- 10 Oct, 2007 40 commits
-
-
Ivo van Doorn authored
Signed-off-by:
Modestas Vainius <modestas@vainius.eu> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
As pointed out by Modestas Vainius the link tuner could continue working while the radio is already down. This because at the start of disable_radio the ENABLED_RADIO flag is cleared and causes the toggle_rx to skip the stop_link_tuner() call. This will add a check to the start of the link tuner which will automatically stop the link tuner when the radio is disabled. Signed-off-by:
-
Ivo van Doorn authored
Calling cancel_delayed_work_sync() unconditionally won't hurt and it will avoid race conditions when another CPU is already executing link_tuner work. Signed-off-by:
-
Ivo van Doorn authored
Loosely based on the patch by Matthijs Kooijman, this will add the dev_flags entry into debugfs which will display rt2x00dev->flags. This will allow easier debugging of flag handling. Signed-off-by:
-
Ivo van Doorn authored
The rt2x00dev->flags has become a chaos over time, this will reorganize the flags by renaming, deleting, adding and properly implement the flags. Signed-off-by:
-
Ivo van Doorn authored
Apparently rt2561s actually has PCI ID 0x0301 and rt2561 actually has PCI ID 0x0302. Where rt2561s supports Turbo. Signed-off-by:
-
Ivo van Doorn authored
By increasing the timeout for rt2x00usb_vendor_request, we should limit the number of loops required to send a signal to the device succefully. 500ms timeout is specified by the Ralink legacy drivers for rt2500usb. For rt73usb 1000ms is specified, but that includes the timeout for the firmware which is already specified in a different define. Signed-off-by:
-
Ivo van Doorn authored
Make rt61pci_beacon_update and rt73usb_beacon_update static, they are only used inside their own source file and then only for setting it as callback funtion for mac80211. Signed-off-by:
-
Ivo van Doorn authored
The call to rt2x00lib_precalculate_link_signal resets link.rx_success which is needed when calculating the average rssi for the link tuner. Change the call order so the link tuner runs first as it doesn't need the result of the precalculate. Signed-off-by:
Adam Baker <linux@baker-net.org.uk> Signed-off-by:
-
Johannes Berg authored
The typedef is not required, we can just use "enum ieee80211_key_alg" instead of "ieee80211_key_alg" Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Michael Wu <flamingice@sourmilk.net> Signed-off-by:
-
Johannes Berg authored
Drivers are currently supposed to keep track of monitor interfaces if they allow so-called "hard" monitor, and they are also supposed to keep track of multicast etc. This patch changes that, replaces the set_multicast_list() callback with a new configure_filter() callback that takes filter flags (FIF_*) instead of interface flags (IFF_*). For a driver, this means it should open the filter as much as necessary to get all frames requested by the filter flags. Accordingly, the filter flags are named "positively", e.g. FIF_ALLMULTI. Multicast filtering is a bit special in that drivers that have no multicast address filters need to allow multicast frames through when either the FIF_ALLMULTI flag is set or when the mc_count value is positive. At the same time, drivers are no longer notified about monitor interfaces at all, this means they now need to implement the start() and stop() callbacks and the new change_filter_flags() callback. Also, the start()/stop() ordering changed, start() is now called *before* any add_interface() as it really should be, and stop() after any remove_interface(). The patch also changes the behaviour of setting the bssid to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed and the filter flag FIF_BCN_PRBRESP_PROMISC introduced. This is a lot more efficient for hardware like b43 that supports it and other hardware can still set the BSSID to all-ones. Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu (rtl8187, adm8211, and p54), Larry Finger (b43legacy), and Ivo van Doorn (rt2x00). Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Stephen Hemminger authored
Since hardware header operations are part of the protocol class not the device instance, make them into a separate object and save memory. Signed-off-by:
Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Wrap the hard_header_parse function to simplify next step of header_ops conversion. Signed-off-by:
-
Vladimir Davydov authored
Fixing memory alignment problems on the blackfin architecture (maybe on the ARM also) Signed-off-by:
Vladimir Davydov <vladimir.davydov@promwad.com> Signed-off-by:
-
Vladimir Davydov authored
Reserve two bytes to align pointer to the IP header. Signed-off-by:
-
Ryan Mallon authored
The following patch fixes the tx transmit timeout problem, which is caused by the interrupts being incorrectly check and masked. The patch moves the interrupt masking code so that interrupts are enabled only when the driver is registered and only disabled when the driver is unregistered. Signed-off-by:
Ryan Mallon <ryan@bluewatersys.com> Signed-off-by:
-
Ryan Mallon authored
Corrects a minor bug with priv->dnld_sent being set incorrectly in if_cs_host_to_card. Signed-off-by:
-
Larry Finger authored
This change cleans up the radio-related messages in several ways. (1) The state of the rfkill switch is assumed to be on, rather than tested. Now, any user without such a switch will not see any messages. For devices with such a switch, a message will be logged only if the initial state is off, or if the switch is toggled. (2) The routine for testing the switch state is no longer inline. (3) The LED handling routine is simplified. (4) The "Radio turned off" message that has confused some users has been changed to "Radio initialized". This patch is patterned after a similar change to b43 by Michael Buesch. Signed-off-by: -
Larry Finger authored
This adds support for turning the radio off in software. That's useful in environments, where you don't want the RF to radiate any signals, but don't want to bring the interface down. This patch is based on a similar patch of b43 by Michael Buesch. Signed-off-by:
-
Michael Buesch authored
This adds support for turning the radio off in software. That's useful in environments, where you don't want the RF to radiate any signals, but don't want to bring the interface down. Cc: Larry Finger <larry.finger@lwfinger.net> Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
-
Michael Buesch authored
This message is useless. Only report state changes. Cc: Larry Finger <larry.finger@lwfinger.net> Signed-off-by:
-
Michael Buesch authored
Also cleanup the code a bit and remove the inline. Signed-off-by:
-
Michael Buesch authored
It's not required and the txpower adjustment must not be in atomic. Signed-off-by:
-
Andrew Morton authored
Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Ulrich Kunitz authored
Reinhard Speyerer reported at 2007-08-10 a new device. Here are the information strings. Product: Telegent TG54USB WLAN Adapter USB ID: 129b:1666 Chip ID: zd1211 chip 129b:1666 v4330 high 00-01-36 RF2959_RF pa0 ----- FCC ID: N89-UW620Z Signed-off-by:
Ulrich Kunitz <kune@deine-taler.de> Signed-off-by:
Daniel Drake <dsd@gentoo.org> Signed-off-by:
-
Larry Finger authored
Some distros ship bcm43xx with debugging printout disabled. For those BCM43xx devices with radio on/off switches, this makes it impossible to know if the radio is on or off. This patch changes a pair of debug printk's into ordinary printk's. It also changes the message that prints when the radio is initialized to the off state as the old message seems to confuse users. Signed-off-by:
-
Jesper Juhl authored
No need to initialize to NULL when variable is never used before it's assigned the return value of a kmalloc() call. Signed-off-by:
Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by:
-
Zhu Yi authored
Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Michael Buesch authored
The remaining warning in phy.c will be fixed later. Signed-off-by:
-
Jeff Garzik authored
These have been superceded by the new ->get_sset_count() hook. Signed-off-by:
Jeff Garzik <jeff@garzik.org> Signed-off-by:
-
Michael Wu authored
Signed-off-by:
-
Joe Perches authored
This is nicer than the MAC_FMT stuff. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Ivo van Doorn authored
Signed-off-by:
-
Zhu Yi authored
This patch adds the mac80211 based wireless drivers for the Intel PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi Link AGN (4965) adapters. [ Move driver into it's own directory -DaveM ] Signed-off-by:
-
Larry Finger authored
Signed-off-by:
-
Michael Buesch authored
Signed-off-by:
-
Denis Cheng authored
Signed-off-by:
Denis Cheng <crquan@gmail.com> Signed-off-by:
-
Ralf Baechle authored
It's been a useless no-op for long enough in 2.6 so I figured it's time to remove it. The number of people that could object because they're maintaining unified 2.4 and 2.6 drivers is probably rather small. [ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ] Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
John W. Linville authored
Signed-off-by: -
Andrew Morton authored
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper': drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real': drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' Signed-off-by:
-
