

Also mtd driver must define read_oob and write_oob, which are used
to read and write both data and oob together.

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Present backing device capabilities for MTD character device files to allow
NOMMU mmap to do direct mapping where possible.

Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We have two components to manage LPDDR flash memories in Linux.
1. It is a driver for chip probing and reading its capabilities
2. It is a device operations driver.

Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add MTD tests to Kconfig and Makefiles.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We want drivers/mtd/{mtdcore, mtdsuper, mtdpart}.c to be built and linked
into the same mtd.ko module. Fix the Makefile to ensure this, and remove
duplicate MODULE_ declarations in mtdpart.c, as mtdcore.c already has them.

Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Kernel oops and panic messages are invaluable when debugging crashes.
These messages often don't make it to flash based logging methods (say a
syslog on jffs2) due to the overheads involved in writing to flash.

This patch allows you to turn an MTD partition into a circular log
buffer where kernel oops and panic messages are written to. The messages
are obtained by registering a console driver and checking
oops_in_progress. Erases are performed in advance to maximise the
chances of a saving messages.

To activate it, add console=ttyMTDx to the kernel commandline (where x
is the mtd device number to use).

Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Generalise the handling of MTD-specific superblocks so that JFFS2 and ROMFS
can both share it.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

UBI (Latin: "where?") manages multiple logical volumes on a single
flash device, specifically supporting NAND flash devices. UBI provides
a flexible partitioning concept which still allows for wear-levelling
across the whole flash device.

In a sense, UBI may be compared to the Logical Volume Manager
(LVM). Whereas LVM maps logical sector numbers to physical HDD sector
numbers, UBI maps logical eraseblocks to physical eraseblocks.

More information may be found at
http://www.linux-mtd.infradead.org/doc/ubi.html



Partitioning/Re-partitioning

  An UBI volume occupies a certain number of erase blocks. This is
  limited by a configured maximum volume size, which could also be
  viewed as the partition size. Each individual UBI volume's size can
  be changed independently of the other UBI volumes, provided that the
  sum of all volume sizes doesn't exceed a certain limit.

  UBI supports dynamic volumes and static volumes. Static volumes are
  read-only and their contents are protected by CRC check sums.

Bad eraseblocks handling

  UBI transparently handles bad eraseblocks. When a physical
  eraseblock becomes bad, it is substituted by a good physical
  eraseblock, and the user does not even notice this.

Scrubbing

  On a NAND flash bit flips can occur on any write operation,
  sometimes also on read. If bit flips persist on the device, at first
  they can still be corrected by ECC, but once they accumulate,
  correction will become impossible. Thus it is best to actively scrub
  the affected eraseblock, by first copying it to a free eraseblock
  and then erasing the original. The UBI layer performs this type of
  scrubbing under the covers, transparently to the UBI volume users.

Erase Counts

  UBI maintains an erase count header per eraseblock. This frees
  higher-level layers (like file systems) from doing this and allows
  for centralized erase count management instead. The erase counts are
  used by the wear-levelling algorithm in the UBI layer. The algorithm
  itself is exchangeable.

Booting from NAND

  For booting directly from NAND flash the hardware must at least be
  capable of fetching and executing a small portion of the NAND
  flash. Some NAND flash controllers have this kind of support. They
  usually limit the window to a few kilobytes in erase block 0. This
  "initial program loader" (IPL) must then contain sufficient logic to
  load and execute the next boot phase.

  Due to bad eraseblocks, which may be randomly scattered over the
  flash device, it is problematic to store the "secondary program
  loader" (SPL) statically. Also, due to bit-flips it may become
  corrupted over time. UBI allows to solve this problem gracefully by
  storing the SPL in a small static UBI volume.

UBI volumes vs. static partitions

  UBI volumes are still very similar to static MTD partitions:

    * both consist of eraseblocks (logical eraseblocks in case of UBI
      volumes, and physical eraseblocks in case of static partitions;
    * both support three basic operations - read, write, erase.

  But UBI volumes have the following advantages over traditional
  static MTD partitions:

    * there are no eraseblock wear-leveling constraints in case of UBI
      volumes, so the user should not care about this;
    * there are no bit-flips and bad eraseblocks in case of UBI volumes.

  So, UBI volumes may be considered as flash devices with relaxed
  restrictions.

Where can it be found?

  Documentation, kernel code and applications can be found in the MTD
  gits.

What are the applications for?

  The applications help to create binary flash images for two purposes: pfi
  files (partial flash images) for in-system update of UBI volumes, and plain
  binary images, with or without OOB data in case of NAND, for a manufacturing
  step. Furthermore some tools are/and will be created that allow flash content
  analysis after a system has crashed..

Who did UBI?

  The original ideas, where UBI is based on, were developed by Andreas
  Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others
  were involved too. The implementation of the kernel layer was done by Artem
  B. Bityutskiy. The user-space applications and tools were written by Oliver
  Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem.
  Joern Engel contributed a patch which modifies JFFS2 so that it can be run on
  a UBI volume. Thomas Gleixner did modifications to the NAND layer. Alexander
  Schmidt made some testing work as well as core functionality improvements.

Signed-off-by: Artem B. Bityutskiy <dedekind@linutronix.de>
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>

Add a MTD_BLKDEVS Kconfig option to cleanup the makefile a bit

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>

Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

OneNAND is a new flash technology from Samsung with integrated SRAM
buffers and logic interface.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

This type of flash translation layer (FTL) is used by the Embedded BIOS
by General Software. It is known as the Resident Flash Disk (RFD), see:

http://www.gensw.com/pages/prod/bios/rfd.htm



Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!