If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit.  Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.

The fix is pretty straightforward.  This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt.  If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.

Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function netxen_intr has pointer to nx_host_sds_ring
as second parameter not pointer to netxen_adapter.

Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Bruce Allan <bruce.w.allan@intel.com>

The alternate MAC address feature is only supported by 80003ES2LAN and
82571 LOMs as well as a couple 82571 mezzanine cards.  Checking for an
alternate MAC address on other parts can fail leading to the driver not
able to load.  This patch limits the check for an alternate MAC address
to be done only for parts that support the feature.

This issue has been around since support for the feature was introduced
to the e1000e driver in 2.6.34.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Fabio Varesano <fax8@users.sourceforge.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the e1000-devel mailing list, Nils Faerber reported latency issues with
the 82573 LOM on a ThinkPad X60.  It was found to be caused by ASPM L1;
disabling it resolves the latency.  The issue is present in kernels back
to 2.6.34 and possibly 2.6.33.


Reported-by: Nils Faerber <nils.faerber@kernelconcepts.de>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Functions ll_temac_rx_irq and ll_temac_tx_irq
have pointer to net_device as second parameter not
pointer to temac_local.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the following opps which can occur when trying to deallocate
receive buffer pools when changing the MTU of an active ibmveth device.

Oops: Kernel access of bad area, sig: 11 [#1]
NIP: d000000004db00e8 LR: d000000004db00ac CTR: 0000000000591038
REGS: c00000007fff39d0 TRAP: 0300   Not tainted  (2.6.36-rc1)
MSR: 8000000000009032 <EE,ME,IR,DR>  CR: 22248244  XER: 00000002
DAR: 0000000000000488, DSISR: 0000000042000000
TASK = c00000007c463790[6531] 'netserver' THREAD: c00000007a154000 CPU: 0
GPR00: 0000000000000000 c00000007fff3c50 d000000004dbd360 0000000000000001
GPR04: 0000000000000001 1fffffffffffffff 000000000000043c c00000007a8e9f60
GPR08: c00000007a8e9e20 0000000000000245 0000000000000488 0000000000000000
GPR12: 00000000000000c0 c000000006d70000 c00000007bfec098 c00000007bfebc2c
GPR16: c00000007a157c78 0000000000000000 0000000000000001 0000000000000000
GPR20: 0000000000000001 0000000000000010 c000000000b51180 c00000007a8e9d90
GPR24: c00000007a8e9da0 c00000007a8e9580 00000000000005ea 00000000000002ff
GPR28: 0000000000000004 0000000000000080 c000000000a946f8 c00000007a8e9d80
NIP [d000000004db00e8] .ibmveth_remove_buffer_from_pool+0xe8/0x130 [ibmveth]
LR [d000000004db00ac] .ibmveth_remove_buffer_from_pool+0xac/0x130 [ibmveth]
Call Trace:
[c00000007fff3c50] [d000000004db00ac] .ibmveth_remove_buffer_from_pool+0xac/0x130 [ibmveth] (unreliable)
[c00000007fff3cf0] [d000000004db31dc] .ibmveth_poll+0x30c/0x460 [ibmveth]
[c00000007fff3dd0] [c00000000042c4b8] .net_rx_action+0x178/0x278
[c00000007fff3eb0] [c000000000093cf0] .__do_softirq+0x118/0x1f8
[c00000007fff3f90] [c00000000002ab3c] .call_do_softirq+0x14/0x24
[c00000007a157600] [c00000000000e3e4] .do_softirq+0xec/0x110
[c00000007a1576a0] [c000000000093394] .local_bh_enable_ip+0xb4/0xe0
[c00000007a157720] [c0000000004f0bac] ._raw_spin_unlock_bh+0x3c/0x50
[c00000007a157790] [c0000000004186e0] .release_sock+0x158/0x188
[c00000007a157840] [c000000000479660] .tcp_recvmsg+0x560/0x9b8
[c00000007a157970] [c0000000004a0d78] .inet_recvmsg+0x80/0xd8
[c00000007a157a00] [c000000000413e28] .sock_recvmsg+0x128/0x178
[c00000007a157bf0] [c0000000004164ac] .SyS_recvfrom+0xb4/0x148
[c00000007a157d70] [c000000000411f3c] .SyS_socketcall+0x274/0x360
[c00000007a157e30] [c0000000000085b4] syscall_exit+0x0/0x40

Reported-by: Rafael Camarda Silva Folco <rfolco@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: Fix synchronization between HW and SW send queue

When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.

This patch detects such loss of synchronization, and resets the ehea
port when needed.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update bnx2x version to 1.52.53-4

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sachin Sanap <ssanap@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For 5000 series of devices, use long monitor timer to check
stuck tx queues.

This modification apply to all the 5000 series including 5300 and others.

Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit c96c31e4
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case.  Restore the original case.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Applying the filter flags directly as done since

commit 3474ad63
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke 3945 under some unknown circumstances, as
reported by Alex.

Since I want to keep the direct application of
filter flags on iwlagn, duplicate the code into
both 3945 and agn and remove committing the
RXON that broke things from the 3945 version.

Cc: stable@kernel.org [2.6.35]
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are allocated with pci_alloc_consistent, so calling
pci_dma_sync_single_for_cpu is incorrect usage of the API.  Remove this
misuse and consequently avoid the following backtrace:

WARNING: at lib/dma-debug.c:902 check_sync+0xce/0x43a()
Hardware name: 2373HU6
ipw2100 0000:02:02.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x0000000034e88008] [size=8 bytes]
Modules linked in: microcode ipw2100(+) snd_seq_device ppdev libipw nsc_ircc snd_pcm lib80211 video output irda parport_pc cfg80211 parport thinkpad_acpi e1000 iTCO_wdt crc_ccitt snd_timer iTCO_vendor_support snd i2c_i801 pcspkr rfkill soundcore joydev snd_page_alloc yenta_socket radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Tainted: G        W   2.6.35-wl+ #8
Call Trace:
 [<c043aa42>] warn_slowpath_common+0x6a/0x7f
 [<c05d252a>] ? check_sync+0xce/0x43a
 [<c043aaca>] warn_slowpath_fmt+0x2b/0x2f
 [<c05d252a>] check_sync+0xce/0x43a
 [<c046189a>] ? print_lock_contention_bug+0x11/0xb2
 [<c05d2b6f>] debug_dma_sync_single_for_cpu+0x47/0x49
 [<c06cbd3c>] ? ehci_irq+0x31/0x331
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a221d>] pci_dma_sync_single_for_cpu.clone.1+0x42/0x4b [ipw2100]
 [<f82a23a2>] ipw2100_irq_tasklet+0x17c/0x5e9 [ipw2100]
 [<c043fd87>] tasklet_action+0x78/0xcb
 [<c0440293>] __do_softirq+0xc4/0x183
 [<c044038d>] do_softirq+0x3b/0x5f
 [<c04404d0>] irq_exit+0x3a/0x6d
 [<c0404423>] do_IRQ+0x8b/0x9f
 [<c04038b5>] common_interrupt+0x35/0x3c
 [<c062ecfa>] ? acpi_idle_enter_simple+0xfe/0x13c
 [<c045007b>] ? exit_itimers+0x2d/0x73
 [<c062ecfc>] ? acpi_idle_enter_simple+0x100/0x13c
 [<c070bf10>] cpuidle_idle_call+0x78/0xdc
 [<c040251c>] cpu_idle+0x9b/0xb7
 [<c07b1dd2>] rest_init+0xa6/0xab
 [<c0a4b96d>] start_kernel+0x389/0x38e
 [<c0a4b0c9>] i386_start_kernel+0xc9/0xd0

Signed-off-by: John W. Linville <linville@tuxdriver.com>

For 5000 and 6000g2b series of devices, use long monitor timer to check
stuck tx queues.

.6000g2b series device, it is WiFi/BT combo device, there are some cases,
tx queues are not move for a period of time because the WiFi/BT coex.

.5000 series device, it is being reported firmware got reload more
often than necessary, so extend the timer to avoid un-necessary reload.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change the name for monitor timer, also adding define for long monitor
timer; long monitor timer can be used for the type of devices require longer
time to determine the uCode is stuck on tx and needed reload.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.

It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.

Example of issues you'd see:

  - On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
    Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
    with ASPM enabled, the card will eventually stall on heavy traffic
    with often 'unsupported jumbo' warnings appearing. Disabling
    ASPM L0s in ath5k fixes these problems.

  - On the same card you would see a storm of RXORN interrupts
    even though medium is idle.

Credit for root causing and fixing the bug goes to Jussi Kivilinna.

Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch handles the firmware loading properly
for device ID 7015.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use appropriate command (CMD_TRIGGER_SCAN_TO) instead of scan command
(CMD_SCAN) to configure trigger scan timeout.

This was broken in commit 3a98c30f.

This fix address the bug reported here:

https://bugzilla.kernel.org/show_bug.cgi?id=16554



Cc: stable@kernel.org
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.

Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Several gigabit network drivers (SB1250_MAC, TIGON3, FSL, GIANFAR,
UCC_GETH, MV643XX_ETH, XILINX_LL_TEMAC, S6GMAC, STMMAC_ETH, PASEMI_MAC,
and OCTEON_ETHERNET) select PHYLIB.  These drivers are not under
NET_ETHERNET (10/100 mbit), so this warning is generated (long, irrelevant
parts are omitted):

warning: (NET_DSA && NET && EXPERIMENTAL && NET_ETHERNET && !S390 || ... || SB1250_MAC && NETDEVICES && NETDEV_1000 && SIBYTE_SB1xxx_SOC || TIGON3 && NETDEVICES && NETDEV_1000 && PCI || FSL_PQ_MDIO && NETDEVICES && NETDEV_1000 && FSL_SOC || GIANFAR && NETDEVICES && NETDEV_1000 && FSL_SOC || UCC_GETH && NETDEVICES && NETDEV_1000 && QUICC_ENGINE || MV643XX_ETH && NETDEVICES && NETDEV_1000 && (MV64X60 || PPC32 || PLAT_ORION) || XILINX_LL_TEMAC && NETDEVICES && NETDEV_1000 && (PPC || MICROBLAZE) || S6GMAC && NETDEVICES && NETDEV_1000 && XTENSA_VARIANT_S6000 || STMMAC_ETH && NETDEV_1000 && NETDEVICES && CPU_SUBTYPE_ST40 || PASEMI_MAC && NETDEVICES && NETDEV_10000 && PPC_PASEMI && PCI || OCTEON_ETHERNET && STAGING && !STAGING_EXCLUDE_BUILD && CPU_CAVIUM_OCTEON) selects PHYLIB which has unmet direct dependencies (!S390 && NET_ETHERNET)

PHYLIB is used by non-10/100 mbit ethernet drivers, so change the dependencies
to be NETDEVICES instead of NET_ETHERNET.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This should fix the oops which occurs during the packet injection
on monitor interface.

EIP is at ath9k_htc_tx_start+0x69/0x220 [ath9k_htc]
 [<f84dc8ea>] ? invoke_tx_handlers+0xa5a/0xee0 [mac80211]
 [<f82c84f4>] ? ath9k_htc_tx+0x44/0xe0 [ath9k_htc]
 [<f84db7b8>] ? __ieee80211_tx+0xf8/0x190 [mac80211]
 [<f84dce0d>] ? ieee80211_tx+0x9d/0x1a0 [mac80211]
 [<f84dcfac>] ? ieee80211_xmit+0x9c/0x1c0 [mac80211]
 [<f84dd1b5>] ? ieee80211_monitor_start_xmit+0x85/0xb0 [mac80211]
 [<c04c30cd>] ? dev_hard_start_xmit+0x1ad/0x210
 [<c04b97c2>] ? __alloc_skb+0x52/0x130
 [<c04d7cd5>] ? sch_direct_xmit+0x105/0x170
 [<c04c5e9f>] ? dev_queue_xmit+0x37f/0x4b0
 [<c0567e1e>] ? packet_snd+0x21e/0x250
 [<c05684a2>] ? packet_sendmsg+0x32/0x40
 [<c04b4c63>] ? sock_aio_write+0x113/0x130
 [<c0207934>] ? do_sync_write+0xc4/0x100
 [<c0167740>] ? autoremove_wake_function+0x0/0x50
 [<c02f4414>] ? security_file_permission+0x14/0x20
 [<c0207ad4>] ? rw_verify_area+0x64/0xe0
 [<c01e6458>] ? handle_mm_fault+0x338/0x390
 [<c0207cd5>] ? vfs_write+0x185/0x1a0
 [<c058db20>] ? do_page_fault+0x160/0x3a0
 [<c0208512>] ? sys_write+0x42/0x70
 [<c01033ec>] ? syscall_call+0x7/0xb

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is necessary to call pm_qos_add_request prior to calling
pm_qos_update_request.  It was revealed that ipw2100 has been
doing this wrong since "pm_qos: Get rid of the allocation in
pm_qos_add_request()" (commit 82f68251)
added a WARN that results in the following backtrace:

WARNING: at kernel/pm_qos_params.c:264 pm_qos_update_request+0x5e/0x70()
pm_qos_update_request() called for unknown object
Call Trace:
[<c1024088>] ? warn_slowpath_common+0x78/0xb0
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<c1024153>] ? warn_slowpath_fmt+0x33/0x40
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<f89fe15f>] ? ipw2100_up+0x3f/0xf10 [ipw2100]
[<c11961c9>] ? vsnprintf+0xc9/0x530
[<f89ff36c>] ? ipw2100_net_init+0x2c/0x1c0 [ipw2100]
[<c12f542d>] ? register_netdevice+0x7d/0x3c0
[<f89f9b00>] ? ipw2100_irq_tasklet+0x910/0x9a0 [ipw2100]
[<c12f579f>] ? register_netdev+0x2f/0x40
[<f89fd471>] ? ipw2100_pci_init_one+0xd21/0x1060 [ipw2100]
[<c11a5ebb>] ? local_pci_probe+0xb/0x10
[<c11a6d49>] ? pci_device_probe+0x69/0x90
[<c1224704>] ? driver_probe_device+0x74/0x180
[<c10dd15a>] ? sysfs_create_dir+0x6a/0xb0
[<c1224889>] ? __driver_attach+0x79/0x80
[<c1224810>] ? __driver_attach+0x0/0x80
[<c1223fa2>] ? bus_for_each_dev+0x52/0x80
[<c1224586>] ? driver_attach+0x16/0x20
[<c1224810>] ? __driver_attach+0x0/0x80
[<c122395f>] ? bus_add_driver+0x17f/0x250
[<c11a5ec0>] ? pci_device_shutdown+0x0/0x20
[<c11a6c80>] ? pci_device_remove+0x0/0x40
[<c1224b13>] ? driver_register+0x63/0x120
[<c11a6f96>] ? __pci_register_driver+0x36/0xa0
[<f84f9048>] ? ipw2100_init+0x48/0x67 [ipw2100]
[<c1001122>] ? do_one_initcall+0x32/0x170
[<c1087078>] ? __vunmap+0xb8/0xf0
[<f84f9000>] ? ipw2100_init+0x0/0x67 [ipw2100]
[<c10510c1>] ? sys_init_module+0x161/0x1000
[<c108f847>] ? sys_close+0x67/0xe0
[<c13647c1>] ? syscall_call+0x7/0xb

This patch moves pm_qos_add_request prior to pci_register_driver in
ipw2100 in order to avoid this problem.

Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The setting of SPI_DATA_POS depending on CONFIG_CAIF_SPI_SYNC
where inverted.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes rx_submit() return an error code, and makes some call sites
that care check the return value. This is important because it lets us properly
handle cases where the device isn't ready to handle URB submissions (e.g., when
it is autosuspended under some drivers); previously, we would attempt and fail
to submit URBs and reschedule ourselves to try and fail again. This patch is
against Linus's 2.6 repo commit 45d7f32c.

Signed-Off-By: Elizabeth Jones <ellyjones@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks.  I allocated them with kcalloc()
instead.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the original code we allocated memory conditionally and freed it in
the error handling unconditionally.  It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function.  I
removed those checks.

Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix phy.c kernel-doc notation:

Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/wan/farsync.c: In function 'fst_intr_rx':
drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size
drivers/net/wan/farsync.c: In function 'do_bottom_half_tx':
drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size

The "skb" and "mem" arguments being passed here are DMA addresses
being programmed into the hardware registers, so pass them as the type
that they actually are.  And use the correct printf formatting in
debug logging statements for these things to match the type change.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the driver will try to protect all frames,
which leads to a lot of odd things like sending an
RTS with a zeroed RA before multicast frames, which
is clearly bogus.

In order to fix all of this, we need to take a step
back and see what we need to achieve:
 * we need RTS/CTS protection if requested by
   the AP for the BSS, mac80211 tells us this
 * in that case, CTS-to-self should only be
   enabled when mac80211 tells us
 * additionally, as a hardware workaround, on
   some devices we have to protect aggregated
   frames with RTS

To achieve the first two items, set up the RXON
accordingly and set the protection required flag
in the transmit command when mac80211 requests
protection for the frame.

To achieve the last item, set the rate-control
RTS-requested flag for all stations that we have
aggregation sessions with, and set the protection
required flag when sending aggregated frames (on
those devices where this is required).

Since otherwise bugs can occur, do not allow the
user to override the RTS-for-aggregation setting
from sysfs any more.

Finally, also clean up the way all these flags get
set in the driver and move everything into the
device-specific functions.

Cc: stable@kernel.org [2.6.35]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/libertas/cfg.o
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’

Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 5f7aebd8.

Apparently, that PCI ID data was incorrectly taken from the subsystem
information.  The actual ID matches another already known ID.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on patches from Sonny Rao and Milton Miller...

Combined the patches to fix up clean_tx_irq and clean_rx_irq.

The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.

This bug was found during stress testing and adding this barrier has
been shown to fix it.  The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().

This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.

Previously Submitted to e1000-devel only for ixgbe

http://marc.info/?l=e1000-devel&m=126593062701537&w=3



We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.

CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error.  This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.

Also frames were being priority VLAN tagged even without DCB
enabled.  This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.

Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>