ide: remove some obsoleted kernel params (v2)

Remove

* "hdx=serialize"
* "idex=noautotune"
* "idex=autotune"

kernel params, they have been obsoleted for ages.

"idex=serialize", "hdx=noautotune" and "hdx=autotune" are still available
so there is no funcionality loss caused by this patch.

v2:

* fix CONFIG_BLK_DEV_4DRIVES=y build broken by version 1 of the patch
  [ /me wearing brown paper bag ]
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent e76ecf86
......@@ -232,7 +232,9 @@ Summary of ide driver parameters for kernel command line
"hdx=remap63" : remap the drive: add 63 to all sector numbers
(for DM OnTrack)
"idex=noautotune" : driver will NOT attempt to tune interface speed
"hdx=autotune" : driver will attempt to tune interface speed
to the fastest PIO mode supported,
if possible for this drive only.
......@@ -267,17 +269,6 @@ Summary of ide driver parameters for kernel command line
"idex=base,ctl" : specify both base and ctl
"idex=base,ctl,irq" : specify base, ctl, and irq number
"idex=autotune" : driver will attempt to tune interface speed
to the fastest PIO mode supported,
for all drives on this interface.
Not fully supported by all chipset types,
and quite likely to cause trouble with
older/odd IDE drives.
"idex=noautotune" : driver will NOT attempt to tune interface speed
This is the default for most chipsets,
except the cmd640.
"idex=serialize" : do not overlap operations on idex. Please note
that you will have to specify this option for
......
......@@ -1578,7 +1578,7 @@ static int __init ide_setup(char *s)
*/
if (s[0] == 'h' && s[1] == 'd' && s[2] >= 'a' && s[2] <= max_drive) {
const char *hd_words[] = {
"none", "noprobe", "nowerr", "cdrom", "serialize",
"none", "noprobe", "nowerr", "cdrom", "minus5",
"autotune", "noautotune", "minus8", "swapdata", "bswap",
"noflush", "remap", "remap63", "scsi", NULL };
unit = s[2] - 'a';
......@@ -1606,9 +1606,6 @@ static int __init ide_setup(char *s)
drive->ready_stat = 0;
hwif->noprobe = 0;
goto done;
case -5: /* "serialize" */
printk(" -- USE \"ide%d=serialize\" INSTEAD", hw);
goto do_serialize;
case -6: /* "autotune" */
drive->autotune = IDE_TUNE_AUTO;
goto obsolete_option;
......@@ -1669,7 +1666,7 @@ static int __init ide_setup(char *s)
* (-8, -9, -10) are reserved to ease the hardcoding.
*/
static const char *ide_words[] = {
"noprobe", "serialize", "autotune", "noautotune",
"noprobe", "serialize", "minus3", "minus4",
"reset", "dma", "ata66", "minus8", "minus9",
"minus10", "four", "qd65xx", "ht6560b", "cmd640_vlb",
"dtc2278", "umc8672", "ali14xx", NULL };
......@@ -1740,12 +1737,17 @@ static int __init ide_setup(char *s)
hwif->chipset = mate->chipset = ide_4drives;
mate->irq = hwif->irq;
memcpy(mate->io_ports, hwif->io_ports, sizeof(hwif->io_ports));
goto do_serialize;
hwif->mate = mate;
mate->mate = hwif;
hwif->serialized = mate->serialized = 1;
goto obsolete_option;
}
#endif /* CONFIG_BLK_DEV_4DRIVES */
case -10: /* minus10 */
case -9: /* minus9 */
case -8: /* minus8 */
case -4:
case -3:
goto bad_option;
case -7: /* ata66 */
#ifdef CONFIG_BLK_DEV_IDEPCI
......@@ -1760,16 +1762,7 @@ static int __init ide_setup(char *s)
case -5: /* "reset" */
hwif->reset = 1;
goto obsolete_option;
case -4: /* "noautotune" */
hwif->drives[0].autotune = IDE_TUNE_NOAUTO;
hwif->drives[1].autotune = IDE_TUNE_NOAUTO;
goto obsolete_option;
case -3: /* "autotune" */
hwif->drives[0].autotune = IDE_TUNE_AUTO;
hwif->drives[1].autotune = IDE_TUNE_AUTO;
goto obsolete_option;
case -2: /* "serialize" */
do_serialize:
hwif->mate = &ide_hwifs[hw^1];
hwif->mate->mate = hwif;
hwif->serialized = hwif->mate->serialized = 1;
......
......@@ -16,8 +16,8 @@
* Please set local bus speed using kernel parameter idebus
* for example, "idebus=33" stands for 33Mhz VLbus
* To activate controller support, use "ide0=qd65xx"
* To enable tuning, use "ide0=autotune"
* To enable second channel tuning (qd6580 only), use "ide1=autotune"
* To enable tuning, use "hda=autotune hdb=autotune"
* To enable 2nd channel tuning (qd6580 only), use "hdc=autotune hdd=autotune"
*/
/*
......
......@@ -57,7 +57,7 @@
* There is a 25/33MHz switch in configuration
* register, but driver is written for use at any frequency which get
* (use idebus=xx to select PCI bus speed).
* Use ide0=autotune for automatical tune of the PIO modes.
* Use hda=autotune and hdb=autotune for automatical tune of the PIO modes.
* If you get strange results, do not use this and set PIO manually
* by hdparm.
*
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment