This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver increments the tx_timeout counter (an error counter)
when simply resetting the part with outstanding transmit work pending.
This is an unnecessary count of an error, when all we should be doing is
just resetting the part and discarding the transmits.  With this change the
only increment of tx_timeout is when the stack calls the watchdog reset
function due to a true Tx timeout.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.

The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.

Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed.  We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ERROR: that open brace { should be on the previous line

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ERROR: trailing statements should be on next line

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ERROR: Macros with complex values should be enclosed in parenthesis

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some drivers are using skb_transport_offset(skb) instead of skb->csum_start
for NETIF_F_HW_CSUM offload.  This does not matter now, but if someone
implements checksumming of encapsulated packets then this will break silently.

TSO output paths are left as they are, since they are for IP+TCP only
(might be worth converting though).

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

flush_scheduled_work() is on its way out.  This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.

Directly cancel the used works on driver detach and flush them in
other cases.

The conversions are mostly straight forward and the only dangers are,

* Forgetting to cancel/flush one or more used works.

* Cancelling when a work should be flushed (ie. the work must be
  executed once scheduled whether the driver is detaching or not).

I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding this default case resolves the issue.

v2- Removed "break" in default case based on feedback

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct error messages when setting up Rx resources and when checking
module parameters.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

tx_desc can be dereferenced as a null pointer when count is passed in
as 0.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide support to e1000e for displaying the new format of the PBA found
in the EEPROM.  The unique PBA identifier is no longer restricted to
hexadecimal numbers and must now be read and displayed as a string.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read.  To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits)
were being configured incorrectly when device goes to D3 state.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When link partner is sending continuous Config symbols, the 82571 Serdes
FIFO can overflow resulting in Invalid bit getting set.  To resolve this,
if Sync and Config bits are both 1 ignore the Invalid bit and restart
auto-negotiation.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The workaround function e1000_configure_k1_pchlan() assumes the h/w
semaphore is already acquired.  This was originally missed when setting up
the part for the ethtool loopback test.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Increasing the transmit fifo by 4K (by decreasing the receive fifo size
specified in .pba by the same amount) increases Tx performance.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On certain 82571-based mezzanine NICs in some blade servers, the ethtool
link test can fail due to the serdes_has_link flag not set correctly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel goes BUG() at the time 'ethtool -p eth0 3' comes
back, which is due to adapter->led_blink_task initialized
several times.  At the time it is still running this results
in a corrupted task_list of the associated workqueue.

The fix is to move the workqueue initialization to the
probe function instead.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on work by Joe Perches <joe@perches.com>

Using static const to decrease data and overall object size.

CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>

Various drivers are using implementations of ethtool_ops::get_link
that are equivalent to the default ethtool_op_get_link().  Change
them to use that instead.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use vzalloc() and vzalloc_node() in net drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With enabling CONFIG_PCI_MSI, e1000e could work in MSI/MSI-X IRQ mode,
and netpoll controller didn't deal with those IRQ modes on e1000e.

This patch add the handling MSI/MSI-X IRQ modes to netpoll controller,
so that netconsole could work with those IRQ modes.

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver can fail initializing the hardware when manageability firmware
is performing concurrent MDIO operations because the hardware semaphore
scheme to prevent concurrent operations between software and firmware is
incorrect for 82574/82583.  Instead of using the SWSM register, the driver
should be using the EXTCNF_CTRL register.  A software mutex is also added
to prevent simultaneous software threads from performing similar concurrent
accesses.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

SerDes Link detection on certain 82571 mezzanine cards can fail when the
link is forced, the link partner does not recognize forced link and the
link partner sends null code words.  Detect the null code words and return
to auto-negotiation state which causes the link partner to begin responding
with valid code words.  Within a reasonable interval the link will finally
settle as forced by both partners.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Some parts need to execute resets during normal operation.  This flag
check ensures that those parts reset without needlessly alarming the
user.  Other unexpected resets by other parts will dump debug info
and message the reset action to the user, as originally intended.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some errors can be induced in the PHY via environmental testing
(specifically extreme temperature changes and electro static
discharge testing), and in the case of the PHY hanging due to
this input, this detects the problem and resets to continue.
This issue only applies to 82574 silicon.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb.  There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances.  However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>