Commit dfab34aa authored by Linus Torvalds's avatar Linus Torvalds
Browse files

Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device-tree updates from Olof Johansson:
 "Part 1 of device-tree updates for 3.10.  The bulk of the churn in this
  branch is due to i.MX moving from C-defined pin control over to device
  tree, which is a one-time conversion that will allow greater
  flexibility down the road.

  Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
  handful of cleanups to tegra due to the new include file functionality
  of the device tree compiler"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
  arm: mvebu: PCIe Device Tree informations for Armada XP GP
  arm: mvebu: PCIe Device Tree informations for Armada 370 DB
  arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
  arm: mvebu: PCIe Device Tree informations for Armada XP DB
  arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
  arm: mvebu: add PCIe Device Tree informations for Armada XP
  arm: mvebu: add PCIe Device Tree informations for Armada 370
  ARM: sunxi: unify osc24M_fixed and osc24M
  arm: vt8500: Add SDHC support to WM8505 DT
  ARM: dts: Add a 64 bits version of the skeleton device tree
  ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
  ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
  ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
  ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
  ARM: dts: imx6dl-wandboard: Add USB Host support
  ARM: dts: imx51 cpu node
  ARM: dts: Add missing imx27-phytec-phycore dtb target
  ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
  ARM: i.MX51: Add PATA support
  ARM: dts: Add initial support for Wandboard Dual-Lite
  ...
parents a7726350 88cf9c5e
* Clock bindings for Freescale i.MX27
Required properties:
- compatible: Should be "fsl,imx27-ccm"
- reg: Address and length of the register set
- interrupts: Should contain CCM interrupt
- #clock-cells: Should be <1>
The clock consumer should specify the desired clock by having the clock
ID in its "clocks" phandle cell. The following is a full list of i.MX27
clocks and IDs.
Clock ID
-----------------------
dummy 0
ckih 1
ckil 2
mpll 3
spll 4
mpll_main2 5
ahb 6
ipg 7
nfc_div 8
per1_div 9
per2_div 10
per3_div 11
per4_div 12
vpu_sel 13
vpu_div 14
usb_div 15
cpu_sel 16
clko_sel 17
cpu_div 18
clko_div 19
ssi1_sel 20
ssi2_sel 21
ssi1_div 22
ssi2_div 23
clko_en 24
ssi2_ipg_gate 25
ssi1_ipg_gate 26
slcdc_ipg_gate 27
sdhc3_ipg_gate 28
sdhc2_ipg_gate 29
sdhc1_ipg_gate 30
scc_ipg_gate 31
sahara_ipg_gate 32
rtc_ipg_gate 33
pwm_ipg_gate 34
owire_ipg_gate 35
lcdc_ipg_gate 36
kpp_ipg_gate 37
iim_ipg_gate 38
i2c2_ipg_gate 39
i2c1_ipg_gate 40
gpt6_ipg_gate 41
gpt5_ipg_gate 42
gpt4_ipg_gate 43
gpt3_ipg_gate 44
gpt2_ipg_gate 45
gpt1_ipg_gate 46
gpio_ipg_gate 47
fec_ipg_gate 48
emma_ipg_gate 49
dma_ipg_gate 50
cspi3_ipg_gate 51
cspi2_ipg_gate 52
cspi1_ipg_gate 53
nfc_baud_gate 54
ssi2_baud_gate 55
ssi1_baud_gate 56
vpu_baud_gate 57
per4_gate 58
per3_gate 59
per2_gate 60
per1_gate 61
usb_ahb_gate 62
slcdc_ahb_gate 63
sahara_ahb_gate 64
lcdc_ahb_gate 65
vpu_ahb_gate 66
fec_ahb_gate 67
emma_ahb_gate 68
emi_ahb_gate 69
dma_ahb_gate 70
csi_ahb_gate 71
brom_ahb_gate 72
ata_ahb_gate 73
wdog_ipg_gate 74
usb_ipg_gate 75
uart6_ipg_gate 76
uart5_ipg_gate 77
uart4_ipg_gate 78
uart3_ipg_gate 79
uart2_ipg_gate 80
uart1_ipg_gate 81
ckih_div1p5 82
fpm 83
mpll_osc_sel 84
mpll_sel 85
Examples:
clks: ccm@10027000{
compatible = "fsl,imx27-ccm";
reg = <0x10027000 0x1000>;
#clock-cells = <1>;
};
uart1: serial@1000a000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1000a000 0x1000>;
interrupts = <20>;
clocks = <&clks 81>, <&clks 61>;
clock-names = "ipg", "per";
status = "disabled";
};
......@@ -24,9 +24,9 @@ Required properties for iomux controller:
Required properties for pin configuration node:
- fsl,pins: two integers array, represents a group of pins mux and config
setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
pin working on a specific function, CONFIG is the pad setting value like
pull-up on this pin. Please refer to fsl,<soc>-pinctrl.txt for the valid
pins and functions of each SoC.
pin working on a specific function, which consists of a tuple of
<mux_reg conf_reg input_reg mux_val input_val>. CONFIG is the pad setting
value like pull-up on this pin.
Bits used for CONFIG:
NO_PAD_CTL(1 << 31): indicate this pin does not need config.
......
* Freescale IMX6 DualLite/Solo IOMUX Controller
Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
and usage.
Required properties:
- compatible: "fsl,imx6dl-iomuxc"
- fsl,pins: two integers array, represents a group of pins mux and config
setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
pin working on a specific function, CONFIG is the pad setting value like
pull-up for this pin. Please refer to imx6dl datasheet for the valid pad
config settings.
CONFIG bits definition:
PAD_CTL_HYS (1 << 16)
PAD_CTL_PUS_100K_DOWN (0 << 14)
PAD_CTL_PUS_47K_UP (1 << 14)
PAD_CTL_PUS_100K_UP (2 << 14)
PAD_CTL_PUS_22K_UP (3 << 14)
PAD_CTL_PUE (1 << 13)
PAD_CTL_PKE (1 << 12)
PAD_CTL_ODE (1 << 11)
PAD_CTL_SPEED_LOW (1 << 6)
PAD_CTL_SPEED_MED (2 << 6)
PAD_CTL_SPEED_HIGH (3 << 6)
PAD_CTL_DSE_DISABLE (0 << 3)
PAD_CTL_DSE_240ohm (1 << 3)
PAD_CTL_DSE_120ohm (2 << 3)
PAD_CTL_DSE_80ohm (3 << 3)
PAD_CTL_DSE_60ohm (4 << 3)
PAD_CTL_DSE_48ohm (5 << 3)
PAD_CTL_DSE_40ohm (6 << 3)
PAD_CTL_DSE_34ohm (7 << 3)
PAD_CTL_SRE_FAST (1 << 0)
PAD_CTL_SRE_SLOW (0 << 0)
Refer to imx6dl-pinfunc.h in device tree source folder for all available
imx6dl PIN_FUNC_ID.
* Freescale IMX6 SoloLite IOMUX Controller
Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
and usage.
Required properties:
- compatible: "fsl,imx6sl-iomuxc"
- fsl,pins: two integers array, represents a group of pins mux and config
setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
pin working on a specific function, CONFIG is the pad setting value like
pull-up for this pin. Please refer to imx6sl datasheet for the valid pad
config settings.
CONFIG bits definition:
PAD_CTL_LVE (1 << 22)
PAD_CTL_HYS (1 << 16)
PAD_CTL_PUS_100K_DOWN (0 << 14)
PAD_CTL_PUS_47K_UP (1 << 14)
PAD_CTL_PUS_100K_UP (2 << 14)
PAD_CTL_PUS_22K_UP (3 << 14)
PAD_CTL_PUE (1 << 13)
PAD_CTL_PKE (1 << 12)
PAD_CTL_ODE (1 << 11)
PAD_CTL_SPEED_LOW (1 << 6)
PAD_CTL_SPEED_MED (2 << 6)
PAD_CTL_SPEED_HIGH (3 << 6)
PAD_CTL_DSE_DISABLE (0 << 3)
PAD_CTL_DSE_240ohm (1 << 3)
PAD_CTL_DSE_120ohm (2 << 3)
PAD_CTL_DSE_80ohm (3 << 3)
PAD_CTL_DSE_60ohm (4 << 3)
PAD_CTL_DSE_48ohm (5 << 3)
PAD_CTL_DSE_40ohm (6 << 3)
PAD_CTL_DSE_34ohm (7 << 3)
PAD_CTL_SRE_FAST (1 << 0)
PAD_CTL_SRE_SLOW (0 << 0)
Refer to imx6sl-pinfunc.h in device tree source folder for all available
imx6sl PIN_FUNC_ID.
Freescale i.MX General Purpose Timer (GPT)
Required properties:
- compatible : should be "fsl,<soc>-gpt"
- reg : Specifies base physical address and size of the registers.
- interrupts : A list of 4 interrupts; one per timer channel.
- clocks : The clocks provided by the SoC to drive the timer.
Example:
gpt1: timer@10003000 {
compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
reg = <0x10003000 0x1000>;
interrupts = <26>;
clocks = <&clks 46>, <&clks 61>;
clock-names = "ipg", "per";
};
......@@ -3,6 +3,7 @@ ifeq ($(CONFIG_OF),y)
# Keep at91 dtb files sorted alphabetically for each SoC
# rm9200
dtb-$(CONFIG_ARCH_AT91) += at91rm9200ek.dtb
dtb-$(CONFIG_ARCH_AT91) += mpa1600.dtb
# sam9260
dtb-$(CONFIG_ARCH_AT91) += animeo_ip.dtb
dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb
......@@ -26,6 +27,7 @@ dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
# sam9n12
dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
# sam9x5
dtb-$(CONFIG_ARCH_AT91) += at91-ariag25.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
......@@ -87,19 +89,26 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx25-karo-tx25.dtb \
imx25-pdk.dtb \
imx27-apf27.dtb \
imx27-apf27dev.dtb \
imx27-pdk.dtb \
imx27-phytec-phycore.dtb \
imx31-bug.dtb \
imx51-apf51.dtb \
imx51-apf51dev.dtb \
imx51-babbage.dtb \
imx53-ard.dtb \
imx53-evk.dtb \
imx53-mba53.dtb \
imx53-qsb.dtb \
imx53-smd.dtb \
imx6dl-sabreauto.dtb \
imx6dl-sabresd.dtb \
imx6dl-wandboard.dtb \
imx6q-arm2.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb
imx6q-sabresd.dtb \
imx6q-sbc6x.dtb
dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
imx23-olinuxino.dtb \
imx23-stmp378x_devb.dtb \
......
......@@ -94,5 +94,22 @@
spi-max-frequency = <50000000>;
};
};
pcie-controller {
status = "okay";
/*
* The two PCIe units are accessible through
* both standard PCIe slots and mini-PCIe
* slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
};
};
};
......@@ -33,6 +33,43 @@
clock-frequency = <600000000>;
status = "okay";
};
pinctrl {
pwr_led_pin: pwr-led-pin {
marvell,pins = "mpp63";
marvell,function = "gpo";
};
stat_led_pins: stat-led-pins {
marvell,pins = "mpp64", "mpp65";
marvell,function = "gpio";
};
};
gpio_leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
green_pwr_led {
label = "mirabox:green:pwr";
gpios = <&gpio1 31 1>;
linux,default-trigger = "heartbeat";
};
blue_stat_led {
label = "mirabox:blue:stat";
gpios = <&gpio2 0 1>;
linux,default-trigger = "cpu0";
};
green_stat_led {
label = "mirabox:green:stat";
gpios = <&gpio2 1 1>;
default-state = "off";
};
};
mdio {
phy0: ethernet-phy@0 {
reg = <0>;
......@@ -70,5 +107,32 @@
usb@d0051000 {
status = "okay";
};
i2c@d0011000 {
status = "okay";
clock-frequency = <100000>;
pca9505: pca9505@25 {
compatible = "nxp,pca9505";
gpio-controller;
#gpio-cells = <2>;
reg = <0x25>;
};
};
pcie-controller {
status = "okay";
/* Internal mini-PCIe connector */
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
/* Connected on the PCB to a USB 3.0 XHCI controller */
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
};
};
};
......@@ -73,4 +73,15 @@
status = "okay";
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Software Button";
linux,code = <116>;
gpios = <&gpio0 6 1>;
};
};
};
......@@ -181,6 +181,51 @@
clocks = <&coreclk 0>;
status = "disabled";
};
devbus-bootcs@d0010400 {
compatible = "marvell,mvebu-devbus";
reg = <0xd0010400 0x8>;
#address-cells = <1>;
#size-cells = <1>;
clocks = <&coreclk 0>;
status = "disabled";
};
devbus-cs0@d0010408 {
compatible = "marvell,mvebu-devbus";
reg = <0xd0010408 0x8>;
#address-cells = <1>;
#size-cells = <1>;
clocks = <&coreclk 0>;
status = "disabled";
};
devbus-cs1@d0010410 {
compatible = "marvell,mvebu-devbus";
reg = <0xd0010410 0x8>;
#address-cells = <1>;
#size-cells = <1>;
clocks = <&coreclk 0>;
status = "disabled";
};
devbus-cs2@d0010418 {
compatible = "marvell,mvebu-devbus";
reg = <0xd0010418 0x8>;
#address-cells = <1>;
#size-cells = <1>;
clocks = <&coreclk 0>;
status = "disabled";
};
devbus-cs3@d0010420 {
compatible = "marvell,mvebu-devbus";
reg = <0xd0010420 0x8>;
#address-cells = <1>;
#size-cells = <1>;
clocks = <&coreclk 0>;
status = "disabled";
};
};
};
......@@ -159,5 +159,63 @@
clocks = <&coreclk 0>;
};
thermal@d0018300 {
compatible = "marvell,armada370-thermal";
reg = <0xd0018300 0x4
0xd0018304 0x4>;
status = "okay";
};
pcie-controller {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
#address-cells = <3>;
#size-cells = <2>;
bus-range = <0x00 0xff>;
reg = <0xd0040000 0x2000>, <0xd0080000 0x2000>;
reg-names = "pcie0.0", "pcie1.0";
ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000 /* Port 0.0 registers */
0x82000000 0 0xd0080000 0xd0080000 0 0x00002000 /* Port 1.0 registers */
0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
pcie@1,0 {
device_type = "pci";
assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
reg = <0x0800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 5>;
status = "disabled";
};
pcie@2,0 {
device_type = "pci";
assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
reg = <0x1000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 62>;
marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
clocks = <&gateclk 9>;
status = "disabled";
};
};
};
};
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment