The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.

This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a bug in my commit c978e7bb
("hisax: Fix unchecked alloc_skb() return.")

One of the l2->flag checks is wrong.

Even worse it turns out I'm duplicating an existing function,
so use that instead.

Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETDEV_NOTIFY_PEER is an explicit request by the driver to send a link
notification while NETDEV_UP/NETDEV_CHANGEADDR generate link
notifications as a sort of side effect.

In the later cases the sysctl option is present because link
notification events can have undesired effects e.g. if the link is
flapping. I don't think this applies in the case of an explicit
request from a driver.

This patch makes NETDEV_NOTIFY_PEER unconditional, if preferred we
could add a new sysctl for this case which defaults to on.

This change causes Xen post-migration ARP notifications (which cause
switches to relearn their MAC tables etc) to be sent by default.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF Driver should use mailbox command timeout specified in t4fw_interface.h
rather than hard-coded value of 500ms.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a Virtual Machine is rebooted, KVM currently fails to issue a Function
Level Reset against any "Attached PCI Devices" (AKA "PCI Passthrough").  In
addition to leaving the attached device in a random state in the next booted
kernel (which sort of violates the entire idea of a reboot reseting hardware
state), this leaves our peer thinking that the link is still up.  (Note that
a bug has been filed with the KVM folks, #25332, but there's been no
response on that as of yet.)  So, we add a "->shutdown()" method for the
Virtual Function PCI Device to handle administrative shutdowns like a
reboot.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_DEBUG_FS we get "ERR_PTR()"s back from the debugfs routines
instead of NULL.  Use the right predicates to check for this.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check module parameter validity in the module initialization routine instead
of the PCI Device Probe routine.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the specification of hardware,
the processing at the time of driver starting was modified.

This device write automatically the MAC address read from serial ROM
into a MAC Adress1A/1B register at the time of power on reset.
However, when stable clock is not supplied,
the writing of MAC Adress1A/1B register may not be completed.
In this case, it is necessary to load MAC address to MAC Address1A/1B register
by the MAC Address1 load register.

This patch always does the above processing,
in order not to be dependent on system environment.

Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes this build warning:

drivers/net/wireless/iwlwifi/iwl-3945.c:411:13: warning: 'iwl3945_good_plcp_health' defined but not used

As per Johannes Berg.

Signed-off-by: David S. Miller <davem@davemloft.net>

The statement 'select CAN_SOFTING' may ignore the dependancies
for CAN_SOFTING while selecting CAN_SOFTING_CS, as is therefore a bad choice.

Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As noticed by Eric, nf_iterate doesn't use RCU correctly by
accessing the prev pointer of a RCU protected list element when
a verdict of NF_REPEAT is issued.

Fix by jumping backwards to the hook invocation directly instead
of loading the previous list element before continuing the list
iteration.

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

This PCH_GBE driver had an issue that the receiving data is not normal.
This driver had not removed correctly the padding data
which the DMA include in receiving data.

This patch fixed this issue.

Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables it by default when the driver starts.
This has been required by many people and seems to actually be
useful on STB.
At any rate, the WoL modes can be selected and turned-on/off
by using the ethtool at run-time by users.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If alloc_skb() fails to allocate memory and returns NULL then we want to
return -ENOMEM from drivers/atm/solos-pci.c::popen() regardless of the
value of net_ratelimit(). The way the code is today, we may not return if
net_ratelimit() returns 0, then we'll proceed to pass a NULL pointer to
skb_put() which will blow up in our face.
This patch ensures that we always return -ENOMEM on alloc_skb() failure
and only let the dev_warn() be controlled by the value of net_ratelimit().

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In drivers/net/usb/hso.c::hso_create_bulk_serial_device() we have this
code:
...
	serial = kzalloc(sizeof(*serial), GFP_KERNEL);
	if (!serial)
		goto exit;
...
exit:
	hso_free_tiomget(serial);
...
hso_free_tiomget() directly dereferences its argument, which in the
example above is a NULL pointer, ouch.
I could just add a 'if (serial)' test at the 'exit' label, but since most
freeing functions in the kernel accept NULL pointers (and it seems like
this was also assumed here) I opted to instead change 'hso_free_tiomget()'
so that it is safe to call it with a NULL argument. I also modified the
function to get rid of a pointles conditional before the call to
'usb_free_urb()' since that function already tests for NULL itself -
besides fixing the NULL deref this change also buys us a few bytes in
size.
Before:
$ size drivers/net/usb/hso.o
   text    data     bss     dec     hex filename
  32200     592    9960   42752    a700 drivers/net/usb/hso.o
After:
$ size drivers/net/usb/hso.o
   text    data     bss     dec     hex filename
  32196     592    9960   42748    a6fc drivers/net/usb/hso.o

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesper Juhl noticed that l2_pull_iqueue() does not
check to see if alloc_skb() fails.

Fix this by first trying to reallocate the headroom
if necessary, rather than later after we've made hard
to undo state changes.

Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

USB Network driver infrastructure: Fix leak when usb_autopm_get_interface() returns less than zero in kevent().

We'll leak the memory allocated to 'urb' in
drivers/net/usb/usbnet.c:kevent() when we 'goto fail_lowmem' and the 'urb'
variable goes out of scope while still completely unused.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

nla_nest_start() may return NULL. If it does then we'll blow up in
nla_nest_end() when we dereference the pointer.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The app_data priority may not be the same for all net devices.
In order for stacks with application notifiers to identify the
specific net device dcb_app_type should be passed in the ptr.

This allows handlers to use dev_get_by_name() to pin priority
to net devices.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it turns out we never need to walk through the list of multicast
groups subscribed by the bridge interface itself (the only time we'd
want to do that is when we shut down the bridge, in which case we
simply walk through all multicast groups), we don't really need to
keep an hlist for mp->mglist.

This means that we can replace it with just a single bit to indicate
whether the bridge interface is subscribed to a group.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a couple of spots where we are supposed to modify the port
group timer (p->timer) we instead modify the bridge interface
group timer (mp->timer).

The effect of this is mostly harmless.  However, it can cause
port subscriptions to be longer than they should be, thus making
snooping less effective.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The list mp->mglist is used to indicate whether a multicast group
is active on the bridge interface itself as opposed to one of the
constituent interfaces in the bridge.

Unfortunately the operation that adds the mp->mglist node to the
list neglected to check whether it has already been added.  This
leads to list corruption in the form of nodes pointing to itself.

Normally this would be quite obvious as it would cause an infinite
loop when walking the list.  However, as this list is never actually
walked (which means that we don't really need it, I'll get rid of
it in a subsequent patch), this instead is hidden until we perform
a delete operation on the affected nodes.

As the same node may now be pointed to by more than one node, the
delete operations can then cause modification of freed memory.

This was observed in practice to cause corruption in 512-byte slabs,
most commonly leading to crashes in jbd2.

Thanks to Josef Bacik for pointing me in the right direction.

Reported-by: Ian Page Hands <ihands@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5811662b ("net: use the macros
defined for the members of flowi") accidentally removed the setting of
IPPROTO_GRE from the struct flowi in ipgre_tunnel_xmit. This patch
restores it.

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 80c802f3 (xfrm: cache bundles instead of policies for
outgoing flows) introduced possible oopse when dst_alloc returns NULL.

Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-I (include path) should be specified for host builds.
This one was overlooked somehow.  Fixes
https://bugzilla.kernel.org/show_bug.cgi?id=25902



Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Alexey Salmin <alexey.salmin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.

Make sure napi is scheduled subsequent to each napi_enable.

Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Olaf Kirch <okir@suse.de>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

In x25_link_free(), we destroy 'nb' before dereferencing
'nb->dev'.  Don't do this, because 'nb' might be freed
by then.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch "[PATCH 1/3] pch_can: fix 800k comms issue" is wrong.
I should have modified tseg1_min not tseg2_min.
This patch reverts tseg2_min to 1 and set tseg1_min to 2.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some cases try to modify const strings, and in any event the
CVS revision strings have not changed in over ten years making
these printouts completely worthless.

Just kill all of this stuff off.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Randy Dunlap <randy.dunlap@oracle.com>

softing_cs.c uses kzalloc & kfree, so it needs to include linux/slab.h.

drivers/net/can/softing/softing_cs.c:234: error: implicit declaration of function 'kfree'
drivers/net/can/softing/softing_cs.c:271: error: implicit declaration of function 'kzalloc'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When suspending an associated system, and then resuming,
the station vif is being reconfigured without taking the
sdata->u.mgd.mtx lock, which results in the following warning:

WARNING: at net/mac80211/mlme.c:101 ieee80211_ap_probereq_get+0x58/0xb8 [mac80211]()
Modules linked in: wl12xx_sdio wl12xx firmware_class crc7 mac80211 cfg80211 [last unloaded: crc7]
Backtrace:
[<c005432c>] (dump_backtrace+0x0/0x118) from [<c0376e28>] (dump_stack+0x20/0x24)
 r7:00000000 r6:bf12d6ec r5:bf154aac r4:00000065
[<c0376e08>] (dump_stack+0x0/0x24) from [<c0079104>] (warn_slowpath_common+0x5c/0x74)
[<c00790a8>] (warn_slowpath_common+0x0/0x74) from [<c0079148>] (warn_slowpath_null+0x2c/0x34)
 r9:000024ff r8:cd006460 r7:00000001 r6:00000000 r5:00000000
r4:cf1394a0
[<c007911c>] (warn_slowpath_null+0x0/0x34) from [<bf12d6ec>] (ieee80211_ap_probereq_get+0x58/0xb8 [mac80211])
[<bf12d694>] (ieee80211_ap_probereq_get+0x0/0xb8 [mac80211]) from [<bf19cd04>] (wl1271_cmd_build_ap_probe_req+0x30/0xf8 [wl12xx])
 r4:cd007440
[<bf19ccd4>] (wl1271_cmd_build_ap_probe_req+0x0/0xf8 [wl12xx]) from [<bf1995f4>] (wl1271_op_bss_info_changed+0x4c4/0x808 [wl12xx])
 r5:cd007440 r4:000003b4
[<bf199130>] (wl1271_op_bss_info_changed+0x0/0x808 [wl12xx]) from [<bf122168>] (ieee80211_bss_info_change_notify+0x1a4/0x1f8 [mac80211])
[<bf121fc4>] (ieee80211_bss_info_change_notify+0x0/0x1f8 [mac80211]) from [<bf141e80>] (ieee80211_reconfig+0x4d0/0x668 [mac80211])
 r8:cf0eeea4 r7:cd00671c r6:00000000 r5:cd006460 r4:cf1394a0
[<bf1419b0>] (ieee80211_reconfig+0x0/0x668 [mac80211]) from [<bf137dd4>] (ieee80211_resume+0x60/0x70 [mac80211])
[<bf137d74>] (ieee80211_resume+0x0/0x70 [mac80211]) from [<bf0eb930>] (wiphy_resume+0x6c/0x7c [cfg80211])
 r5:cd006248 r4:cd006110
[<bf0eb8c4>] (wiphy_resume+0x0/0x7c [cfg80211]) from [<c0241024>] (legacy_resume+0x38/0x70)
 r7:00000000 r6:00000000 r5:cd006248 r4:cd0062fc
[<c0240fec>] (legacy_resume+0x0/0x70) from [<c0241478>] (device_resume+0x168/0x1a0)
 r8:c04ca8d8 r7:cd00627c r6:00000010 r5:cd006248 r4:cd0062fc
[<c0241310>] (device_resume+0x0/0x1a0) from [<c0241600>] (dpm_resume_end+0xf8/0x3bc)
 r7:00000000 r6:00000005 r5:cd006248 r4:cd0062fc
[<c0241508>] (dpm_resume_end+0x0/0x3bc) from [<c00b2a24>] (suspend_devices_and_enter+0x1b0/0x204)
[<c00b2874>] (suspend_devices_and_enter+0x0/0x204) from [<c00b2b68>] (enter_state+0xf0/0x148)
 r7:c037e978 r6:00000003 r5:c043d807 r4:00000000
[<c00b2a78>] (enter_state+0x0/0x148) from [<c00b20a4>] (state_store+0xa4/0xcc)
 r7:c037e978 r6:00000003 r5:00000003 r4:c043d807
[<c00b2000>] (state_store+0x0/0xcc) from [<c01fc90c>] (kobj_attr_store+0x20/0x24)
[<c01fc8ec>] (kobj_attr_store+0x0/0x24) from [<c0157120>] (sysfs_write_file+0x11c/0x150)
[<c0157004>] (sysfs_write_file+0x0/0x150) from [<c0100f84>] (vfs_write+0xc0/0x14c)
[<c0100ec4>] (vfs_write+0x0/0x14c) from [<c01010e4>] (sys_write+0x4c/0x78)
 r8:40126000 r7:00000004 r6:cf1a7c80 r5:00000000 r4:00000000
[<c0101098>] (sys_write+0x0/0x78) from [<c00500c0>] (ret_fast_syscall+0x0/0x30)
 r8:c00502c8 r7:00000004 r6:403525e8 r5:40126000 r4:00000004

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599



Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.

For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.

Bug reporter confirmed that removing plcp check fixed problem for him.

Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org  # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver will be in a deadlock, When the rx offload is set by ethtool.
The pch_gbe_reinit_locked function was modified.

Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TCP tracking code has a special case that allows to return
NF_REPEAT if we receive a new SYN packet while in TIME_WAIT state.

In this situation, the TCP tracking code destroys the existing
conntrack to start a new clean session.

[DESTROY] tcp      6 src=192.168.0.2 dst=192.168.1.2 sport=38925 dport=8000 src=192.168.1.2 dst=192.168.1.100 sport=8000 dport=38925 [ASSURED]
    [NEW] tcp      6 120 SYN_SENT src=192.168.0.2 dst=192.168.1.2 sport=38925 dport=8000 [UNREPLIED] src=192.168.1.2 dst=192.168.1.100 sport=8000 dport=38925

However, this is a problem for the iptables' CT target event filtering
which will not work in this case since the conntrack template will not
be there for the new session. To fix this, we reassign the conntrack
template to the packet if we return NF_REPEAT.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.

The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>