GitLab

AP4EVB has to reparent PLLC2 to provide a precise HDMI clock, this is only
possible, if PLLC2 hasn't been enabled yet. Since no other driver currently
uses PLLC2 we can safely remove the CLK_ENABLE_ON_INIT flag. This fixes
the "Cannot set PLLC2 parent: -16, 1 users" error message, when trying to
use HDMI on AP4EVB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Update clock framework header comment for SH-Mobile ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This allows control of the leds on the AP4EVB board by kernel events (triggers)
like mmc0/mmc1. In userland, the leds won't be available anymore over
/sys/class/gpio but via /sys/class/leds.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Two more clocks to be managed by the runtime PM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is the SH-Mobile ARM Runtime PM implementation V3.
Only clocks are managed at this point. If Runtime PM
is disabled then the clocks will be enabled before
->probe() and disabled after ->remove().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The merge of the LCDC patches chomped a trailing , from the device list,
add it back in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Support HDMI in 720p mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add definitions for DV_CLKI and HDMI clocks, extend support for PLLC2 and some
other clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This function is necessary to ensure the detection of pen-down.
This patch support both QHD / WVGA pannel.
Tested-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

EXTAL1 is clocked at 26.0MHz
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

With these defines now it is possible to use
gpio_request(GPIO_FN_LCDC1_SELECT, NULL) or ...LCDC0... respectively to
switch between the two LCDC instances.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

On AP4EVB board, it is possible to select LCD panel type
which are parallel or MIPI by SW3, SW43 dip-switch.
This patch add parallel LCD settings and
select menu to Kconfig.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Introduce SHMOBILE_TIMER_HZ for SH-Mobile.

Allow users to select HZ on their system to
minimize potential timer drift. Use 128 Hz as
default to work well with the 32768 Hz RCLK.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

NR_IRQS_LEGACY is now defined in asm/irq.h,
so drop it in mach/irqs.h.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

MMC0/SDHI1 (CN7) can be selected by dip switch.
And card voltage can be selected by jumper pin.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the irq numbers for MMCIF
to make use of evt2irq().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The FSI changes introduced IS_ERR_VALUE() checks for error conditions,
despite clk_get() handing back a pointer. Switch these over to IS_ERR()
like the rest of the code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

SH7372 can use DMA with the SCI serial driver. Add required slave IDs and slave
descriptors.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ap4evb board is equipped with two card slots: one SD-card slot and one
SD-/MMC-card slot. The latter is connected to the second SDHI interface on
sh7372 (SDHI1). Its power supply can be jumpered either to 1.8 or 3.3V, we fix
it at default 1.8V for now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds DMA support for the sh7372 sh-mobile ARM core, using the shdma
dmaengine driver, and uses DMA for the SDHI SD-card controller on this SoC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The current SH7372 setup code registers 7 SCIF ports, which is wrong.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ap4evb uses an LCD, connected to the SoC over the MIPI bus. This patch adds
platform data to configure this display and a static clock activation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Define clock objects for switching on and off clocks for LCDC0, LCDC1 and MIPI
DSI-Tx.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is V2 of clock framework tables/code for sh7377.
MSTP support is included for the following hardware blocks:
KEYSC, SCIF, IIC, IRDA, FLCTL, USB, SDHI and UIO.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is V2 of clock framework tables/code for sh7367.
MSTP support is included for the following hardware blocks:
KEYSC, SCIF, IIC, IRDA, FLCTL, VOU, SIU, USB, SDHI and UIO.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fixes for the sh7372 clock framework:
 - remove unused #include <linux/platform_device.h>
 - add sh7372 prefix to user modifiable root clocks
 - put modifiable root clock prototypes in header file
 - fix off-by-one id error on VEU MSTP clocks
 - make arrays static
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the irq numbers on sh7372/AP4EVB
to make use of evt2irq() and intcs_evt2irq().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the irq numbers on sh7377/G4EVM
to make use of evt2irq() and intcs_evt2irq().

Makes the system cope with an updated INTCS_VECT_BASE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the irq numbers on sh7367/G3EVM
to make use of evt2irq() and intcs_evt2irq().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Extend VMALLOC_END to the I/O Window at 0xe6000000.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>