3c59x.c

	if (dev && vp) {
		pci_set_power_state(pdev, PCI_D0);
		pci_restore_state(pdev);
		pci_enable_device(pdev);
		pci_set_master(pdev);
		if (request_irq(dev->irq, vp->full_bus_master_rx ?
				&boomerang_interrupt : &vortex_interrupt, SA_SHIRQ, dev->name, dev)) {
			printk(KERN_WARNING "%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
			pci_disable_device(pdev);
			return -EBUSY;
		}
		if (netif_running(dev)) {
			vortex_up(dev);
			netif_device_attach(dev);
		}
	}
	return 0;
}

#endif /* CONFIG_PM */

#ifdef CONFIG_EISA
static struct eisa_device_id vortex_eisa_ids[] = {
	{ "TCM5920", CH_3C592 },
	{ "TCM5970", CH_3C597 },
	{ "" }
};

static int vortex_eisa_probe (struct device *device);
static int vortex_eisa_remove (struct device *device);

static struct eisa_driver vortex_eisa_driver = {
	.id_table = vortex_eisa_ids,
	.driver   = {
		.name    = "3c59x",
		.probe   = vortex_eisa_probe,
		.remove  = vortex_eisa_remove
	}
};

static int vortex_eisa_probe (struct device *device)
{
	void __iomem *ioaddr;
	struct eisa_device *edev;

	edev = to_eisa_device (device);

	if (!request_region(edev->base_addr, VORTEX_TOTAL_SIZE, DRV_NAME))
		return -EBUSY;

	ioaddr = ioport_map(edev->base_addr, VORTEX_TOTAL_SIZE);

	if (vortex_probe1(device, ioaddr, ioread16(ioaddr + 0xC88) >> 12,
					  edev->id.driver_data, vortex_cards_found)) {
		release_region (edev->base_addr, VORTEX_TOTAL_SIZE);
		return -ENODEV;
	}

	vortex_cards_found++;

	return 0;
}

static int vortex_eisa_remove (struct device *device)
{
	struct eisa_device *edev;
	struct net_device *dev;
	struct vortex_private *vp;
	void __iomem *ioaddr;

	edev = to_eisa_device (device);
	dev = eisa_get_drvdata (edev);

	if (!dev) {
		printk("vortex_eisa_remove called for Compaq device!\n");
		BUG();
	}

	vp = netdev_priv(dev);
	ioaddr = vp->ioaddr;
	
	unregister_netdev (dev);
	iowrite16 (TotalReset|0x14, ioaddr + EL3_CMD);
	release_region (dev->base_addr, VORTEX_TOTAL_SIZE);

	free_netdev (dev);
	return 0;
}
#endif

/* returns count found (>= 0), or negative on error */
static int __init vortex_eisa_init (void)
{
	int eisa_found = 0;
	int orig_cards_found = vortex_cards_found;

#ifdef CONFIG_EISA
	if (eisa_driver_register (&vortex_eisa_driver) >= 0) {
			/* Because of the way EISA bus is probed, we cannot assume
			 * any device have been found when we exit from
			 * eisa_driver_register (the bus root driver may not be
			 * initialized yet). So we blindly assume something was
			 * found, and let the sysfs magic happend... */
			
			eisa_found = 1;
	}
#endif
	
	/* Special code to work-around the Compaq PCI BIOS32 problem. */
	if (compaq_ioaddr) {
		vortex_probe1(NULL, ioport_map(compaq_ioaddr, VORTEX_TOTAL_SIZE),
			      compaq_irq, compaq_device_id, vortex_cards_found++);
	}

	return vortex_cards_found - orig_cards_found + eisa_found;
}

/* returns count (>= 0), or negative on error */
static int __devinit vortex_init_one (struct pci_dev *pdev,
				      const struct pci_device_id *ent)
{
	int rc, unit, pci_bar;
	struct vortex_chip_info *vci;
	void __iomem *ioaddr;

	/* wake up and enable device */		
	rc = pci_enable_device (pdev);
	if (rc < 0)
		goto out;

	unit = vortex_cards_found;

	if (global_use_mmio < 0 && (unit >= MAX_UNITS || use_mmio[unit] < 0)) {
		/* Determine the default if the user didn't override us */
		vci = &vortex_info_tbl[ent->driver_data];
		pci_bar = vci->drv_flags & (IS_CYCLONE | IS_TORNADO) ? 1 : 0;
	} else if (unit < MAX_UNITS && use_mmio[unit] >= 0)
		pci_bar = use_mmio[unit] ? 1 : 0;
	else
		pci_bar = global_use_mmio ? 1 : 0;

	ioaddr = pci_iomap(pdev, pci_bar, 0);
	if (!ioaddr) /* If mapping fails, fall-back to BAR 0... */
		ioaddr = pci_iomap(pdev, 0, 0);

	rc = vortex_probe1(&pdev->dev, ioaddr, pdev->irq,
			   ent->driver_data, unit);
	if (rc < 0) {
		pci_disable_device (pdev);
		goto out;
	}

