Kconfig

	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ewrk3.

config EEXPRESS
	tristate "EtherExpress 16 support"
	depends on NET_ISA
	---help---
	  If you have an EtherExpress16 network (Ethernet) card, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Note that the Intel
	  EtherExpress16 card used to be regarded as a very poor choice
	  because the driver was very unreliable. We now have a new driver
	  that should do better.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called eexpress.

config EEXPRESS_PRO
	tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
	depends on NET_ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y. This
	  driver supports intel i82595{FX,TX} based boards. Note however
	  that the EtherExpress PRO/100 Ethernet card has its own separate
	  driver.  Please read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called eepro.

config HPLAN_PLUS
	tristate "HP PCLAN+ (27247B and 27252A) support"
	depends on NET_ISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called hp-plus.

config HPLAN
	tristate "HP PCLAN (27245 and other 27xxx series) support"
	depends on NET_ISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called hp.

config LP486E
	tristate "LP486E on board Ethernet"
	depends on NET_ISA
	help
	  Say Y here to support the 82596-based on-board Ethernet controller
	  for the Panther motherboard, which is one of the two shipped in the
	  Intel Professional Workstation.

config ETH16I
	tristate "ICL EtherTeam 16i/32 support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called eth16i.

config NE2000
	tristate "NE2000/NE1000 support"
	depends on NET_ISA || (Q40 && m) || M32R
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Many Ethernet cards
	  without a specific driver are compatible with NE2000.

	  If you have a PCI NE2000 card however, say N here and Y to "PCI
	  NE2000 support", above. If you have a NE2000 card and are running on
	  an MCA system (a bus system used on some IBM PS/2 computers and
	  laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
	  below.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ne.

config ZNET
	tristate "Zenith Z-Note support (EXPERIMENTAL)"
	depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
	help
	  The Zenith Z-Note notebook computer has a built-in network
	  (Ethernet) card, and this is the Linux driver for it. Note that the
	  IBM Thinkpad 300 is compatible with the Z-Note and is also supported
	  by this driver. Read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config SEEQ8005
	tristate "SEEQ8005 support (EXPERIMENTAL)"
	depends on NET_ISA && EXPERIMENTAL
	help
	  This is a driver for the SEEQ 8005 network (Ethernet) card.  If this
	  is for you, read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called seeq8005.

config SKMC
	tristate "SKnet MCA support"
	depends on NET_ETHERNET && MCA && BROKEN
	---help---
	  These are Micro Channel Ethernet adapters. You need to say Y to "MCA
	  support" in order to use this driver.  Supported cards are the SKnet
	  Junior MC2 and the SKnet MC2(+).  The driver automatically
	  distinguishes between the two cards. Note that using multiple boards
	  of different type hasn't been tested with this driver.  Say Y if you
	  have one of these Ethernet adapters.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called sk_mca.

config NE2_MCA
	tristate "NE/2 (ne2000 MCA version) support"
	depends on NET_ETHERNET && MCA_LEGACY
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ne2.

config IBMLANA
	tristate "IBM LAN Adapter/A support"
	depends on NET_ETHERNET && MCA && MCA_LEGACY
	---help---
	  This is a Micro Channel Ethernet adapter.  You need to set
	  CONFIG_MCA to use this driver.  It is both available as an in-kernel
	  driver and as a module.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The only
	  currently supported card is the IBM LAN Adapter/A for Ethernet.  It
	  will both support 16K and 32K memory windows, however a 32K window
	  gives a better security against packet losses.  Usage of multiple
	  boards with this driver should be possible, but has not been tested
	  up to now due to lack of hardware.

config IBMVETH
	tristate "IBM LAN Virtual Ethernet support"
	depends on NET_ETHERNET && PPC_PSERIES
	---help---
	  This driver supports virtual ethernet adapters on newer IBM iSeries
	  and pSeries systems.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module will
	  be called ibmveth.

config IBM_EMAC
	tristate "PowerPC 4xx on-chip Ethernet support"
	depends on 4xx
	help
	  This driver supports the PowerPC 4xx EMAC family of on-chip
          Ethernet controllers.

config IBM_EMAC_RXB
	int "Number of receive buffers"
	depends on IBM_EMAC
	default "128"

config IBM_EMAC_TXB
	int "Number of transmit buffers"
	depends on IBM_EMAC
	default "64"

config IBM_EMAC_POLL_WEIGHT
	int "MAL NAPI polling weight"
	depends on IBM_EMAC
	default "32"

config IBM_EMAC_RX_COPY_THRESHOLD
	int "RX skb copy threshold (bytes)"
	depends on IBM_EMAC
	default "256"

config IBM_EMAC_RX_SKB_HEADROOM
	int "Additional RX skb headroom (bytes)"
	depends on IBM_EMAC
	default "0"
	help
	  Additional receive skb headroom. Note, that driver
	  will always reserve at least 2 bytes to make IP header
	  aligned, so usualy there is no need to add any additional
	  headroom.
	  
	  If unsure, set to 0.

config IBM_EMAC_PHY_RX_CLK_FIX
	bool "PHY Rx clock workaround"
	depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
	help
	  Enable this if EMAC attached to a PHY which doesn't generate
	  RX clock if there is no link, if this is the case, you will 
	  see "TX disable timeout" or "RX disable timeout" in the system
	  log.
	  
	  If unsure, say N.

config IBM_EMAC_DEBUG
	bool "Debugging"
	depends on IBM_EMAC
	default n

config IBM_EMAC_ZMII
	bool
	depends on IBM_EMAC && (NP405H || NP405L || 44x)
	default y

config IBM_EMAC_RGMII
	bool
	depends on IBM_EMAC && 440GX
	default y
		
config IBM_EMAC_TAH
	bool
	depends on IBM_EMAC && 440GX
	default y

config NET_PCI
	bool "EISA, VLB, PCI and on board controllers"
	depends on NET_ETHERNET && (ISA || EISA || PCI)
	help
	  This is another class of network cards which attach directly to the
	  bus. If you have one of those, say Y and read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network cards. If you say Y, you
	  will be asked for your specific card in the following questions. If
	  you are unsure, say Y.

config PCNET32
	tristate "AMD PCnet32 PCI support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
	  answer Y here and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called pcnet32.

config AMD8111_ETH
	tristate "AMD 8111 (new PCI lance) support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  If you have an AMD 8111-based PCI lance ethernet card,
	  answer Y here and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called amd8111e.
config AMD8111E_NAPI
	bool "Enable NAPI support"
	depends on AMD8111_ETH
	help
	  NAPI is a new driver API designed to reduce CPU and interrupt load
	  when the driver is receiving lots of packets from the card. It is
	  still somewhat experimental and thus not yet enabled by default.

	  If your estimated Rx load is 10kpps or more, or if the card will be
	  deployed on potentially unfriendly networks (e.g. in a firewall),
	  then say Y here.

	  See <file:Documentation/networking/NAPI_HOWTO.txt> for more
	  information.

	  If in doubt, say N.

config ADAPTEC_STARFIRE
	tristate "Adaptec Starfire/DuraLAN support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
	  adapter. The DuraLAN chip is used on the 64 bit PCI boards from
	  Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
	  driver.

	  To compile this driver as a module, choose M here: the module
	  will be called starfire.  This is recommended.

config ADAPTEC_STARFIRE_NAPI
	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
	depends on ADAPTEC_STARFIRE && EXPERIMENTAL
	help
	  NAPI is a new driver API designed to reduce CPU and interrupt load
	  when the driver is receiving lots of packets from the card. It is
	  still somewhat experimental and thus not yet enabled by default.

	  If your estimated Rx load is 10kpps or more, or if the card will be
	  deployed on potentially unfriendly networks (e.g. in a firewall),
	  then say Y here.

	  See <file:Documentation/networking/NAPI_HOWTO.txt> for more
	  information.

	  If in doubt, say N.

config AC3200
	tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
	depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ac3200.

config APRICOT
	tristate "Apricot Xen-II on board Ethernet"
	depends on NET_PCI && ISA
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called apricot.

config B44
	tristate "Broadcom 4400 ethernet support (EXPERIMENTAL)"
	depends on NET_PCI && PCI && EXPERIMENTAL
	select MII
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called b44.

config FORCEDETH
	tristate "Reverse Engineered nForce Ethernet support (EXPERIMENTAL)"
	depends on NET_PCI && PCI && EXPERIMENTAL
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called forcedeth.


config CS89x0
	tristate "CS89x0 support"
	depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
	---help---
	  Support for CS89x0 chipset based Ethernet cards. If you have a
	  network (Ethernet) card of this type, say Y and read the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto> as well as
	  <file:Documentation/networking/cs89x0.txt>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called cs89x0.

config TC35815
	tristate "TOSHIBA TC35815 Ethernet support"
	depends on NET_PCI && PCI && TOSHIBA_JMR3927

config DGRS
	tristate "Digi Intl. RightSwitch SE-X support"
	depends on NET_PCI && (PCI || EISA)
	---help---
	  This is support for the Digi International RightSwitch series of
	  PCI/EISA Ethernet switch cards. These include the SE-4 and the SE-6
	  models.  If you have a network card of this type, say Y and read the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  More specific
	  information is contained in <file:Documentation/networking/dgrs.txt>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called dgrs.

config EEPRO100
	tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
	depends on NET_PCI && PCI
	select MII
	help
	  If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
	  card, say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called eepro100.


config E100
	tristate "Intel(R) PRO/100+ support"
	depends on NET_PCI && PCI
	select MII
	---help---
	  This driver supports Intel(R) PRO/100 family of adapters.
	  To verify that your adapter is supported, find the board ID number 
	  on the adapter. Look for a label that has a barcode and a number 
	  in the format 123456-001 (six digits hyphen three digits). 

	  Use the above information and the Adapter & Driver ID Guide at:

	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>

          to identify the adapter.

	  For the latest Intel PRO/100 network driver for Linux, see:

	  <http://appsr.intel.com/scripts-df/support_intel.asp>

	  More specific information on configuring the driver is in 
	  <file:Documentation/networking/e100.txt>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called e100.

config LNE390
	tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called lne390.

config FEALNX
	tristate "Myson MTD-8xx PCI Ethernet support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
	  cards. Specifications and data at
	  <http://www.myson.com.hk/mtd/datasheet/>.

config NATSEMI
	tristate "National Semiconductor DP8381x series PCI Ethernet support"
	depends on NET_PCI && PCI
	select CRC32
	help
	  This driver is for the National Semiconductor DP83810 series,
	  which is used in cards from PureData, NetGear, Linksys
	  and others, including the 83815 chip.
	  More specific information and updates are available from
	  <http://www.scyld.com/network/natsemi.html>.

config NE2K_PCI
	tristate "PCI NE2000 and clones support (see help)"
	depends on NET_PCI && PCI
	select CRC32
	---help---
	  This driver is for NE2000 compatible PCI cards. It will not work
	  with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
	  support" below). If you have a PCI NE2000 network (Ethernet) card,
	  say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  This driver also works for the following NE2000 clone cards:
	  RealTek RTL-8029  Winbond 89C940  Compex RL2000  KTI ET32P2
	  NetVin NV5000SC   Via 86C926      SureCom NE34   Winbond
	  Holtek HT80232    Holtek HT80229

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called ne2k-pci.

config NE3210
	tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Note that this driver
	  will NOT WORK for NE3200 cards as they are completely different.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called ne3210.

config ES3210
	tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called es3210.

config 8139CP
	tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
	depends on NET_PCI && PCI && EXPERIMENTAL
	select CRC32
	select MII
	help
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the RTL8139C+ chips. If you have one of those, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called 8139cp.  This is recommended.

config 8139TOO
	tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	---help---
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the RTL 8129/8130/8139 chips. If you have one of those, say Y and
	  read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called 8139too.  This is recommended.

config 8139TOO_PIO
	bool "Use PIO instead of MMIO"
	default y
	depends on 8139TOO
	help
	  This instructs the driver to use programmed I/O ports (PIO) instead
	  of PCI shared memory (MMIO).  This can possibly solve some problems
	  in case your mainboard has memory consistency issues.  If unsure,
	  say N.

config 8139TOO_TUNE_TWISTER
	bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
	depends on 8139TOO
	help
	  This implements a function which might come in handy in case you
	  are using low quality on long cabling. It is required for RealTek
	  RTL-8139 revision K boards, and totally unused otherwise.  It tries
	  to match the transceiver to the cable characteristics. This is
	  experimental since hardly documented by the manufacturer.
	  If unsure, say Y.

config 8139TOO_8129
	bool "Support for older RTL-8129/8130 boards"
	depends on 8139TOO
	help
	  This enables support for the older and uncommon RTL-8129 and
	  RTL-8130 chips, which support MII via an external transceiver,
	  instead of an internal one.  Disabling this option will save some
	  memory by making the code size smaller.  If unsure, say Y.

config 8139_OLD_RX_RESET
	bool "Use older RX-reset method"
	depends on 8139TOO
	help
	  The 8139too driver was recently updated to contain a more rapid
	  reset sequence, in the face of severe receive errors.  This "new"
	  RX-reset method should be adequate for all boards.  But if you
	  experience problems, you can enable this option to restore the
	  old RX-reset behavior.  If unsure, say N.

config SIS900
	tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	---help---
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
	  SiS 630 and SiS 540 chipsets.  If you have one of those, say Y and
	  read the Ethernet-HOWTO, available at
	  <http://www.tldp.org/docs.html#howto>.  Please read
	  <file:Documentation/networking/sis900.txt> and comments at the
	  beginning of <file:drivers/net/sis900.c> for more information.

	  This driver also supports AMD 79C901 HomePNA so that you can use
	  your phone line as a network cable.

	  To compile this driver as a module, choose M here: the module
	  will be called sis900.  This is recommended.

config EPIC100
	tristate "SMC EtherPower II"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
	  which is based on the SMC83c17x (EPIC/100).
	  More specific information and updates are available from
	  <http://www.scyld.com/network/epic100.html>.

config SUNDANCE
	tristate "Sundance Alta support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  This driver is for the Sundance "Alta" chip.
	  More specific information and updates are available from
	  <http://www.scyld.com/network/sundance.html>.

config SUNDANCE_MMIO
	bool "Use MMIO instead of PIO"
	depends on SUNDANCE
	help
	  Enable memory-mapped I/O for interaction with Sundance NIC registers.
	  Do NOT enable this by default, PIO (enabled when MMIO is disabled)
	  is known to solve bugs on certain chips.

	  If unsure, say N.

config TLAN
	tristate "TI ThunderLAN support"
	depends on NET_PCI && (PCI || EISA) && !64BIT
	---help---
	  If you have a PCI Ethernet network card based on the ThunderLAN chip
	  which is supported by this driver, say Y and read the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  Devices currently supported by this driver are Compaq Netelligent,
	  Compaq NetFlex and Olicom cards.  Please read the file
	  <file:Documentation/networking/tlan.txt> for more details.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called tlan.

	  Please email feedback to <torben.mathiasen@compaq.com>.

config VIA_RHINE
	tristate "VIA Rhine support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
	  Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
	  Ethernet functions can also be found integrated on South Bridges
	  (e.g. VT8235).

	  To compile this driver as a module, choose M here. The module
	  will be called via-rhine.

config VIA_RHINE_MMIO
	bool "Use MMIO instead of PIO"
	depends on VIA_RHINE
	help
	  This instructs the driver to use PCI shared memory (MMIO) instead of
	  programmed I/O ports (PIO). Enabling this gives an improvement in
	  processing time in parts of the driver.

	  If unsure, say Y.

config LAN_SAA9730
	bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
	depends on NET_PCI && EXPERIMENTAL && MIPS
	help
	  The SAA9730 is a combined multimedia and peripheral controller used
	  in thin clients, Internet access terminals, and diskless
	  workstations.
	  See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.

config NET_POCKET
	bool "Pocket and portable adapters"
	depends on NET_ETHERNET && PARPORT
	---help---
	  Cute little network (Ethernet) devices which attach to the parallel
	  port ("pocket adapters"), commonly used with laptops. If you have
	  one of those, say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  If you want to plug a network (or some other) card into the PCMCIA
	  (or PC-card) slot of your laptop instead (PCMCIA is the standard for
	  credit card size extension cards used by all modern laptops), you
	  need the pcmcia-cs package (location contained in the file
	  <file:Documentation/Changes>) and you can say N here.

	  Laptop users should read the Linux Laptop home page at
	  <http://www.linux-on-laptops.com/> or
	  Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network devices. If you say Y, you
	  will be asked for your specific device in the following questions.

config ATP
	tristate "AT-LAN-TEC/RealTek pocket adapter support"
	depends on NET_POCKET && PARPORT && X86
	select CRC32
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>, if you
	  want to use this.  If you intend to use this driver, you should have
	  said N to the "Parallel printer support", because the two drivers
	  don't like each other.

	  To compile this driver as a module, choose M here: the module
	  will be called atp.

config DE600
	tristate "D-Link DE600 pocket adapter support"
	depends on NET_POCKET && PARPORT
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:Documentation/networking/DLINK.txt> as well as the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, if you want to use
	  this. It is possible to have several devices share a single parallel
	  port and it is safe to compile the corresponding drivers into the
	  kernel.

	  To compile this driver as a module, choose M here: the module
	  will be called de600.

config DE620
	tristate "D-Link DE620 pocket adapter support"
	depends on NET_POCKET && PARPORT
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:Documentation/networking/DLINK.txt> as well as the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, if you want to use
	  this. It is possible to have several devices share a single parallel
	  port and it is safe to compile the corresponding drivers into the
	  kernel.

	  To compile this driver as a module, choose M here: the module
	  will be called de620.

config SGISEEQ
	tristate "SGI Seeq ethernet controller support"
	depends on NET_ETHERNET && SGI_IP22
	help
	  Say Y here if you have an Seeq based Ethernet network card. This is
	  used in many Silicon Graphics machines.

config DECLANCE
	tristate "DEC LANCE ethernet controller support"
	depends on NET_ETHERNET && MACH_DECSTATION
	select CRC32
	help
	  This driver is for the series of Ethernet controllers produced by
	  DEC (now Compaq) based on the AMD Lance chipset, including the
	  DEPCA series.  (This chipset is better known via the NE2100 cards.)

config 68360_ENET
	bool "Motorola 68360 ethernet controller"
	depends on M68360
	help
	  Say Y here if you want to use the built-in ethernet controller of
	  the Motorola 68360 processor.

config FEC
	bool "FEC ethernet controller (of ColdFire CPUs)"
	depends on M523x || M527x || M5272 || M528x || M520x
	help
	  Say Y here if you want to use the built-in 10/100 Fast ethernet
	  controller on some Motorola ColdFire processors.

config FEC2
	bool "Second FEC ethernet controller (on some ColdFire CPUs)"
	depends on FEC
	help
	  Say Y here if you want to use the second built-in 10/100 Fast
	  ethernet controller on some Motorola ColdFire processors.

config NE_H8300
	tristate "NE2000 compatible support for H8/300"
	depends on H8300 && NET_ETHERNET
	help
	  Say Y here if you want to use the NE2000 compatible
	  controller on the Renesas H8/300 processor.

source "drivers/net/fec_8xx/Kconfig"
source "drivers/net/fs_enet/Kconfig"

endmenu

#
#	Gigabit Ethernet
#

menu "Ethernet (1000 Mbit)"
	depends on !UML

config ACENIC
	tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
	depends on PCI
	---help---
	  Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
	  GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
	  adapter. The driver allows for using the Jumbo Frame option (9000
	  bytes/frame) however it requires that your switches can handle this
	  as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
	  line.

	  To compile this driver as a module, choose M here: the
	  module will be called acenic.

config ACENIC_OMIT_TIGON_I
	bool "Omit support for old Tigon I based AceNICs"
	depends on ACENIC
	help
	  Say Y here if you only have Tigon II based AceNICs and want to leave
	  out support for the older Tigon I based cards which are no longer
	  being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
	  version)).  This will reduce the size of the driver object by
	  app. 100KB.  If you are not sure whether your card is a Tigon I or a
	  Tigon II, say N here.

	  The safe and default value for this is N.

config DL2K
	tristate "D-Link DL2000-based Gigabit Ethernet support"
	depends on PCI
	select CRC32
	help
	  This driver supports D-Link 2000-based gigabit ethernet cards, which
	  includes
	  D-Link DGE-550T Gigabit Ethernet Adapter.
	  D-Link DL2000-based Gigabit Ethernet Adapter.

	  To compile this driver as a module, choose M here: the
	  module will be called dl2k.

config E1000
	tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
	depends on PCI
	---help---
	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
	  adapters.  For more information on how to identify your adapter, go 
	  to the Adapter & Driver ID Guide at:

	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>

	  For general information and support, go to the Intel support
	  website at:

	  <http://support.intel.com>

	  More specific information on configuring the driver is in 
	  <file:Documentation/networking/e1000.txt>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module
	  will be called e1000.

config E1000_NAPI
	bool "Use Rx Polling (NAPI)"
	depends on E1000
	help
	  NAPI is a new driver API designed to reduce CPU and interrupt load
	  when the driver is receiving lots of packets from the card. It is
	  still somewhat experimental and thus not yet enabled by default.

	  If your estimated Rx load is 10kpps or more, or if the card will be
	  deployed on potentially unfriendly networks (e.g. in a firewall),
	  then say Y here.

	  See <file:Documentation/networking/NAPI_HOWTO.txt> for more
	  information.

	  If in doubt, say N.

config E1000_DISABLE_PACKET_SPLIT
	bool "Disable Packet Split for PCI express adapters"
	depends on E1000
	help
	  Say Y here if you want to use the legacy receive path for PCI express
	  hadware.

	  If in doubt, say N.

source "drivers/net/ixp2000/Kconfig"

config MYRI_SBUS
	tristate "MyriCOM Gigabit Ethernet support"
	depends on SBUS
	help
	  This driver supports MyriCOM Sbus gigabit Ethernet cards.

	  To compile this driver as a module, choose M here: the module
	  will be called myri_sbus.  This is recommended.

config NS83820
	tristate "National Semiconduct DP83820 support"
	depends on PCI
	help
	  This is a driver for the National Semiconductor DP83820 series
	  of gigabit ethernet MACs.  Cards using this chipset include
	  the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
	  SOHO-GA2000T, SOHO-GA2500T.  The driver supports the use of
	  zero copy.

config HAMACHI
	tristate "Packet Engines Hamachi GNIC-II support"
	depends on PCI
	select MII
	help
	  If you have a Gigabit Ethernet card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called hamachi.

config YELLOWFIN
	tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
	depends on PCI && EXPERIMENTAL
	select CRC32
	---help---
	  Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
	  adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
	  used by the Beowulf Linux cluster project.  See
	  <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
	  information about this driver in particular and Beowulf in general.

	  To compile this driver as a module, choose M here: the module
	  will be called yellowfin.  This is recommended.

config R8169
	tristate "Realtek 8169 gigabit ethernet support"
	depends on PCI
	select CRC32
	---help---
	  Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.

	  To compile this driver as a module, choose M here: the module
	  will be called r8169.  This is recommended.

config R8169_NAPI
	bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
	depends on R8169 && EXPERIMENTAL
	help
	  NAPI is a new driver API designed to reduce CPU and interrupt load
	  when the driver is receiving lots of packets from the card. It is
	  still somewhat experimental and thus not yet enabled by default.

	  If your estimated Rx load is 10kpps or more, or if the card will be
	  deployed on potentially unfriendly networks (e.g. in a firewall),
	  then say Y here.

	  See <file:Documentation/networking/NAPI_HOWTO.txt> for more
	  information.

	  If in doubt, say N.

config R8169_VLAN
	bool "VLAN support"