- 10 Aug, 2011 1 commit
-
-
Jeff Kirsher authored
Moves the drivers for Broadcom devices into drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile changes. CC: Eilon Greenstein <eilong@broadcom.com> CC: Michael Chan <mchan@broadcom.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Gary Zambrano <zambrano@broadcom.com> CC: "Maciej W. Rozycki" <macro@linux-mips.org> Signed-off-by:Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 03 Aug, 2011 2 commits
-
-
Yaniv Rosner authored
Fix MDIO access to Warpcore on new chip version of 578xx. Signed-off-by:
Yaniv Rosner <yanivr@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
When link speed is 1G and below, pause weren't sent due to missing pause setting in the UMAC. Signed-off-by:
-
- 21 Jul, 2011 2 commits
-
-
Vladislav Zolotarov authored
This patch fixes both the failure in the self-test on 578xx and a hole in a parity recovery flow that this failure has discovered: - internal 'pending' state in a VLAN_MAC object wasn't been cleared when the object state change was called with DRV_ONLY flag, which in particular happens when a parity error happens during the self-test. - bp->sp_state wasn't cleared in the similar circumstances as described above. Signed-off-by:
Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
-
Vladislav Zolotarov authored
Fix the parity errors recovery flow for 578xx: - Add a separate column for the 578xx in the parity mask registers DB. - Fix the bnx2x_process_kill_chip_reset() to handle the blocks newly introduced in the 578xx. Cover ATC and PGLUE_B blocks for 57712 and 578xx. Signed-off-by:
-
- 05 Jul, 2011 5 commits
-
-
Yaniv Rosner authored
Add autogrEEEn support on BCM84833 and 54618se, which allows to reduce power consumption. Signed-off-by:
-
Yaniv Rosner authored
When driver is unloaded, disable PMD in addition to TX laser, provided that the management firmware will be able to enable it back. Signed-off-by:
-
Yaniv Rosner authored
Add CL37 BAM support according to configuration. Signed-off-by:
-
Yaniv Rosner authored
Change 1G copper PHY BCM54616S to BCM54618SE since we only have HW with latter one of the two. Signed-off-by:
-
Yaniv Rosner authored
Set the source MAC address for PFC packets and update its status during PMF migration. Signed-off-by:
-
- 15 Jun, 2011 9 commits
-
-
Yaniv Rosner authored
Signed-off-by:
David S. Miller <davem@conan.davemloft.net>
-
Yaniv Rosner authored
Signed-off-by:
-
Yaniv Rosner authored
Signed-off-by:
-
Yaniv Rosner authored
Signed-off-by:
-
Yaniv Rosner authored
Signed-off-by:
-
Yaniv Rosner authored
Signed-off-by:
-
Vladislav Zolotarov authored
- Added support for a parity error handling for a 57712 chip. - Changed the parity recovery scheme from per-chip to per-engine. Signed-off-by:
-
Vlad Zolotarov authored
New FW/HSI (7.0): - Added support to 578xx chips - Improved HSI - much less driver's direct access to the FW internal memory needed. New implementation of the HSI handling layer in the bnx2x (bnx2x_sp.c): - Introduced chip dependent objects that have chip independent interfaces for configuration of MACs, multicast addresses, Rx mode, indirection table, fast path queues and function initialization/cleanup. - Objects functionality is based on the private function pointers, which allows not only a per-chip but also PF/VF differentiation while still preserving the same interface towards the driver. - Objects interface is not influenced by the HSI changes which do not require providing new parameters keeping the code outside the bnx2x_sp.c invariant with regard to such HSI chnages. Changes in a CNIC, bnx2fc and bnx2i modules due to the new HSI. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
- 01 Jun, 2011 3 commits
-
-
Yaniv Rosner authored
Move BCM8726 module detection code into a separate function to be called only once during initialization. Signed-off-by:
-
Yaniv Rosner authored
Fix BCM84833 register settings. Signed-off-by:
-
Yaniv Rosner authored
In case TX fault is detected on Fiber PHYs, declare the link as down until TX fault is gone. Signed-off-by:
-
- 05 May, 2011 1 commit
-
-
Dmitry Kravkov authored
Signed-off-by:
-
- 31 Mar, 2011 1 commit
-
-
Lucas De Marchi authored
Fixes generated by 'codespell' and manually reviewed. Signed-off-by:Lucas De Marchi <lucas.demarchi@profusion.mobi>
-
- 31 Jan, 2011 1 commit
-
-
Yaniv Rosner authored
Add flexible support to control various SFP+ module features either throughout MDIO registers or GPIO pins according to NVRAM configuration Signed-off-by:
-
- 18 Jan, 2011 1 commit
-
-
Yaniv Rosner authored
Fix BCM84823 LED behavior which may show on some systems Signed-off-by:
-
- 09 Jan, 2011 1 commit
-
-
Vladislav Zolotarov authored
Fixes in registers dump: - Properly calculate dump length for 57712. - Prevent HW blocks parity attentions when dumping registers in order to prevent false parity errors handling. - Update the bnx2x_dump.h file: old one had a few bugs that could cause fatal HW error as a result of a registers dump. Signed-off-by:
-
- 16 Dec, 2010 1 commit
-
-
Vladislav Zolotarov authored
Add appropriate HW DCB/PFC configuration Signed-off-by:
-
- 01 Dec, 2010 1 commit
-
-
Dmitry Kravkov authored
NIC partitioning is another flavor of multi function - having few PCI functions share the same physical port. Unlike the currently supported mode of multi-function which depends on the switch configuration and uses outer-VLAN, the NPAR mode is switch independent and uses the MAC addresses to distribute incoming packets to the different functions. This patch adds the specific HW setting of the NPAR mode and some distinctions between switch dependent (SD) and switch independent (SI) multi-function (MF) modes where the configuration is not the same. Advance driver version to 1.60.00-6 Signed-off-by:
-
- 01 Nov, 2010 1 commit
-
-
Uwe Kleine-König authored
"gadget", "through", "command", "maintain", "maintain", "controller", "address", "between", "initiali[zs]e", "instead", "function", "select", "already", "equal", "access", "management", "hierarchy", "registration", "interest", "relative", "memory", "offset", "already", Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz>
-
- 19 Oct, 2010 1 commit
-
-
Vladislav Zolotarov authored
Signed-off-by:
-
- 06 Oct, 2010 1 commit
-
-
Dmitry Kravkov authored
57712 HW supported with same set of features as for 57710/57711 Signed-off-by:
-
- 07 Sep, 2010 3 commits
-
-
Yaniv Rosner authored
Change LED scheme for dual-media Signed-off-by:
-
Yaniv Rosner authored
Add required changes in order to support dual-media boards. Signed-off-by:
-
Yaniv Rosner authored
Start building the infrastructure for dual media by adding new component of PHY which will be used all along the function. Modify function to work with this component instead of the link_params. Signed-off-by:
-
- 01 Sep, 2010 2 commits
-
-
Yaniv Rosner authored
Change BCM848xx behavior to fit IEEE such that setting 10Mb/100Mb will use force speed, and setting 1Gb/10Gb will use auto-negotiation with the specific speed advertised Signed-off-by:
-
Yaniv Rosner authored
In BCM8727 based boards, setting default 10G link speed after link was set to 1G may lead to link down issue. The problem was setting the right value, but to the wrong registers Signed-off-by:
-
- 27 Jul, 2010 1 commit
-
-
Dmitry Kravkov authored
This commit includes files movement to newly created folder using git-mv command and fixes references in cnic and bnx2x code to each other. files moved using following: #!/bin/bash mkdir drivers/net/bnx2x/ list=$(cd drivers/net/ && ls bnx2x*.[ch]) for f in $list; do git mv -f drivers/net/$f drivers/net/bnx2x/$f done Signed-off-by:
-
- 19 Apr, 2010 1 commit
-
-
Vladislav Zolotarov authored
This patch introduces the parity errors handling code for 57710 and 57711 chips. HW is configured to stop all DMA transactions to the host and sending packets to the network once parity error is detected, which is meant to prevent silent data corruption. At the same time HW generates the attention interrupt to every function of the device where parity has been detected so that driver can start the recovery flow. The recovery is actually resetting the chip and restarting the driver on all active functions of the chip where the parity error has been reported. Signed-off-by:
-
- 04 Dec, 2009 1 commit
-
-
André Goddard Rosa authored
That is "success", "unknown", "through", "performance", "[re|un]mapping" , "access", "default", "reasonable", "[con]currently", "temperature" , "channel", "[un]used", "application", "example","hierarchy", "therefore" , "[over|under]flow", "contiguous", "threshold", "enough" and others. Signed-off-by:
André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by:
-