	vortex_cards_found++;

out:
	return rc;
}

/*
 * Start up the PCI/EISA device which is described by *gendev.
 * Return 0 on success.
 *
 * NOTE: pdev can be NULL, for the case of a Compaq device
 */
static int __devinit vortex_probe1(struct device *gendev,
				   void __iomem *ioaddr, int irq,
				   int chip_idx, int card_idx)
{
	struct vortex_private *vp;
	int option;
	unsigned int eeprom[0x40], checksum = 0;		/* EEPROM contents */
	int i, step;
	struct net_device *dev;
	static int printed_version;
	int retval, print_info;
	struct vortex_chip_info * const vci = &vortex_info_tbl[chip_idx];
	char *print_name = "3c59x";
	struct pci_dev *pdev = NULL;
	struct eisa_device *edev = NULL;

	if (!printed_version) {
		printk (version);
		printed_version = 1;
	}

	if (gendev) {
		if ((pdev = DEVICE_PCI(gendev))) {
			print_name = pci_name(pdev);
		}

		if ((edev = DEVICE_EISA(gendev))) {
			print_name = edev->dev.bus_id;
		}
	}

	dev = alloc_etherdev(sizeof(*vp));
	retval = -ENOMEM;
	if (!dev) {
		printk (KERN_ERR PFX "unable to allocate etherdev, aborting\n");
		goto out;
	}
	SET_MODULE_OWNER(dev);
	SET_NETDEV_DEV(dev, gendev);
	vp = netdev_priv(dev);

	option = global_options;

	/* The lower four bits are the media type. */
	if (dev->mem_start) {
		/*
		 * The 'options' param is passed in as the third arg to the
		 * LILO 'ether=' argument for non-modular use
		 */
		option = dev->mem_start;
	}
	else if (card_idx < MAX_UNITS) {
		if (options[card_idx] >= 0)
			option = options[card_idx];
	}

	if (option > 0) {
		if (option & 0x8000)
			vortex_debug = 7;
		if (option & 0x4000)
			vortex_debug = 2;
		if (option & 0x0400)
			vp->enable_wol = 1;
	}

	print_info = (vortex_debug > 1);
	if (print_info)
		printk (KERN_INFO "See Documentation/networking/vortex.txt\n");

	printk(KERN_INFO "%s: 3Com %s %s at %p. Vers " DRV_VERSION "\n",
	       print_name,
	       pdev ? "PCI" : "EISA",
	       vci->name,
	       ioaddr);

	dev->base_addr = (unsigned long)ioaddr;
	dev->irq = irq;
	dev->mtu = mtu;
	vp->ioaddr = ioaddr;
	vp->large_frames = mtu > 1500;
	vp->drv_flags = vci->drv_flags;
	vp->has_nway = (vci->drv_flags & HAS_NWAY) ? 1 : 0;
	vp->io_size = vci->io_size;
	vp->card_idx = card_idx;

	/* module list only for Compaq device */
	if (gendev == NULL) {
		compaq_net_device = dev;
	}

	/* PCI-only startup logic */
	if (pdev) {
		/* EISA resources already marked, so only PCI needs to do this here */
		/* Ignore return value, because Cardbus drivers already allocate for us */
		if (request_region(dev->base_addr, vci->io_size, print_name) != NULL)
			vp->must_free_region = 1;

		/* enable bus-mastering if necessary */		
		if (vci->flags & PCI_USES_MASTER)
			pci_set_master (pdev);

		if (vci->drv_flags & IS_VORTEX) {
			u8 pci_latency;
			u8 new_latency = 248;

			/* Check the PCI latency value.  On the 3c590 series the latency timer
			   must be set to the maximum value to avoid data corruption that occurs
			   when the timer expires during a transfer.  This bug exists the Vortex
			   chip only. */
			pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &pci_latency);
			if (pci_latency < new_latency) {
				printk(KERN_INFO "%s: Overriding PCI latency"
					" timer (CFLT) setting of %d, new value is %d.\n",
					print_name, pci_latency, new_latency);
					pci_write_config_byte(pdev, PCI_LATENCY_TIMER, new_latency);
			}
		}
	}

	spin_lock_init(&vp->lock);
	vp->gendev = gendev;
	vp->mii.dev = dev;
	vp->mii.mdio_read = mdio_read;
	vp->mii.mdio_write = mdio_write;
	vp->mii.phy_id_mask = 0x1f;
	vp->mii.reg_num_mask = 0x1f;

	/* Makes sure rings are at least 16 byte aligned. */
	vp->rx_ring = pci_alloc_consistent(pdev, sizeof(struct boom_rx_desc) * RX_RING_SIZE
					   + sizeof(struct boom_tx_desc) * TX_RING_SIZE,
					   &vp->rx_ring_dma);
	retval = -ENOMEM;
	if (vp->rx_ring == 0)
		goto free_region;

	vp->tx_ring = (struct boom_tx_desc *)(vp->rx_ring + RX_RING_SIZE);
	vp->tx_ring_dma = vp->rx_ring_dma + sizeof(struct boom_rx_desc) * RX_RING_SIZE;

	/* if we are a PCI driver, we store info in pdev->driver_data
	 * instead of a module list */	
	if (pdev)
		pci_set_drvdata(pdev, dev);
	if (edev)
		eisa_set_drvdata (edev, dev);

	vp->media_override = 7;
	if (option >= 0) {
		vp->media_override = ((option & 7) == 2)  ?  0  :  option & 15;
		if (vp->media_override != 7)
			vp->medialock = 1;
		vp->full_duplex = (option & 0x200) ? 1 : 0;
		vp->bus_master = (option & 16) ? 1 : 0;
	}

	if (global_full_duplex > 0)
		vp->full_duplex = 1;
	if (global_enable_wol > 0)
		vp->enable_wol = 1;

	if (card_idx < MAX_UNITS) {
		if (full_duplex[card_idx] > 0)
			vp->full_duplex = 1;
		if (flow_ctrl[card_idx] > 0)
			vp->flow_ctrl = 1;
		if (enable_wol[card_idx] > 0)
			vp->enable_wol = 1;
	}

	vp->force_fd = vp->full_duplex;
	vp->options = option;
	/* Read the station address from the EEPROM. */
	EL3WINDOW(0);
	{
		int base;

		if (vci->drv_flags & EEPROM_8BIT)
			base = 0x230;
		else if (vci->drv_flags & EEPROM_OFFSET)
			base = EEPROM_Read + 0x30;
		else
			base = EEPROM_Read;

		for (i = 0; i < 0x40; i++) {
			int timer;
			iowrite16(base + i, ioaddr + Wn0EepromCmd);
			/* Pause for at least 162 us. for the read to take place. */
			for (timer = 10; timer >= 0; timer--) {
				udelay(162);
				if ((ioread16(ioaddr + Wn0EepromCmd) & 0x8000) == 0)
					break;
			}
			eeprom[i] = ioread16(ioaddr + Wn0EepromData);
		}
	}
	for (i = 0; i < 0x18; i++)
		checksum ^= eeprom[i];
	checksum = (checksum ^ (checksum >> 8)) & 0xff;
	if (checksum != 0x00) {		/* Grrr, needless incompatible change 3Com. */
		while (i < 0x21)
			checksum ^= eeprom[i++];
		checksum = (checksum ^ (checksum >> 8)) & 0xff;
	}
	if ((checksum != 0x00) && !(vci->drv_flags & IS_TORNADO))
		printk(" ***INVALID CHECKSUM %4.4x*** ", checksum);
	for (i = 0; i < 3; i++)
		((u16 *)dev->dev_addr)[i] = htons(eeprom[i + 10]);
	memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
	if (print_info) {
		for (i = 0; i < 6; i++)
			printk("%c%2.2x", i ? ':' : ' ', dev->dev_addr[i]);
	}
	/* Unfortunately an all zero eeprom passes the checksum and this
	   gets found in the wild in failure cases. Crypto is hard 8) */
	if (!is_valid_ether_addr(dev->dev_addr)) {
		retval = -EINVAL;
		printk(KERN_ERR "*** EEPROM MAC address is invalid.\n");
		goto free_ring;	/* With every pack */
	}
	EL3WINDOW(2);
	for (i = 0; i < 6; i++)
		iowrite8(dev->dev_addr[i], ioaddr + i);

#ifdef __sparc__
	if (print_info)
		printk(", IRQ %s\n", __irq_itoa(dev->irq));
#else
	if (print_info)
		printk(", IRQ %d\n", dev->irq);
	/* Tell them about an invalid IRQ. */
	if (dev->irq <= 0 || dev->irq >= NR_IRQS)
		printk(KERN_WARNING " *** Warning: IRQ %d is unlikely to work! ***\n",
			   dev->irq);
#endif

	EL3WINDOW(4);
	step = (ioread8(ioaddr + Wn4_NetDiag) & 0x1e) >> 1;
	if (print_info) {
		printk(KERN_INFO "  product code %02x%02x rev %02x.%d date %02d-"
			"%02d-%02d\n", eeprom[6]&0xff, eeprom[6]>>8, eeprom[0x14],
			step, (eeprom[4]>>5) & 15, eeprom[4] & 31, eeprom[4]>>9);
	}


	if (pdev && vci->drv_flags & HAS_CB_FNS) {
		unsigned short n;

		vp->cb_fn_base = pci_iomap(pdev, 2, 0);
		if (!vp->cb_fn_base) {
			retval = -ENOMEM;
			goto free_ring;
		}

		if (print_info) {
			printk(KERN_INFO "%s: CardBus functions mapped %8.8lx->%p\n",
				print_name, pci_resource_start(pdev, 2),
				vp->cb_fn_base);
		}
		EL3WINDOW(2);

		n = ioread16(ioaddr + Wn2_ResetOptions) & ~0x4010;
		if (vp->drv_flags & INVERT_LED_PWR)
			n |= 0x10;
		if (vp->drv_flags & INVERT_MII_PWR)
			n |= 0x4000;
		iowrite16(n, ioaddr + Wn2_ResetOptions);
		if (vp->drv_flags & WNO_XCVR_PWR) {
			EL3WINDOW(0);
			iowrite16(0x0800, ioaddr);
		}
	}

	/* Extract our information from the EEPROM data. */
	vp->info1 = eeprom[13];
	vp->info2 = eeprom[15];
	vp->capabilities = eeprom[16];

	if (vp->info1 & 0x8000) {
		vp->full_duplex = 1;
		if (print_info)
			printk(KERN_INFO "Full duplex capable\n");
	}

	{
		static const char * ram_split[] = {"5:3", "3:1", "1:1", "3:5"};
		unsigned int config;
		EL3WINDOW(3);
		vp->available_media = ioread16(ioaddr + Wn3_Options);
		if ((vp->available_media & 0xff) == 0)		/* Broken 3c916 */
			vp->available_media = 0x40;
		config = ioread32(ioaddr + Wn3_Config);
		if (print_info) {
			printk(KERN_DEBUG "  Internal config register is %4.4x, "
				   "transceivers %#x.\n", config, ioread16(ioaddr + Wn3_Options));
			printk(KERN_INFO "  %dK %s-wide RAM %s Rx:Tx split, %s%s interface.\n",
				   8 << RAM_SIZE(config),
				   RAM_WIDTH(config) ? "word" : "byte",
				   ram_split[RAM_SPLIT(config)],
				   AUTOSELECT(config) ? "autoselect/" : "",
				   XCVR(config) > XCVR_ExtMII ? "<invalid transceiver>" :
				   media_tbl[XCVR(config)].name);
		}
		vp->default_media = XCVR(config);
		if (vp->default_media == XCVR_NWAY)
			vp->has_nway = 1;
		vp->autoselect = AUTOSELECT(config);
	}

	if (vp->media_override != 7) {
		printk(KERN_INFO "%s:  Media override to transceiver type %d (%s).\n",
				print_name, vp->media_override,
				media_tbl[vp->media_override].name);
		dev->if_port = vp->media_override;
	} else
		dev->if_port = vp->default_media;

	if ((vp->available_media & 0x40) || (vci->drv_flags & HAS_NWAY) ||
		dev->if_port == XCVR_MII || dev->if_port == XCVR_NWAY) {
		int phy, phy_idx = 0;
		EL3WINDOW(4);
		mii_preamble_required++;
		if (vp->drv_flags & EXTRA_PREAMBLE)
			mii_preamble_required++;
		mdio_sync(ioaddr, 32);
		mdio_read(dev, 24, MII_BMSR);
		for (phy = 0; phy < 32 && phy_idx < 1; phy++) {
			int mii_status, phyx;

			/*
			 * For the 3c905CX we look at index 24 first, because it bogusly
			 * reports an external PHY at all indices
			 */
			if (phy == 0)
				phyx = 24;
			else if (phy <= 24)
				phyx = phy - 1;
			else
				phyx = phy;
			mii_status = mdio_read(dev, phyx, MII_BMSR);
			if (mii_status  &&  mii_status != 0xffff) {
				vp->phys[phy_idx++] = phyx;
				if (print_info) {
					printk(KERN_INFO "  MII transceiver found at address %d,"
						" status %4x.\n", phyx, mii_status);
				}
				if ((mii_status & 0x0040) == 0)
					mii_preamble_required++;
			}
		}
		mii_preamble_required--;
		if (phy_idx == 0) {
			printk(KERN_WARNING"  ***WARNING*** No MII transceivers found!\n");
			vp->phys[0] = 24;
		} else {
			vp->advertising = mdio_read(dev, vp->phys[0], MII_ADVERTISE);
			if (vp->full_duplex) {
				/* Only advertise the FD media types. */
				vp->advertising &= ~0x02A0;
				mdio_write(dev, vp->phys[0], 4, vp->advertising);
			}
		}
		vp->mii.phy_id = vp->phys[0];
	}

	if (vp->capabilities & CapBusMaster) {
		vp->full_bus_master_tx = 1;
		if (print_info) {
			printk(KERN_INFO "  Enabling bus-master transmits and %s receives.\n",
			(vp->info2 & 1) ? "early" : "whole-frame" );
		}
		vp->full_bus_master_rx = (vp->info2 & 1) ? 1 : 2;
		vp->bus_master = 0;		/* AKPM: vortex only */
	}

	/* The 3c59x-specific entries in the device structure. */
	dev->open = vortex_open;
	if (vp->full_bus_master_tx) {
		dev->hard_start_xmit = boomerang_start_xmit;
		/* Actually, it still should work with iommu. */
		if (card_idx < MAX_UNITS &&
		    ((hw_checksums[card_idx] == -1 && (vp->drv_flags & HAS_HWCKSM)) ||
				hw_checksums[card_idx] == 1)) {
			dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
		}
	} else {
		dev->hard_start_xmit = vortex_start_xmit;
	}

	if (print_info) {
		printk(KERN_INFO "%s: scatter/gather %sabled. h/w checksums %sabled\n",
				print_name,
				(dev->features & NETIF_F_SG) ? "en":"dis",
				(dev->features & NETIF_F_IP_CSUM) ? "en":"dis");
	}

	dev->stop = vortex_close;
	dev->get_stats = vortex_get_stats;
#ifdef CONFIG_PCI
	dev->do_ioctl = vortex_ioctl;
#endif
	dev->ethtool_ops = &vortex_ethtool_ops;
	dev->set_multicast_list = set_rx_mode;
	dev->tx_timeout = vortex_tx_timeout;
	dev->watchdog_timeo = (watchdog * HZ) / 1000;
#ifdef CONFIG_NET_POLL_CONTROLLER
	dev->poll_controller = poll_vortex; 
#endif
	if (pdev) {
		vp->pm_state_valid = 1;
 		pci_save_state(VORTEX_PCI(vp));
 		acpi_set_WOL(dev);
	}
	retval = register_netdev(dev);
	if (retval == 0)
		return 0;

free_ring:
	pci_free_consistent(pdev,
						sizeof(struct boom_rx_desc) * RX_RING_SIZE
							+ sizeof(struct boom_tx_desc) * TX_RING_SIZE,
						vp->rx_ring,
						vp->rx_ring_dma);
free_region:
	if (vp->must_free_region)
		release_region(dev->base_addr, vci->io_size);
	free_netdev(dev);
	printk(KERN_ERR PFX "vortex_probe1 fails.  Returns %d\n", retval);
out:
	return retval;
}

static void
issue_and_wait(struct net_device *dev, int cmd)
{
	struct vortex_private *vp = netdev_priv(dev);
	void __iomem *ioaddr = vp->ioaddr;
	int i;

	iowrite16(cmd, ioaddr + EL3_CMD);
	for (i = 0; i < 2000; i++) {
		if (!(ioread16(ioaddr + EL3_STATUS) & CmdInProgress))
			return;
	}

	/* OK, that didn't work.  Do it the slow way.  One second */
	for (i = 0; i < 100000; i++) {
		if (!(ioread16(ioaddr + EL3_STATUS) & CmdInProgress)) {
			if (vortex_debug > 1)
				printk(KERN_INFO "%s: command 0x%04x took %d usecs\n",
					   dev->name, cmd, i * 10);
			return;
		}
		udelay(10);
	}
	printk(KERN_ERR "%s: command 0x%04x did not complete! Status=0x%x\n",
			   dev->name, cmd, ioread16(ioaddr + EL3_STATUS));
}

static void
vortex_up(struct net_device *dev)
{
	struct vortex_private *vp = netdev_priv(dev);
	void __iomem *ioaddr = vp->ioaddr;
	unsigned int config;
	int i;

	if (VORTEX_PCI(vp)) {
		pci_set_power_state(VORTEX_PCI(vp), PCI_D0);	/* Go active */
		if (vp->pm_state_valid)
			pci_restore_state(VORTEX_PCI(vp));
		pci_enable_device(VORTEX_PCI(vp));
	}

	/* Before initializing select the active media port. */
	EL3WINDOW(3);
	config = ioread32(ioaddr + Wn3_Config);

	if (vp->media_override != 7) {
		printk(KERN_INFO "%s: Media override to transceiver %d (%s).\n",
			   dev->name, vp->media_override,
			   media_tbl[vp->media_override].name);
		dev->if_port = vp->media_override;
	} else if (vp->autoselect) {
		if (vp->has_nway) {
			if (vortex_debug > 1)
				printk(KERN_INFO "%s: using NWAY device table, not %d\n",
								dev->name, dev->if_port);
			dev->if_port = XCVR_NWAY;
		} else {
			/* Find first available media type, starting with 100baseTx. */
			dev->if_port = XCVR_100baseTx;
			while (! (vp->available_media & media_tbl[dev->if_port].mask))
				dev->if_port = media_tbl[dev->if_port].next;
			if (vortex_debug > 1)
				printk(KERN_INFO "%s: first available media type: %s\n",
					dev->name, media_tbl[dev->if_port].name);
		}
	} else {
		dev->if_port = vp->default_media;
		if (vortex_debug > 1)
			printk(KERN_INFO "%s: using default media %s\n",
				dev->name, media_tbl[dev->if_port].name);
	}

	init_timer(&vp->timer);
	vp->timer.expires = RUN_AT(media_tbl[dev->if_port].wait);
	vp->timer.data = (unsigned long)dev;
	vp->timer.function = vortex_timer;		/* timer handler */
	add_timer(&vp->timer);

