This fixes a bug introduced in commit
de847272
"3c59x: Use fine-grained locks for MII and windowed register access".

vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead.  However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.

Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock.  Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt().  This also removes the
potential for calling vortex_rx() on a later-generation NIC.

Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC5722 prohibits reassembling IPv6 fragments when some data overlaps.

Bug spotted by Zhang Zuotao <zuotao.zhang@6wind.com>.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC5722 prohibits reassembling fragments when some data overlaps.

Bug spotted by Zhang Zuotao <zuotao.zhang@6wind.com>.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a net device is implementing the select_queue callback and is part of
a bridge, frames coming from the bridge already have a tx queue associated
to the socket (introduced in commit a4ee3ce3,
"net: Use sk_tx_queue_mapping for connected sockets"). The call to
sk_tx_queue_get will then return the tx queue used by the bridge instead
of calling the select_queue callback.

In case of mac80211 this broke QoS which is implemented by using the
select_queue callback. Furthermore it introduced problems with rt2x00
because frames with the same TID and RA sometimes appeared on different
tx queues which the hw cannot handle correctly.

Fix this by always calling select_queue first if it is available and only
afterwards use the socket tx queue mapping.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).

Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.

jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave reported an rcu lockdep warning on 2.6.35.4 kernel

task->cgroups and task->cgroups->subsys[i] are protected by RCU.
So we avoid accessing invalid pointers here. This might happen,
for example, when you are deref-ing those pointers while someone
move @task from one cgroup to another.

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.

So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrong packet statistics for multicast Rx was causing net-snmp error messages
every 15 seconds. Instead of picking the multicast stats from hardware,
now maintain it in the driver itself.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a lockdep warning:

[  516.287584] =========================================================
[  516.288386] [ INFO: possible irq lock inversion dependency detected ]
[  516.288386] 2.6.35b #7
[  516.288386] ---------------------------------------------------------
[  516.288386] swapper/0 just changed the state of lock:
[  516.288386]  (&qdisc_tx_lock){+.-...}, at: [<c12eacda>] est_timer+0x62/0x1b4
[  516.288386] but this lock took another, SOFTIRQ-unsafe lock in the past:
[  516.288386]  (est_tree_lock){+.+...}
[  516.288386] 
[  516.288386] and interrupts could create inverse lock ordering between them.
...

So, est_tree_lock needs BH protection because it's taken by
qdisc_tx_lock, which is used both in BH and process contexts.
(Full warning with this patch at netdev, 02 Sep 2010.)

Fixes commit: ae638c47
("pkt_sched: gen_estimator: add a new lock")

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix Passive FTP problem in ip_vs_ftp:

- Do not oops in nf_nat_set_seq_adjust (adjust_tcp_sequence) when
  iptable_nat module is not loaded

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit de6be6c1.

After some discussion with Jarek Poplawski and Eric Dumazet, we've
decided that this change is incorrect.

Signed-off-by: David S. Miller <davem@davemloft.net>

Packets entering GRO might have different headrooms, even for a given
flow (because of implementation details in drivers, like copybreak).
We cant force drivers to deliver packets with a fixed headroom.

1) fix skb_segment()

skb_segment() makes the false assumption headrooms of fragments are same
than the head. When CHECKSUM_PARTIAL is used, this can give csum_start
errors, and crash later in skb_copy_and_csum_dev()

2) allocate a minimal skb for head of frag_list

skb_gro_receive() uses netdev_alloc_skb(headroom + skb_gro_offset(p)) to
allocate a fresh skb. This adds NET_SKB_PAD to a padding already
provided by netdevice, depending on various things, like copybreak.

Use alloc_skb() to allocate an exact padding, to reduce cache line
needs:
NET_SKB_PAD + NET_IP_ALIGN

bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=16626



Many thanks to Plamen Petrov, testing many debugging patches !
With help of Jarek Poplawski.

Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a similar vain to commit 17762060
("bridge: Clear IPCB before possible entry into IP stack")

Any time we call into the IP stack we have to make sure the state
there is as expected by the ipv4 code.

With help from Eric Dumazet and Herbert Xu.

Reported-by: Bandan Das <bandan.das@stratus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vortex_ioctl() was grabbing vortex_private::lock around its call to
generic_mii_ioctl().  This is no longer necessary since there are more
specific locks which the mdio_{read,write}() functions will obtain.
Worse, those functions do not save and restore IRQ flags when locking
the MII state, so interrupts will be enabled when generic_mii_ioctl()
returns.

Since there is currently no need for any function to call
mdio_{read,write}() while holding another spinlock, do not change them
to save and restore IRQ flags but remove the specification of ordering
between vortex_private::lock and vortex_private::mii_lock.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's something very important I forgot to tell you.
 What?

 Don't cross the GRO streams.
 Why?

 It would be bad.
 I'm fuzzy on the whole good/bad thing. What do you mean, "bad"?

 Try to imagine all the Internet as you know it stopping instantaneously
  and every bit in every packet swapping at the speed of light.
 Total packet reordering.
 Right. That's bad. Okay. All right. Important safety tip. Thanks, Hubert

The simplest way to stop this is just avoid doing GRO on the second port.
Very few Marvell boards support two ports per ring, and GRO is just
an optimization.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Attached is a small patch to remove a warning ("warning: ISO C90 forbids
mixed declarations and code" with gcc 4.3.2).

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes init_vf() function, so on each new backlog period parent's
cl_cfmin is properly updated (including further propgation towards the root),
even if the activated leaf has no upperlimit curve defined.

Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdiobus resources must be released on exit

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While reviewing commit 1c40be12, I
 audited other users of tc_action_ops->dump for information leaks.

 That commit covered almost all of them but act_police still had a leak.

 opt.limit and opt.capab aren't zeroed out before the structure is
 passed out.

 This patch uses the C99 initializers to zero everything unused out.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Its currently illegal to call kthread_stop(NULL)

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change just add the IBM eHEA 10Gb network drivers as supported.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.

Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.

Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Otherwise lockdep complains...

https://bugzilla.kernel.org/show_bug.cgi?id=17311



[ INFO: possible circular locking dependency detected ]
2.6.36-rc2-git4 #12
-------------------------------------------------------
kworker/0:3/3630 is trying to acquire lock:
 (rtnl_mutex){+.+.+.}, at: [<ffffffff813396c7>] rtnl_lock+0x12/0x14

but task is already holding lock:
 (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa014b129>]
rfkill_switch_all+0x24/0x49 [rfkill]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (rfkill_global_mutex){+.+.+.}:
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffffa014b4ab>] rfkill_register+0x2b/0x29c [rfkill]
       [<ffffffffa0185ba0>] wiphy_register+0x1ae/0x270 [cfg80211]
       [<ffffffffa0206f01>] ieee80211_register_hw+0x1b4/0x3cf [mac80211]
       [<ffffffffa0292e98>] iwl_ucode_callback+0x9e9/0xae3 [iwlagn]
       [<ffffffff812d3e9d>] request_firmware_work_func+0x54/0x6f
       [<ffffffff81065d15>] kthread+0x8c/0x94
       [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10

-> #1 (cfg80211_mutex){+.+.+.}:
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffffa018605e>] cfg80211_get_dev_from_ifindex+0x1b/0x7c [cfg80211]
       [<ffffffffa0189f36>] cfg80211_wext_giwscan+0x58/0x990 [cfg80211]
       [<ffffffff8139a3ce>] ioctl_standard_iw_point+0x1a8/0x272
       [<ffffffff8139a529>] ioctl_standard_call+0x91/0xa7
       [<ffffffff8139a687>] T.723+0xbd/0x12c
       [<ffffffff8139a727>] wext_handle_ioctl+0x31/0x6d
       [<ffffffff8133014e>] dev_ioctl+0x63d/0x67a
       [<ffffffff8131afd9>] sock_ioctl+0x48/0x21d
       [<ffffffff81102abd>] do_vfs_ioctl+0x4ba/0x509
       [<ffffffff81102b5d>] sys_ioctl+0x51/0x74
       [<ffffffff81009e02>] system_call_fastpath+0x16/0x1b

-> #0 (rtnl_mutex){+.+.+.}:
       [<ffffffff810796b0>] __lock_acquire+0xa93/0xd9a
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffff813396c7>] rtnl_lock+0x12/0x14
       [<ffffffffa0185cb5>] cfg80211_rfkill_set_block+0x1a/0x7b [cfg80211]
       [<ffffffffa014aed0>] rfkill_set_block+0x80/0xd5 [rfkill]
       [<ffffffffa014b07e>] __rfkill_switch_all+0x3f/0x6f [rfkill]
       [<ffffffffa014b13d>] rfkill_switch_all+0x38/0x49 [rfkill]
       [<ffffffffa014b821>] rfkill_op_handler+0x105/0x136 [rfkill]
       [<ffffffff81060708>] process_one_work+0x248/0x403
       [<ffffffff81062620>] worker_thread+0x139/0x214
       [<ffffffff81065d15>] kthread+0x8c/0x94
       [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>

Once we started enforcing the a nl_table[] entry exist for
a protocol, NETLINK_USERSOCK stopped working.  Add a dummy
table entry so that it works again.

Reported-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If irda_open_tsap() fails, the irda_bind() code tries to destroy
the ->ias_obj object by hand, but does so wrongly.

In particular, it fails to a) release the hashbin attached to the
object and b) reset the self->ias_obj pointer to NULL.

Fix both problems by using irias_delete_object() and explicitly
setting self->ias_obj to NULL, just as irda_release() does.

Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wireless extensions have an unfortunate, undocumented
requirement which requires drivers to always fill
iwp->length when returning a successful status. When
a driver doesn't do this, it leads to a kernel heap
content leak when userspace offers a larger buffer
than would have been necessary.

Arguably, this is a driver bug, as it should, if it
returns 0, fill iwp->length, even if it separately
indicated that the buffer contents was not valid.

However, we can also at least avoid the memory content
leak if the driver doesn't do this by setting the iwp
length to max_tokens, which then reflects how big the
buffer is that the driver may fill, regardless of how
big the userspace buffer is.

To illustrate the point, this patch also fixes a
corresponding cfg80211 bug (since this requirement
isn't documented nor was ever pointed out by anyone
during code review, I don't trust all drivers nor
all cfg80211 handlers to implement it correctly).

Cc: stable@kernel.org [all the way back]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new workqueue changes helped me find this bug
that's been lingering since the changes to the work
processing in mac80211 -- the work timer is never
deleted properly. Do that to avoid having it fire
after all data structures have been freed. It can't
be re-armed because all it will do, if running, is
schedule the work, but that gets flushed later and
won't have anything to do since all work items are
gone by now (by way of interface removal).

Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Michael reported that p54* never really entered power
save mode, even tough it was enabled.

It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...

Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This avoids a NULL pointer dereference as reported here:

	https://bugzilla.redhat.com/show_bug.cgi?id=625889



When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL.  So, we need to check the return value and avoid dereferencing it
in that case.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>

pcnet_cs:
    add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

The string clone is only used as a temporary copy of the argument val
within the while loop, and so it should be freed before leaving the
function.  The call to strsep, however, modifies clone, so a pointer to the
front of the string is kept in saved_clone, to make it possible to free it.

The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/

)

// <smpl>
@r exists@
local idexpression x;
expression E;
identifier l;
statement S;
@@

*x= \(kasprintf\|kstrdup\)(...);
...
if (x == NULL) S
... when != kfree(x)
    when != E = x
if (...) {
  <... when != kfree(x)
* goto l;
  ...>
* return ...;
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 886275ce (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:

  ~# modprobe libertas_sdio
  [   62.315124] libertas_sdio: Libertas SDIO driver
  [   62.319976] libertas_sdio: Copyright Pierre Ossman
  [   63.020629] DMA misaligned error with device 48
  [   63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
  [   66.005035] libertas: command 0x0003 timed out
  [   66.009826] libertas: Timeout submitting command 0x0003
  [   66.016296] libertas: PREP_CMD: command 0x0003 failed: -110

Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

caif does not build on ia64 starting with 2.6.32-rc1.  Using
asm/unaligned.h instead of linux/unaligned/le_byteshift.h fixes the issue.

include/linux/unaligned/le_byteshift.h:40:50: error: redefinition of 'get_unaligned_le16'
include/linux/unaligned/le_byteshift.h:45:50: error: redefinition of 'get_unaligned_le32'
include/linux/unaligned/le_byteshift.h:50:50: error: redefinition of 'get_unaligned_le64'
include/linux/unaligned/le_byteshift.h:55:51: error: redefinition of 'put_unaligned_le16'
include/linux/unaligned/le_byteshift.h:60:51: error: redefinition of 'put_unaligned_le32'
include/linux/unaligned/le_byteshift.h:65:51: error: redefinition of 'put_unaligned_le64'
include/linux/unaligned/le_struct.h:31:51: note: previous definition of 'put_unaligned_le64' was here

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves a missplaced sock_put(sk) after
bh_unlock_sock(sk)
like in other parts of AX25 driver.

Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>