Use netdev_err to standardise the error output.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_dbg to standardise the debug output.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions appear before their use, so we can remove the redundant
prototypes.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were using alloc_skb which doesn't create any headroom. Change it to
use netdev_alloc_skb to match most other drivers.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We export all the driver specific statistics via ethtool, so there is no need
to duplicate this in procfs.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables TCP checksum offload support for IPv6 on ibmveth.
This completely eliminates the generation and checking of the checksum
for IPv6 packets that are completely virtual and never touch a physical
network.  A basic TCPIPV6_STREAM netperf run showed a ~30% throughput
improvement when an MTU of 64000 was used.

This featured is enabled by default, as is the case for IPv4 checksum
offload.  When checksum offload is enabled the driver will negotiate
IPv4 and IPv6 offload with the firmware separately and enable what
is available.  As long as either IPv4 or IPv6 offload is supported
and enabled the device will report that checksum offload is enabled.
The device stats, available through ethtool, will display which
checksum offload features are supported/enabled by firmware.

Performance testing against a stock kernel shows no regression for IPv4
or IPv6 in terms of throughput or processor utilization with checksum
disabled or enabled.

Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove code in the device probe function where we set up the checksum
offload feature and replace it with a call to an existing function that
is doing the same.  This is done to clean up the driver in preparation
of adding IPv6 checksum offload support.

Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some machines we can improve the bandwidth by ensuring rx buffers are
not in the cache. Add a module option that is disabled by default that flushes
rx buffers on insertion.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmveth can scatter gather up to 6 segments. If we go over this then
we have no option but to call skb_linearize, like other drivers with
similar limitations do.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to order the read in ibmveth_rxq_pending_buffer and the read of
ibmveth_rxq_buffer_valid which are both cacheable memory. smp_rmb() is good
enough for this.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For small packets, create a new skb and copy the packet into it so we
avoid tearing down and creating a TCE entry.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the existing bounce buffer if we send a buffer under a certain size.
This saves the overhead of a TCE map/unmap.

I can't see any reason for the wmb() in the bounce buffer case, if we need
a barrier it will be before we call h_send_logical_lan but we have
nothing in the common case. Remove it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ibmveth adapter needs locking in the transmit routine to protect
the bounce_buffer but it sets LLTX and forgets to add any of its own
locking.

Just remove the deprecated LLTX option. Remove the stats lock in the process.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the moment we try and replenish the receive ring on every rx interrupt.
We even have a pool->threshold but aren't using it.

To limit the maximum latency incurred when refilling, change the threshold
from 1/2 to 7/8 and reduce the largest rx pool from 768 buffers to 512 which
should be more than enough.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace some modulus operators with an increment and compare to avoid
an integer divide.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cause TIPC to return EAGAIN if it is unable to enable a new Ethernet
bearer because one or more recently disabled Ethernet bearers are
temporarily consuming resources during shut down.  (The previous error
code, EDQUOT, is now returned only if all available Ethernet bearer
data structures are fully enabled at the time the request to enable an
additional bearer is received.)

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add code to expand the headroom of an outgoing TIPC message if the
sk_buff has insufficient room to hold the header for the associated
Ethernet device.  This change is necessary to ensure that messages
TIPC does not create itself (eg. incoming messages that are being
routed to another node) do not cause problems, since TIPC has no
control over the amount of headroom available in such messages.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Optimizes TIPC's name table translation code to avoid unnecessary
manipulation of the node address field of the resulting port id when
name translation fails.  This change is possible because a valid port
id cannot have a reference field of zero, so examining the reference
only is sufficient to determine if the translation was successful.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change several wan drivers to make strings and other initialize
only parameters const.

Compile tested only (with no new warnings)

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While porting GRO to r8169, I found this driver has a bug in its rx
path.

All skbs given to network stack had their ip_summed set to
CHECKSUM_NONE, while hardware said they had correct TCP/UDP checksums.

The reason is driver sets skb->ip_summed on the original skb before the
copy eventually done by copybreak. The fresh skb gets the ip_summed =
CHECKSUM_NONE value, forcing network stack to recompute checksum, and
preventing my GRO patch to work.

Fix is to make the ip_summed setting after skb copy.

Note : rx_copybreak current value is 16383, so all frames are copied...

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't call flush_workqueue() on the cxgb3 Work Queue in cxgb_down() when
we're being called from the fatal error task ... which is executing on the
cxgb3 Work Queue.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Platform code needs to deal with them now.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__alloc_skb() uses a memset() to clear all the beginning of skb,
including bitfields contained in 'flags1' & 'flags2'.

We dont need any more to use kmemcheck_annotate_bitfield() on these
fields. However, we still need it for the clone part, which is not
cleared.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct tulip_private is a bit large (order-1 allocation even on 32bit
arch), try to shrink it, remove its net_device_stats field.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation for recent changes to the tunables accept_ra and
forwarding.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to accepting router advertisement, the IPv6 stack does not send router
solicitations if forwarding is enabled.

This patch enables this behavior to be overruled by setting forwarding to the
special value 2.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current IPv6 behavior is to not accept router advertisements while
forwarding, i.e. configured as router.

This does make sense, a router is typically not supposed to be auto
configured. However there are exceptions and we should allow the
current behavior to be overwritten.

Therefore this patch enables the user to overrule the "if forwarding
enabled then don't listen to RAs" rule by setting accept_ra to the
special value of 2.

An alternative would be to ignore the forwarding switch alltogether
and solely accept RAs based on the value of accept_ra. However, I
found that if not intended, accepting RAs as a router can lead to
strange unwanted behavior therefore we it seems wise to only do so
if the user explicitely asks for this behavior.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

get_stats() method incorrectly clears a global array before folding
various stats. This can break SNMP applications.

Switch to 64 bit flavor to work on a user supplied buffer, and provide
64bit counters even on 32bit arches.

Fix a bug in bnad_netdev_hwstats_fill(), for rx_fifo_errors, missing a
folding (only the last counter was taken into account)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem

Clean the code up according to Documentation/CodingStyle.

Don't initialize the variable dont_send in arp_process().

Remove the temporary varialbe flags in arp_state_to_flags().

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a small helper ptype_head() to get the head to manipulate

dev_add_pack() & __dev_remove_pack() can use a spinlock without
blocking BH, since softirq use RCU, and these functions are run from
process context only.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct state range of PHY bus addresses (i.e. 0-31) in comment,
make spelling of PHY consistent in comments.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use correctly the in_pkts packet counter also for SCTP

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>