	init_timer(&vp->rx_oom_timer);
	vp->rx_oom_timer.data = (unsigned long)dev;
	vp->rx_oom_timer.function = rx_oom_timer;

	if (vortex_debug > 1)
		printk(KERN_DEBUG "%s: Initial media type %s.\n",
			   dev->name, media_tbl[dev->if_port].name);

	vp->full_duplex = vp->force_fd;
	config = BFINS(config, dev->if_port, 20, 4);
	if (vortex_debug > 6)
		printk(KERN_DEBUG "vortex_up(): writing 0x%x to InternalConfig\n", config);
	iowrite32(config, ioaddr + Wn3_Config);

	if (dev->if_port == XCVR_MII || dev->if_port == XCVR_NWAY) {
		int mii_reg1, mii_reg5;
		EL3WINDOW(4);
		/* Read BMSR (reg1) only to clear old status. */
		mii_reg1 = mdio_read(dev, vp->phys[0], MII_BMSR);
		mii_reg5 = mdio_read(dev, vp->phys[0], MII_LPA);
		if (mii_reg5 == 0xffff  ||  mii_reg5 == 0x0000) {
			netif_carrier_off(dev); /* No MII device or no link partner report */
		} else {
			mii_reg5 &= vp->advertising;
			if ((mii_reg5 & 0x0100) != 0	/* 100baseTx-FD */
				 || (mii_reg5 & 0x00C0) == 0x0040) /* 10T-FD, but not 100-HD */
			vp->full_duplex = 1;
			netif_carrier_on(dev);
		}
		vp->partner_flow_ctrl = ((mii_reg5 & 0x0400) != 0);
		if (vortex_debug > 1)
			printk(KERN_INFO "%s: MII #%d status %4.4x, link partner capability %4.4x,"
				   " info1 %04x, setting %s-duplex.\n",
					dev->name, vp->phys[0],
					mii_reg1, mii_reg5,
					vp->info1, ((vp->info1 & 0x8000) || vp->full_duplex) ? "full" : "half");
		EL3WINDOW(3);
	}

	/* Set the full-duplex bit. */
	iowrite16(	((vp->info1 & 0x8000) || vp->full_duplex ? 0x20 : 0) |
		 	(vp->large_frames ? 0x40 : 0) |
			((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
			ioaddr + Wn3_MAC_Ctrl);

	if (vortex_debug > 1) {
		printk(KERN_DEBUG "%s: vortex_up() InternalConfig %8.8x.\n",
			dev->name, config);
	}

	issue_and_wait(dev, TxReset);
	/*
	 * Don't reset the PHY - that upsets autonegotiation during DHCP operations.
	 */
	issue_and_wait(dev, RxReset|0x04);

	iowrite16(SetStatusEnb | 0x00, ioaddr + EL3_CMD);

	if (vortex_debug > 1) {
		EL3WINDOW(4);
		printk(KERN_DEBUG "%s: vortex_up() irq %d media status %4.4x.\n",
			   dev->name, dev->irq, ioread16(ioaddr + Wn4_Media));
	}

	/* Set the station address and mask in window 2 each time opened. */
	EL3WINDOW(2);
	for (i = 0; i < 6; i++)
		iowrite8(dev->dev_addr[i], ioaddr + i);
	for (; i < 12; i+=2)
		iowrite16(0, ioaddr + i);

	if (vp->cb_fn_base) {
		unsigned short n = ioread16(ioaddr + Wn2_ResetOptions) & ~0x4010;
		if (vp->drv_flags & INVERT_LED_PWR)
			n |= 0x10;
		if (vp->drv_flags & INVERT_MII_PWR)
			n |= 0x4000;
		iowrite16(n, ioaddr + Wn2_ResetOptions);
	}

	if (dev->if_port == XCVR_10base2)
		/* Start the thinnet transceiver. We should really wait 50ms...*/
		iowrite16(StartCoax, ioaddr + EL3_CMD);
	if (dev->if_port != XCVR_NWAY) {
		EL3WINDOW(4);
		iowrite16((ioread16(ioaddr + Wn4_Media) & ~(Media_10TP|Media_SQE)) |
			 media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
	}

	/* Switch to the stats window, and clear all stats by reading. */
	iowrite16(StatsDisable, ioaddr + EL3_CMD);
	EL3WINDOW(6);
	for (i = 0; i < 10; i++)
		ioread8(ioaddr + i);
	ioread16(ioaddr + 10);
	ioread16(ioaddr + 12);
	/* New: On the Vortex we must also clear the BadSSD counter. */
	EL3WINDOW(4);
	ioread8(ioaddr + 12);
	/* ..and on the Boomerang we enable the extra statistics bits. */
	iowrite16(0x0040, ioaddr + Wn4_NetDiag);

	/* Switch to register set 7 for normal use. */
	EL3WINDOW(7);

	if (vp->full_bus_master_rx) { /* Boomerang bus master. */
		vp->cur_rx = vp->dirty_rx = 0;
		/* Initialize the RxEarly register as recommended. */
		iowrite16(SetRxThreshold + (1536>>2), ioaddr + EL3_CMD);
		iowrite32(0x0020, ioaddr + PktStatus);
		iowrite32(vp->rx_ring_dma, ioaddr + UpListPtr);
	}
	if (vp->full_bus_master_tx) { 		/* Boomerang bus master Tx. */
		vp->cur_tx = vp->dirty_tx = 0;
		if (vp->drv_flags & IS_BOOMERANG)
			iowrite8(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold); /* Room for a packet. */
		/* Clear the Rx, Tx rings. */
		for (i = 0; i < RX_RING_SIZE; i++)	/* AKPM: this is done in vortex_open, too */
			vp->rx_ring[i].status = 0;
		for (i = 0; i < TX_RING_SIZE; i++)
			vp->tx_skbuff[i] = NULL;
		iowrite32(0, ioaddr + DownListPtr);
	}
	/* Set receiver mode: presumably accept b-case and phys addr only. */
	set_rx_mode(dev);
	/* enable 802.1q tagged frames */
	set_8021q_mode(dev, 1);
	iowrite16(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */

//	issue_and_wait(dev, SetTxStart|0x07ff);
	iowrite16(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
	iowrite16(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
	/* Allow status bits to be seen. */
	vp->status_enable = SetStatusEnb | HostError|IntReq|StatsFull|TxComplete|
		(vp->full_bus_master_tx ? DownComplete : TxAvailable) |
		(vp->full_bus_master_rx ? UpComplete : RxComplete) |
		(vp->bus_master ? DMADone : 0);
	vp->intr_enable = SetIntrEnb | IntLatch | TxAvailable |
		(vp->full_bus_master_rx ? 0 : RxComplete) |
		StatsFull | HostError | TxComplete | IntReq
		| (vp->bus_master ? DMADone : 0) | UpComplete | DownComplete;
	iowrite16(vp->status_enable, ioaddr + EL3_CMD);
	/* Ack all pending events, and set active indicator mask. */
	iowrite16(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
		 ioaddr + EL3_CMD);
	iowrite16(vp->intr_enable, ioaddr + EL3_CMD);
	if (vp->cb_fn_base)			/* The PCMCIA people are idiots.  */
		iowrite32(0x8000, vp->cb_fn_base + 4);
	netif_start_queue (dev);
}

static int
vortex_open(struct net_device *dev)
{
	struct vortex_private *vp = netdev_priv(dev);
	int i;
	int retval;

	/* Use the now-standard shared IRQ implementation. */
	if ((retval = request_irq(dev->irq, vp->full_bus_master_rx ?
				&boomerang_interrupt : &vortex_interrupt, SA_SHIRQ, dev->name, dev))) {
		printk(KERN_ERR "%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
		goto out;
	}

	if (vp->full_bus_master_rx) { /* Boomerang bus master. */
		if (vortex_debug > 2)
			printk(KERN_DEBUG "%s:  Filling in the Rx ring.\n", dev->name);
		for (i = 0; i < RX_RING_SIZE; i++) {
			struct sk_buff *skb;
			vp->rx_ring[i].next = cpu_to_le32(vp->rx_ring_dma + sizeof(struct boom_rx_desc) * (i+1));
			vp->rx_ring[i].status = 0;	/* Clear complete bit. */
			vp->rx_ring[i].length = cpu_to_le32(PKT_BUF_SZ | LAST_FRAG);
			skb = dev_alloc_skb(PKT_BUF_SZ);
			vp->rx_skbuff[i] = skb;
			if (skb == NULL)
				break;			/* Bad news!  */
			skb->dev = dev;			/* Mark as being used by this device. */
			skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
			vp->rx_ring[i].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, PKT_BUF_SZ, PCI_DMA_FROMDEVICE));
		}
		if (i != RX_RING_SIZE) {
			int j;
			printk(KERN_EMERG "%s: no memory for rx ring\n", dev->name);
			for (j = 0; j < i; j++) {
				if (vp->rx_skbuff[j]) {
					dev_kfree_skb(vp->rx_skbuff[j]);
					vp->rx_skbuff[j] = NULL;
				}
			}
			retval = -ENOMEM;
			goto out_free_irq;
		}
		/* Wrap the ring. */
		vp->rx_ring[i-1].next = cpu_to_le32(vp->rx_ring_dma);
	}

	vortex_up(dev);
	return 0;

out_free_irq:
	free_irq(dev->irq, dev);
out:
	if (vortex_debug > 1)
		printk(KERN_ERR "%s: vortex_open() fails: returning %d\n", dev->name, retval);
	return retval;
}

static void
vortex_timer(unsigned long data)
{
	struct net_device *dev = (struct net_device *)data;
	struct vortex_private *vp = netdev_priv(dev);
	void __iomem *ioaddr = vp->ioaddr;
	int next_tick = 60*HZ;
	int ok = 0;
	int media_status, mii_status, old_window;

	if (vortex_debug > 2) {
		printk(KERN_DEBUG "%s: Media selection timer tick happened, %s.\n",
			   dev->name, media_tbl[dev->if_port].name);
		printk(KERN_DEBUG "dev->watchdog_timeo=%d\n", dev->watchdog_timeo);
	}

	if (vp->medialock)
		goto leave_media_alone;
	disable_irq(dev->irq);
	old_window = ioread16(ioaddr + EL3_CMD) >> 13;
	EL3WINDOW(4);
	media_status = ioread16(ioaddr + Wn4_Media);
	switch (dev->if_port) {
	case XCVR_10baseT:  case XCVR_100baseTx:  case XCVR_100baseFx:
		if (media_status & Media_LnkBeat) {
			netif_carrier_on(dev);
			ok = 1;
			if (vortex_debug > 1)
				printk(KERN_DEBUG "%s: Media %s has link beat, %x.\n",
					   dev->name, media_tbl[dev->if_port].name, media_status);
		} else {
			netif_carrier_off(dev);
			if (vortex_debug > 1) {
				printk(KERN_DEBUG "%s: Media %s has no link beat, %x.\n",
					   dev->name, media_tbl[dev->if_port].name, media_status);
			}
		}
		break;
	case XCVR_MII: case XCVR_NWAY:
		{
			spin_lock_bh(&vp->lock);
			mii_status = mdio_read(dev, vp->phys[0], MII_BMSR);
			if (!(mii_status & BMSR_LSTATUS)) {
				/* Re-read to get actual link status */
				mii_status = mdio_read(dev, vp->phys[0], MII_BMSR);
			}
			ok = 1;
			if (vortex_debug > 2)
				printk(KERN_DEBUG "%s: MII transceiver has status %4.4x.\n",
					dev->name, mii_status);
			if (mii_status & BMSR_LSTATUS) {
				int mii_reg5 = mdio_read(dev, vp->phys[0], MII_LPA);
				if (! vp->force_fd  &&  mii_reg5 != 0xffff) {
					int duplex;

					mii_reg5 &= vp->advertising;
					duplex = (mii_reg5&0x0100) || (mii_reg5 & 0x01C0) == 0x0040;
					if (vp->full_duplex != duplex) {
						vp->full_duplex = duplex;
						printk(KERN_INFO "%s: Setting %s-duplex based on MII "
							"#%d link partner capability of %4.4x.\n",
							dev->name, vp->full_duplex ? "full" : "half",
							vp->phys[0], mii_reg5);
						/* Set the full-duplex bit. */
						EL3WINDOW(3);
						iowrite16(	(vp->full_duplex ? 0x20 : 0) |
								(vp->large_frames ? 0x40 : 0) |
								((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
								ioaddr + Wn3_MAC_Ctrl);
						if (vortex_debug > 1)
							printk(KERN_DEBUG "Setting duplex in Wn3_MAC_Ctrl\n");
						/* AKPM: bug: should reset Tx and Rx after setting Duplex.  Page 180 */
					}
				}
				netif_carrier_on(dev);
			} else {
				netif_carrier_off(dev);
			}
			spin_unlock_bh(&vp->lock);
		}
		break;
	  default:					/* Other media types handled by Tx timeouts. */
		if (vortex_debug > 1)
		  printk(KERN_DEBUG "%s: Media %s has no indication, %x.\n",
				 dev->name, media_tbl[dev->if_port].name, media_status);
		ok = 1;
	}
	if ( ! ok) {
		unsigned int config;

		do {
			dev->if_port = media_tbl[dev->if_port].next;
		} while ( ! (vp->available_media & media_tbl[dev->if_port].mask));
		if (dev->if_port == XCVR_Default) { /* Go back to default. */
		  dev->if_port = vp->default_media;
		  if (vortex_debug > 1)
			printk(KERN_DEBUG "%s: Media selection failing, using default "
				   "%s port.\n",
				   dev->name, media_tbl[dev->if_port].name);
		} else {
			if (vortex_debug > 1)
				printk(KERN_DEBUG "%s: Media selection failed, now trying "
					   "%s port.\n",
					   dev->name, media_tbl[dev->if_port].name);
			next_tick = media_tbl[dev->if_port].wait;
		}
		iowrite16((media_status & ~(Media_10TP|Media_SQE)) |
			 media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);

		EL3WINDOW(3);
		config = ioread32(ioaddr + Wn3_Config);
		config = BFINS(config, dev->if_port, 20, 4);
		iowrite32(config, ioaddr + Wn3_Config);

		iowrite16(dev->if_port == XCVR_10base2 ? StartCoax : StopCoax,
			 ioaddr + EL3_CMD);
		if (vortex_debug > 1)
			printk(KERN_DEBUG "wrote 0x%08x to Wn3_Config\n", config);
		/* AKPM: FIXME: Should reset Rx & Tx here.  P60 of 3c90xc.pdf */