Commit b4c1e6bf authored by David Ertman's avatar David Ertman Committed by Jeff Kirsher
Browse files

e1000e: Add support for EEE in Sx states



On I217 and newer hardware, EEE is enabled in the PHY by the software
when link is up and disabled by the hardware when link is lost.

To enable EEE in Sx (When both ends of the link support, and are enabled
for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to
automatically enable EEE when link is up, since there will be no software
to complete the task.

To configure this in the PHY, the Auto Enable LPI bit in the Low Power
Idle GPIO Control register must be set.  For normal operation in S0, this
bit must be cleared.
Signed-off-by: default avatarDave Ertman <david.m.ertman@intel.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 491a04d2
......@@ -4605,14 +4605,23 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
/* Disable LPLU if both link partners support 100BaseT
* EEE and 100Full is advertised on both ends of the
* link.
* link, and enable Auto Enable LPI since there will
* be no driver to enable LPI while in Sx.
*/
if ((eee_advert & I82579_EEE_100_SUPPORTED) &&
(dev_spec->eee_lp_ability &
I82579_EEE_100_SUPPORTED) &&
(hw->phy.autoneg_advertised & ADVERTISE_100_FULL))
(hw->phy.autoneg_advertised & ADVERTISE_100_FULL)) {
phy_ctrl &= ~(E1000_PHY_CTRL_D0A_LPLU |
E1000_PHY_CTRL_NOND0A_LPLU);
/* Set Auto Enable LPI after link up */
e1e_rphy_locked(hw,
I217_LPI_GPIO_CTRL, &phy_reg);
phy_reg |= I217_LPI_GPIO_CTRL_AUTO_EN_LPI;
e1e_wphy_locked(hw,
I217_LPI_GPIO_CTRL, phy_reg);
}
}
/* For i217 Intel Rapid Start Technology support,
......@@ -4709,6 +4718,11 @@ void e1000_resume_workarounds_pchlan(struct e1000_hw *hw)
return;
}
/* Clear Auto Enable LPI after link up */
e1e_rphy_locked(hw, I217_LPI_GPIO_CTRL, &phy_reg);
phy_reg &= ~I217_LPI_GPIO_CTRL_AUTO_EN_LPI;
e1e_wphy_locked(hw, I217_LPI_GPIO_CTRL, phy_reg);
if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
/* Restore clear on SMB if no manageability engine
* is present
......
......@@ -217,6 +217,10 @@
#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK 0x3F00
#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT 8
/* Low Power Idle GPIO Control */
#define I217_LPI_GPIO_CTRL PHY_REG(772, 18)
#define I217_LPI_GPIO_CTRL_AUTO_EN_LPI 0x0800
/* PHY Low Power Idle Control */
#define I82579_LPI_CTRL PHY_REG(772, 20)
#define I82579_LPI_CTRL_100_ENABLE 0x2000
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment