This patch removes code that has been rendered useless by the previous patches
in this series.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch switches the emac implementation over to the newly separated
MDIO driver.

With this, the mdio bus frequency defaults to a safe 2.2MHz.  Boards may
optionally specify a bus frequency via platform data.

The phy identification scheme has been modified to use a phy bus id instead
of a mask.  This largely serves to eliminate the "phy search" code in emac
init.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Davinci's MDIO controller is present on other TI devices, without an
accompanying EMAC.  For example, on tnetv107x, the same MDIO module is used in
conjunction with a 3-port switch hardware.

By separating the MDIO controller code into its own platform driver, this
patch allows common logic to be reused on such platforms.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Fixed formatting (tabs and line breaks).

The CHELSIO_GET_QSET_NUM device ioctl allows unprivileged users to read
4 bytes of uninitialized stack memory, because the "addr" member of the
ch_reg struct declared on the stack in cxgb_extension_ioctl() is not
altered or zeroed before being copied back to the user.  This patch
takes care of it.

Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed formatting (tabs and line breaks).

The EQL_GETMASTRCFG device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "master_name" member of
the master_config_t struct declared on the stack in eql_g_master_cfg()
is not altered or zeroed before being copied back to the user.  This
patch takes care of it.

Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed formatting (tabs and line breaks).

The TIOCGICOUNT device ioctl allows unprivileged users to read
uninitialized stack memory, because the "reserved" member of the
serial_icounter_struct struct declared on the stack in hso_get_count()
is not altered or zeroed before being copied back to the user.  This
patch takes care of it.

Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to use spinlocks in vortex_{set|get}_wol.
This also fixes a bug:
[  254.214993] 3c59x 0000:00:0d.0: PME# enabled
[  254.215021] BUG: sleeping function called from invalid context at kernel/mutex.c:94
[  254.215030] in_atomic(): 0, irqs_disabled(): 1, pid: 4875, name: ethtool
[  254.215042] Pid: 4875, comm: ethtool Tainted: G        W   2.6.36-rc3+ #7
[  254.215049] Call Trace:
[  254.215050]  [] __might_sleep+0xb1/0xb6
[  254.215050]  [] mutex_lock+0x17/0x30
[  254.215050]  [] acpi_enable_wakeup_device_power+0x2b/0xb1
[  254.215050]  [] acpi_pm_device_sleep_wake+0x42/0x7f
[  254.215050]  [] acpi_pci_sleep_wake+0x5d/0x63
[  254.215050]  [] platform_pci_sleep_wake+0x1d/0x20
[  254.215050]  [] __pci_enable_wake+0x90/0xd0
[  254.215050]  [] acpi_set_WOL+0x8e/0xf5 [3c59x]
[  254.215050]  [] vortex_set_wol+0x4e/0x5e [3c59x]
[  254.215050]  [] dev_ethtool+0x1cf/0xb61
[  254.215050]  [] ? debug_mutex_free_waiter+0x45/0x4a
[  254.215050]  [] ? __mutex_lock_common+0x204/0x20e
[  254.215050]  [] ? __mutex_lock_slowpath+0x12/0x15
[  254.215050]  [] ? mutex_lock+0x23/0x30
[  254.215050]  [] dev_ioctl+0x42c/0x533
[  254.215050]  [] ? _cond_resched+0x8/0x1c
[  254.215050]  [] ? lock_page+0x1c/0x30
[  254.215050]  [] ? page_address+0x15/0x7c
[  254.215050]  [] ? filemap_fault+0x187/0x2c4
[  254.215050]  [] sock_ioctl+0x1d4/0x1e0
[  254.215050]  [] ? sock_ioctl+0x0/0x1e0
[  254.215050]  [] vfs_ioctl+0x19/0x33
[  254.215050]  [] do_vfs_ioctl+0x424/0x46f
[  254.215050]  [] ? selinux_file_ioctl+0x3c/0x40
[  254.215050]  [] sys_ioctl+0x40/0x5a
[  254.215050]  [] sysenter_do_call+0x12/0x22

vortex_set_wol protected with a spinlock, but nested  acpi_set_WOL acquires a mutex inside atomic context.
Ethtool operations are already serialized by RTNL mutex, so it is safe to drop the locks.

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some pcnet_cs compatible cards require an exact 16-lines match
of the ioport areas specified in CIS, but set the "iolines"
value in the CIS incorrectly. We can easily work around this
issue -- same as we do in serial_cs -- by first trying setting
iolines to the CIS-specified value, and then trying a 16-line
match.

Reported-and-tested-by: Wolfram Sang <w.sang@pengutronix.de>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.

This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.

Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there.  That explained the inability to form an
802.3ad-based bond.  For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.

This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.

Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line.  Partly the reason this
bug was introduced is because code was too complicated.  I've simplified
it a little.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.

As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_alloc_skb_ip_align() helper and do correct allocation

Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not.  However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command.  Therefore this is at least a local
denial-of-service vulnerability.

Change it to check before writing each entry and to return an error if
the buffer is already full.

Compile-tested only.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.

So turn off SG, and we'll tackle making this work
properly in net-next-2.6

Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a simplified version of the original patch from James Courtier-Dutton.

>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a bug introduced in commit
de847272
"3c59x: Use fine-grained locks for MII and windowed register access".

vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead.  However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.

Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock.  Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt().  This also removes the
potential for calling vortex_rx() on a later-generation NIC.

Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).

Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.

jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.

So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrong packet statistics for multicast Rx was causing net-snmp error messages
every 15 seconds. Instead of picking the multicast stats from hardware,
now maintain it in the driver itself.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit de6be6c1.

After some discussion with Jarek Poplawski and Eric Dumazet, we've
decided that this change is incorrect.

Signed-off-by: David S. Miller <davem@davemloft.net>

vortex_ioctl() was grabbing vortex_private::lock around its call to
generic_mii_ioctl().  This is no longer necessary since there are more
specific locks which the mdio_{read,write}() functions will obtain.
Worse, those functions do not save and restore IRQ flags when locking
the MII state, so interrupts will be enabled when generic_mii_ioctl()
returns.

Since there is currently no need for any function to call
mdio_{read,write}() while holding another spinlock, do not change them
to save and restore IRQ flags but remove the specification of ordering
between vortex_private::lock and vortex_private::mii_lock.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's something very important I forgot to tell you.
 What?

 Don't cross the GRO streams.
 Why?

 It would be bad.
 I'm fuzzy on the whole good/bad thing. What do you mean, "bad"?

 Try to imagine all the Internet as you know it stopping instantaneously
  and every bit in every packet swapping at the speed of light.
 Total packet reordering.
 Right. That's bad. Okay. All right. Important safety tip. Thanks, Hubert

The simplest way to stop this is just avoid doing GRO on the second port.
Very few Marvell boards support two ports per ring, and GRO is just
an optimization.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdiobus resources must be released on exit

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is the next patch which is fixing missing header
which were removed from prom.h.

Related patches:
"of/address: Clean up function declarations" (sha1 id 22ae782f)
"of: Fix missing includes" (sha1 id f1ca09b2)

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.

Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.

Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Michael reported that p54* never really entered power
save mode, even tough it was enabled.

It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...

Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This avoids a NULL pointer dereference as reported here:

	https://bugzilla.redhat.com/show_bug.cgi?id=625889



When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL.  So, we need to check the return value and avoid dereferencing it
in that case.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>

pcnet_cs:
    add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 886275ce (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:

  ~# modprobe libertas_sdio
  [   62.315124] libertas_sdio: Libertas SDIO driver
  [   62.319976] libertas_sdio: Copyright Pierre Ossman
  [   63.020629] DMA misaligned error with device 48
  [   63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
  [   66.005035] libertas: command 0x0003 timed out
  [   66.009826] libertas: Timeout submitting command 0x0003
  [   66.016296] libertas: PREP_CMD: command 0x0003 failed: -110

Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Qlge is freeing the buffers before stopping the card DMA, and
this can cause some severe error, as a EEH event on PPC.

This patch just stop the card and then free the resources.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc
complain:

drivers/net/pxa168_eth.c:657: warning:
	cast to pointer from integer of different size

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function changed recently.  It now takes a struct
ifreq pointer directly.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A couple issues here:
* Some resources weren't released.
* If alloc_etherdev() failed it would have caused a NULL dereference
  because "pep" would be null when we checked "if (pep->clk)".
* Also it's better to propagate the error codes from mdiobus_register()
  instead of just returning -ENOMEM.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"pep->pd" isn't checked consistently in this function.  For example it's
dereferenced unconditionally on the next line after the end of the if
condition.  This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:

  Unable to handle kernel paging request for data at address 0x0000024c
  Oops: Kernel access of bad area, sig: 11 [#1]
  PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
  P1021 RDB
  Modules linked in:
  NIP: c0345dac LR: c0345dac CTR: c0345d84
  TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
  [...]
  NIP [c0345dac] adjust_link+0x28/0x19c
  LR [c0345dac] adjust_link+0x28/0x19c
  Call Trace:
  [c0d25f00] [000045e1] 0x45e1 (unreliable)
  [c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
  [...]

Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:

static int init_phy(struct net_device *dev)
{
	...
	priv->phydev = of_phy_connect(...);
	...
}

So that adjust_link could retrieve it back:

static void adjust_link(struct net_device *dev)
{
	...
	struct phy_device *phydev = priv->phydev;
	...
}

If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).

Now, phy_connect starts the PHY state machine before returning phydev to
the driver:

	phy_start_machine(phydev, NULL);

	if (phydev->irq > 0)
		phy_start_interrupts(phydev);

	return phydev;

The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.

To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>