Commit 2e4840ed authored by Samu Onkalo's avatar Samu Onkalo Committed by Linus Torvalds
Browse files

drivers/leds/leds-lp5523.c: adjust delays and add comments to them



Delays were little bit too long.  Adjust delay times and add some comments
to them.
Signed-off-by: default avatarSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 09c76b0f
......@@ -205,11 +205,14 @@ static int lp5523_configure(struct i2c_client *client)
lp5523_write(client, LP5523_REG_RESET, 0xff);
usleep_range(10000, 100000);
usleep_range(10000, 20000); /*
* Exact value is not available. 10 - 20ms
* appears to be enough for reset.
*/
ret |= lp5523_write(client, LP5523_REG_ENABLE, LP5523_ENABLE);
/* Chip startup time after reset is 500 us */
usleep_range(1000, 10000);
/* Chip startup time is 500 us, 1 - 2 ms gives some margin */
usleep_range(1000, 2000);
ret |= lp5523_write(client, LP5523_REG_CONFIG,
LP5523_AUTO_INC | LP5523_PWR_SAVE |
......@@ -246,8 +249,8 @@ static int lp5523_configure(struct i2c_client *client)
return -1;
}
/* Wait 3ms and check the engine status */
usleep_range(3000, 20000);
/* Let the programs run for couple of ms and check the engine status */
usleep_range(3000, 6000);
lp5523_read(client, LP5523_REG_STATUS, &status);
status &= LP5523_ENG_STATUS_MASK;
......@@ -452,10 +455,10 @@ static ssize_t lp5523_selftest(struct device *dev,
/* Measure VDD (i.e. VBAT) first (channel 16 corresponds to VDD) */
lp5523_write(chip->client, LP5523_REG_LED_TEST_CTRL,
LP5523_EN_LEDTEST | 16);
usleep_range(3000, 10000);
usleep_range(3000, 6000); /* ADC conversion time is typically 2.7 ms */
ret = lp5523_read(chip->client, LP5523_REG_STATUS, &status);
if (!(status & LP5523_LEDTEST_DONE))
usleep_range(3000, 10000);
usleep_range(3000, 6000); /* Was not ready. Wait little bit */
ret |= lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &vdd);
vdd--; /* There may be some fluctuation in measurement */
......@@ -471,16 +474,16 @@ static ssize_t lp5523_selftest(struct device *dev,
chip->pdata->led_config[i].led_current);
lp5523_write(chip->client, LP5523_REG_LED_PWM_BASE + i, 0xff);
/* let current stabilize 2ms before measurements start */
usleep_range(2000, 10000);
/* let current stabilize 2 - 4ms before measurements start */
usleep_range(2000, 4000);
lp5523_write(chip->client,
LP5523_REG_LED_TEST_CTRL,
LP5523_EN_LEDTEST | i);
/* ledtest takes 2.7ms */
usleep_range(3000, 10000);
/* ADC conversion time is 2.7 ms typically */
usleep_range(3000, 6000);
ret = lp5523_read(chip->client, LP5523_REG_STATUS, &status);
if (!(status & LP5523_LEDTEST_DONE))
usleep_range(3000, 10000);
usleep_range(3000, 6000);/* Was not ready. Wait. */
ret |= lp5523_read(chip->client, LP5523_REG_LED_TEST_ADC, &adc);
if (adc >= vdd || adc < LP5523_ADC_SHORTCIRC_LIM)
......@@ -933,9 +936,9 @@ static int lp5523_probe(struct i2c_client *client,
if (pdata->enable) {
pdata->enable(0);
usleep_range(1000, 10000);
usleep_range(1000, 2000); /* Keep enable down at least 1ms */
pdata->enable(1);
usleep_range(1000, 10000); /* Spec says min 500us */
usleep_range(1000, 2000); /* 500us abs min. */
}
ret = lp5523_detect(client);
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment