diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 8203964373ce9dfbbd90e18dc7be35b3da00637a..c4b3f4fe91aee1a0bf27d611b23bb5896886400f 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -1587,6 +1587,7 @@ static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
static struct e1000_mac_operations e82571_mac_ops = {
/* .check_mng_mode: mac type dependent */
/* .check_for_link: media type dependent */
+ .id_led_init = e1000e_id_led_init,
.cleanup_led = e1000e_cleanup_led_generic,
.clear_hw_cntrs = e1000_clear_hw_cntrs_82571,
.get_bus_info = e1000e_get_bus_info_pcie,
@@ -1598,6 +1599,7 @@ static struct e1000_mac_operations e82571_mac_ops = {
.init_hw = e1000_init_hw_82571,
.setup_link = e1000_setup_link_82571,
/* .setup_physical_interface: media type dependent */
+ .setup_led = e1000e_setup_led_generic,
};
static struct e1000_phy_operations e82_phy_ops_igp = {
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index 9acfecddb273975a0f53020097bbc01b04907f83..674a47e430341a6e796e68f8883dd2a2986d946a 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -56,6 +56,7 @@
/* Wake Up Control */
#define E1000_WUC_APME 0x00000001 /* APM Enable */
#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+#define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */
/* Wake Up Filter Control */
#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
@@ -65,6 +66,13 @@
#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+/* Wake Up Status */
+#define E1000_WUS_LNKC E1000_WUFC_LNKC
+#define E1000_WUS_MAG E1000_WUFC_MAG
+#define E1000_WUS_EX E1000_WUFC_EX
+#define E1000_WUS_MC E1000_WUFC_MC
+#define E1000_WUS_BC E1000_WUFC_BC
+
/* Extended Device Control */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
@@ -77,6 +85,7 @@
#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
+#define E1000_CTRL_EXT_PHYPDEN 0x00100000
/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
@@ -140,6 +149,7 @@
#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
#define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
#define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */
@@ -153,6 +163,7 @@
#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
@@ -255,11 +266,16 @@
#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
/* LED Control */
+#define E1000_PHY_LED0_MODE_MASK 0x00000007
+#define E1000_PHY_LED0_IVRT 0x00000008
+#define E1000_PHY_LED0_MASK 0x0000001F
+
#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT 0
#define E1000_LEDCTL_LED0_IVRT 0x00000040
#define E1000_LEDCTL_LED0_BLINK 0x00000080
+#define E1000_LEDCTL_MODE_LINK_UP 0x2
#define E1000_LEDCTL_MODE_LED_ON 0xE
#define E1000_LEDCTL_MODE_LED_OFF 0xF
@@ -676,6 +692,8 @@
#define IFE_C_E_PHY_ID 0x02A80310
#define BME1000_E_PHY_ID 0x01410CB0
#define BME1000_E_PHY_ID_R2 0x01410CB1
+#define I82577_E_PHY_ID 0x01540050
+#define I82578_E_PHY_ID 0x004DD040
/* M88E1000 Specific Registers */
#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
@@ -729,6 +747,9 @@
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
+#define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020
+#define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C
+
/* BME1000 PHY Specific Control Register */
#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index b9dc612082e0635e1865b87faa5c99855fd27e9a..d6e491bc58c9f12ee5804be623bf75c62c103755 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -98,6 +98,49 @@ struct e1000_info;
#define DEFAULT_JUMBO 9234
+/* BM/HV Specific Registers */
+#define BM_PORT_CTRL_PAGE 769
+
+#define PHY_UPPER_SHIFT 21
+#define BM_PHY_REG(page, reg) \
+ (((reg) & MAX_PHY_REG_ADDRESS) |\
+ (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
+ (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
+
+/* PHY Wakeup Registers and defines */
+#define BM_RCTL PHY_REG(BM_WUC_PAGE, 0)
+#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS PHY_REG(BM_WUC_PAGE, 3)
+#define BM_RAR_L(_i) (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
+#define BM_RAR_M(_i) (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
+#define BM_RAR_H(_i) (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
+#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
+#define BM_MTA(_i) (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
+
+#define BM_RCTL_UPE 0x0001 /* Unicast Promiscuous Mode */
+#define BM_RCTL_MPE 0x0002 /* Multicast Promiscuous Mode */
+#define BM_RCTL_MO_SHIFT 3 /* Multicast Offset Shift */
+#define BM_RCTL_MO_MASK (3 << 3) /* Multicast Offset Mask */
+#define BM_RCTL_BAM 0x0020 /* Broadcast Accept Mode */
+#define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */
+#define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */
+
+#define HV_SCC_UPPER PHY_REG(778, 16) /* Single Collision Count */
+#define HV_SCC_LOWER PHY_REG(778, 17)
+#define HV_ECOL_UPPER PHY_REG(778, 18) /* Excessive Collision Count */
+#define HV_ECOL_LOWER PHY_REG(778, 19)
+#define HV_MCC_UPPER PHY_REG(778, 20) /* Multiple Collision Count */
+#define HV_MCC_LOWER PHY_REG(778, 21)
+#define HV_LATECOL_UPPER PHY_REG(778, 23) /* Late Collision Count */
+#define HV_LATECOL_LOWER PHY_REG(778, 24)
+#define HV_COLC_UPPER PHY_REG(778, 25) /* Collision Count */
+#define HV_COLC_LOWER PHY_REG(778, 26)
+#define HV_DC_UPPER PHY_REG(778, 27) /* Defer Count */
+#define HV_DC_LOWER PHY_REG(778, 28)
+#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
+#define HV_TNCRS_LOWER PHY_REG(778, 30)
+
enum e1000_boards {
board_82571,
board_82572,
@@ -108,6 +151,7 @@ enum e1000_boards {
board_ich8lan,
board_ich9lan,
board_ich10lan,
+ board_pchlan,
};
struct e1000_queue_stats {
@@ -305,6 +349,7 @@ struct e1000_adapter {
unsigned int flags2;
struct work_struct downshift_task;
struct work_struct update_phy_task;
+ struct work_struct led_blink_task;
};
struct e1000_info {
@@ -355,6 +400,7 @@ struct e1000_info {
/* CRC Stripping defines */
#define FLAG2_CRC_STRIPPING (1 << 0)
+#define FLAG2_HAS_PHY_WAKEUP (1 << 1)
#define E1000_RX_DESC_PS(R, i) \
(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
@@ -408,6 +454,7 @@ extern struct e1000_info e1000_82583_info;
extern struct e1000_info e1000_ich8_info;
extern struct e1000_info e1000_ich9_info;
extern struct e1000_info e1000_ich10_info;
+extern struct e1000_info e1000_pch_info;
extern struct e1000_info e1000_es2_info;
extern s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
@@ -429,6 +476,7 @@ extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_setup_led_generic(struct e1000_hw *hw);
extern s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
extern s32 e1000e_led_on_generic(struct e1000_hw *hw);
extern s32 e1000e_led_off_generic(struct e1000_hw *hw);
@@ -497,6 +545,15 @@ extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
extern s32 e1000e_check_downshift(struct e1000_hw *hw);
+extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow);
+extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
+extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
+extern s32 e1000_check_polarity_82577(struct e1000_hw *hw);
+extern s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
+extern s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
+extern s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
{
diff --git a/drivers/net/e1000e/es2lan.c b/drivers/net/e1000e/es2lan.c
index 6cc3bdf4acdb61ff854d9a5927bcd41f477ae50a..ae5d73689353acf48a1146392f6a1fe50bd06a13 100644
--- a/drivers/net/e1000e/es2lan.c
+++ b/drivers/net/e1000e/es2lan.c
@@ -1366,6 +1366,7 @@ static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
}
static struct e1000_mac_operations es2_mac_ops = {
+ .id_led_init = e1000e_id_led_init,
.check_mng_mode = e1000e_check_mng_mode_generic,
/* check_for_link dependent on media type */
.cleanup_led = e1000e_cleanup_led_generic,
@@ -1379,6 +1380,7 @@ static struct e1000_mac_operations es2_mac_ops = {
.init_hw = e1000_init_hw_80003es2lan,
.setup_link = e1000e_setup_link,
/* setup_physical_interface dependent on media type */
+ .setup_led = e1000e_setup_led_generic,
};
static struct e1000_phy_operations es2_phy_ops = {
diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c
index 4d25ede88369ddefe384465c91a0a7111011cdff..3d6435617527a64bb9bc03fd85475185ac5ce140 100644
--- a/drivers/net/e1000e/ethtool.c
+++ b/drivers/net/e1000e/ethtool.c
@@ -776,6 +776,7 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
u32 after;
u32 i;
u32 toggle;
+ u32 mask;
/*
* The status register is Read Only, so a write should fail.
@@ -788,17 +789,9 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
case e1000_80003es2lan:
toggle = 0x7FFFF3FF;
break;
- case e1000_82573:
- case e1000_82574:
- case e1000_82583:
- case e1000_ich8lan:
- case e1000_ich9lan:
- case e1000_ich10lan:
+ default:
toggle = 0x7FFFF033;
break;
- default:
- toggle = 0xFFFFF833;
- break;
}
before = er32(STATUS);
@@ -844,11 +837,18 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
REG_PATTERN_TEST(E1000_TXCW, 0xC000FFFF, 0x0000FFFF);
REG_PATTERN_TEST(E1000_TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
REG_PATTERN_TEST(E1000_TIDV, 0x0000FFFF, 0x0000FFFF);
+ mask = 0x8003FFFF;
+ switch (mac->type) {
+ case e1000_ich10lan:
+ case e1000_pchlan:
+ mask |= (1 << 18);
+ break;
+ default:
+ break;
+ }
for (i = 0; i < mac->rar_entry_count; i++)
REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1),
- ((mac->type == e1000_ich10lan) ?
- 0x8007FFFF : 0x8003FFFF),
- 0xFFFFFFFF);
+ mask, 0xFFFFFFFF);
for (i = 0; i < mac->mta_reg_count; i++)
REG_PATTERN_TEST_ARRAY(E1000_MTA, i, 0xFFFFFFFF, 0xFFFFFFFF);
@@ -1786,15 +1786,22 @@ static int e1000_set_wol(struct net_device *netdev,
/* bit defines for adapter->led_status */
#define E1000_LED_ON 0
-static void e1000_led_blink_callback(unsigned long data)
+static void e1000e_led_blink_task(struct work_struct *work)
{
- struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ struct e1000_adapter *adapter = container_of(work,
+ struct e1000_adapter, led_blink_task);
if (test_and_change_bit(E1000_LED_ON, &adapter->led_status))
adapter->hw.mac.ops.led_off(&adapter->hw);
else
adapter->hw.mac.ops.led_on(&adapter->hw);
+}
+
+static void e1000_led_blink_callback(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ schedule_work(&adapter->led_blink_task);
mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
}
@@ -1807,7 +1814,9 @@ static int e1000_phys_id(struct net_device *netdev, u32 data)
data = INT_MAX;
if ((hw->phy.type == e1000_phy_ife) ||
+ (hw->mac.type == e1000_pchlan) ||
(hw->mac.type == e1000_82574)) {
+ INIT_WORK(&adapter->led_blink_task, e1000e_led_blink_task);
if (!adapter->blink_timer.function) {
init_timer(&adapter->blink_timer);
adapter->blink_timer.function =
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 6cdb703be9513816f17fbcaa4096dddd70d1f35d..fce3f0529e4cd72b640d9aab7c128f8f5d43486e 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -193,7 +193,11 @@ enum e1e_registers {
E1000_RXCSUM = 0x05000, /* Rx Checksum Control - RW */
E1000_RFCTL = 0x05008, /* Receive Filter Control */
E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */
- E1000_RA = 0x05400, /* Receive Address - RW Array */
+ E1000_RAL_BASE = 0x05400, /* Receive Address Low - RW */
+#define E1000_RAL(_n) (E1000_RAL_BASE + ((_n) * 8))
+#define E1000_RA (E1000_RAL(0))
+ E1000_RAH_BASE = 0x05404, /* Receive Address High - RW */
+#define E1000_RAH(_n) (E1000_RAH_BASE + ((_n) * 8))
E1000_VFTA = 0x05600, /* VLAN Filter Table Array - RW Array */
E1000_WUC = 0x05800, /* Wakeup Control - RW */
E1000_WUFC = 0x05808, /* Wakeup Filter Control - RW */
@@ -368,6 +372,10 @@ enum e1e_registers {
#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE
#define E1000_DEV_ID_ICH10_D_BM_LM 0x10DE
#define E1000_DEV_ID_ICH10_D_BM_LF 0x10DF
+#define E1000_DEV_ID_PCH_M_HV_LM 0x10EA
+#define E1000_DEV_ID_PCH_M_HV_LC 0x10EB
+#define E1000_DEV_ID_PCH_D_HV_DM 0x10EF
+#define E1000_DEV_ID_PCH_D_HV_DC 0x10F0
#define E1000_REVISION_4 4
@@ -383,6 +391,7 @@ enum e1000_mac_type {
e1000_ich8lan,
e1000_ich9lan,
e1000_ich10lan,
+ e1000_pchlan,
};
enum e1000_media_type {
@@ -417,6 +426,8 @@ enum e1000_phy_type {
e1000_phy_igp_3,
e1000_phy_ife,
e1000_phy_bm,
+ e1000_phy_82578,
+ e1000_phy_82577,
};
enum e1000_bus_width {
@@ -720,6 +731,7 @@ struct e1000_host_mng_command_info {
/* Function pointers and static data for the MAC. */
struct e1000_mac_operations {
+ s32 (*id_led_init)(struct e1000_hw *);
bool (*check_mng_mode)(struct e1000_hw *);
s32 (*check_for_link)(struct e1000_hw *);
s32 (*cleanup_led)(struct e1000_hw *);
@@ -733,11 +745,13 @@ struct e1000_mac_operations {
s32 (*init_hw)(struct e1000_hw *);
s32 (*setup_link)(struct e1000_hw *);
s32 (*setup_physical_interface)(struct e1000_hw *);
+ s32 (*setup_led)(struct e1000_hw *);
};
/* Function pointers for the PHY. */
struct e1000_phy_operations {
s32 (*acquire_phy)(struct e1000_hw *);
+ s32 (*check_polarity)(struct e1000_hw *);
s32 (*check_reset_block)(struct e1000_hw *);
s32 (*commit_phy)(struct e1000_hw *);
s32 (*force_speed_duplex)(struct e1000_hw *);
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index b63d9878b0ac70b668f4279818d6c5bceba3361c..b69c8190da308c66a3f3a4383e241e0938aee43a 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -48,6 +48,10 @@
* 82567LF-3 Gigabit Network Connection
* 82567LM-3 Gigabit Network Connection
* 82567LM-4 Gigabit Network Connection
+ * 82577LM Gigabit Network Connection
+ * 82577LC Gigabit Network Connection
+ * 82578DM Gigabit Network Connection
+ * 82578DC Gigabit Network Connection
*/
#include <linux/netdevice.h>
@@ -116,6 +120,8 @@
#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
+#define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
+
/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
/* Offset 04h HSFSTS */
union ich8_hws_flash_status {
@@ -186,6 +192,14 @@ static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw);
static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw);
+static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw);
+static s32 e1000_led_on_ich8lan(struct e1000_hw *hw);
+static s32 e1000_led_off_ich8lan(struct e1000_hw *hw);
+static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw);
+static s32 e1000_setup_led_pchlan(struct e1000_hw *hw);
+static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
+static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
+static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
@@ -212,6 +226,41 @@ static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
#define ew16flash(reg,val) __ew16flash(hw, (reg), (val))
#define ew32flash(reg,val) __ew32flash(hw, (reg), (val))
+/**
+ * e1000_init_phy_params_pchlan - Initialize PHY function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific PHY parameters and function pointers.
+ **/
+static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+
+ phy->addr = 1;
+ phy->reset_delay_us = 100;
+
+ phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan;
+ phy->ops.read_phy_reg = e1000_read_phy_reg_hv;
+ phy->ops.write_phy_reg = e1000_write_phy_reg_hv;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ phy->id = e1000_phy_unknown;
+ e1000e_get_phy_id(hw);
+ phy->type = e1000e_get_phy_type_from_id(phy->id);
+
+ if (phy->type == e1000_phy_82577) {
+ phy->ops.check_polarity = e1000_check_polarity_82577;
+ phy->ops.force_speed_duplex =
+ e1000_phy_force_speed_duplex_82577;
+ phy->ops.get_cable_length = e1000_get_cable_length_82577;
+ phy->ops.get_phy_info = e1000_get_phy_info_82577;
+ phy->ops.commit_phy = e1000e_phy_sw_reset;
+ }
+
+ return ret_val;
+}
+
/**
* e1000_init_phy_params_ich8lan - Initialize PHY function pointers
* @hw: pointer to the HW structure
@@ -273,6 +322,8 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
break;
}
+ phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan;
+
return 0;
}
@@ -358,6 +409,36 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter)
/* Set if manageability features are enabled. */
mac->arc_subsystem_valid = 1;
+ /* LED operations */
+ switch (mac->type) {
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ /* ID LED init */
+ mac->ops.id_led_init = e1000e_id_led_init;
+ /* setup LED */
+ mac->ops.setup_led = e1000e_setup_led_generic;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000_cleanup_led_ich8lan;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000_led_on_ich8lan;
+ mac->ops.led_off = e1000_led_off_ich8lan;
+ break;
+ case e1000_pchlan:
+ /* ID LED init */
+ mac->ops.id_led_init = e1000_id_led_init_pchlan;
+ /* setup LED */
+ mac->ops.setup_led = e1000_setup_led_pchlan;
+ /* cleanup LED */
+ mac->ops.cleanup_led = e1000_cleanup_led_pchlan;
+ /* turn on/off LED */
+ mac->ops.led_on = e1000_led_on_pchlan;
+ mac->ops.led_off = e1000_led_off_pchlan;
+ break;
+ default:
+ break;
+ }
+
/* Enable PCS Lock-loss workaround for ICH8 */
if (mac->type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, 1);
@@ -378,7 +459,10 @@ static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter)
if (rc)
return rc;
- rc = e1000_init_phy_params_ich8lan(hw);
+ if (hw->mac.type == e1000_pchlan)
+ rc = e1000_init_phy_params_pchlan(hw);
+ else
+ rc = e1000_init_phy_params_ich8lan(hw);
if (rc)
return rc;
@@ -415,12 +499,15 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
while (timeout) {
extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
- extcnf_ctrl = er32(EXTCNF_CTRL);
- if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
- break;
+ if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) {
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+ break;
+ }
mdelay(1);
timeout--;
}
@@ -559,6 +646,53 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
return 0;
}
+/**
+ * e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
+ * done after every PHY reset.
+ **/
+static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ if (((hw->phy.type == e1000_phy_82577) &&
+ ((hw->phy.revision == 1) || (hw->phy.revision == 2))) ||
+ ((hw->phy.type == e1000_phy_82578) && (hw->phy.revision == 1))) {
+ /* Disable generation of early preamble */
+ ret_val = e1e_wphy(hw, PHY_REG(769, 25), 0x4431);
+ if (ret_val)
+ return ret_val;
+
+ /* Preamble tuning for SSC */
+ ret_val = e1e_wphy(hw, PHY_REG(770, 16), 0xA204);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (hw->phy.type == e1000_phy_82578) {
+ /*
+ * Return registers to default by doing a soft reset then
+ * writing 0x3140 to the control register.
+ */
+ if (hw->phy.revision < 2) {
+ e1000e_phy_sw_reset(hw);
+ ret_val = e1e_wphy(hw, PHY_CONTROL, 0x3140);
+ }
+ }
+
+ /* Select page 0 */
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+ hw->phy.addr = 1;
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
/**
* e1000_phy_hw_reset_ich8lan - Performs a PHY reset
* @hw: pointer to the HW structure
@@ -580,6 +714,12 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
/*
* Initialize the PHY from the NVM on ICH platforms. This
* is needed due to an issue where the NVM configuration is
@@ -706,7 +846,7 @@ static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw)
phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE));
if (phy->polarity_correction) {
- ret_val = e1000_check_polarity_ife_ich8lan(hw);
+ ret_val = phy->ops.check_polarity(hw);
if (ret_val)
return ret_val;
} else {
@@ -746,6 +886,8 @@ static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw)
break;
case e1000_phy_igp_3:
case e1000_phy_bm:
+ case e1000_phy_82578:
+ case e1000_phy_82577:
return e1000e_get_phy_info_igp(hw);
break;
default:
@@ -1856,6 +1998,79 @@ static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data)
return 0;
}
+/**
+ * e1000_id_led_init_pchlan - store LED configurations
+ * @hw: pointer to the HW structure
+ *
+ * PCH does not control LEDs via the LEDCTL register, rather it uses
+ * the PHY LED configuration register.
+ *
+ * PCH also does not have an "always on" or "always off" mode which
+ * complicates the ID feature. Instead of using the "on" mode to indicate
+ * in ledctl_mode2 the LEDs to use for ID (see e1000e_id_led_init()),
+ * use "link_up" mode. The LEDs will still ID on request if there is no
+ * link based on logic in e1000_led_[on|off]_pchlan().
+ **/
+static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LINK_UP;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LINK_UP | E1000_PHY_LED0_IVRT;
+ u16 data, i, temp, shift;
+
+ /* Get default ID LED modes */
+ ret_val = hw->nvm.ops.valid_led_default(hw, &data);
+ if (ret_val)
+ goto out;
+
+ mac->ledctl_default = er32(LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & E1000_LEDCTL_LED0_MODE_MASK;
+ shift = (i * 5);
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode1 |= (ledctl_on << shift);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode1 |= (ledctl_off << shift);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode2 |= (ledctl_on << shift);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
+ mac->ledctl_mode2 |= (ledctl_off << shift);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
/**
* e1000_get_bus_info_ich8lan - Get/Set the bus type and width
* @hw: pointer to the HW structure
@@ -1965,6 +2180,9 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
kab |= E1000_KABGTXD_BGSQLBIAS;
ew32(KABGTXD, kab);
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+
return ret_val;
}
@@ -1990,7 +2208,7 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
e1000_initialize_hw_bits_ich8lan(hw);
/* Initialize identification LED */
- ret_val = e1000e_id_led_init(hw);
+ ret_val = mac->ops.id_led_init(hw);
if (ret_val) {
hw_dbg(hw, "Error initializing identification LED\n");
return ret_val;
@@ -2035,6 +2253,16 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
ew32(CTRL_EXT, ctrl_ext);
+ /*
+ * The 82578 Rx buffer will stall if wakeup is enabled in host and
+ * the ME. Reading the BM_WUC register will clear the host wakeup bit.
+ * Reset the phy after disabling host wakeup to reset the Rx buffer.
+ */
+ if (hw->phy.type == e1000_phy_82578) {
+ e1e_rphy(hw, BM_WUC, &i);
+ e1000e_phy_hw_reset_generic(hw);
+ }
+
/*
* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
@@ -2059,6 +2287,9 @@ static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
/* Extended Device Control */
reg = er32(CTRL_EXT);
reg |= (1 << 22);
+ /* Enable PHY low-power state when MAC is at D3 w/o WoL */
+ if (hw->mac.type >= e1000_pchlan)
+ reg |= E1000_CTRL_EXT_PHYPDEN;
ew32(CTRL_EXT, reg);
/* Transmit Descriptor Control 0 */
@@ -2135,6 +2366,14 @@ static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw)
return ret_val;
ew32(FCTTV, hw->fc.pause_time);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ ret_val = hw->phy.ops.write_phy_reg(hw,
+ PHY_REG(BM_PORT_CTRL_PAGE, 27),
+ hw->fc.pause_time);
+ if (ret_val)
+ return ret_val;
+ }
return e1000e_set_fc_watermarks(hw);
}
@@ -2174,18 +2413,26 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- if (hw->phy.type == e1000_phy_igp_3) {
+ switch (hw->phy.type) {
+ case e1000_phy_igp_3:
ret_val = e1000e_copper_link_setup_igp(hw);
if (ret_val)
return ret_val;
- } else if (hw->phy.type == e1000_phy_bm) {
+ break;
+ case e1000_phy_bm:
+ case e1000_phy_82578:
ret_val = e1000e_copper_link_setup_m88(hw);
if (ret_val)
return ret_val;
- }
-
- if (hw->phy.type == e1000_phy_ife) {
- ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, ®_data);
+ break;
+ case e1000_phy_82577:
+ ret_val = e1000_copper_link_setup_82577(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ case e1000_phy_ife:
+ ret_val = hw->phy.ops.read_phy_reg(hw, IFE_PHY_MDIX_CONTROL,
+ ®_data);
if (ret_val)
return ret_val;
@@ -2203,9 +2450,13 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
reg_data |= IFE_PMC_AUTO_MDIX;
break;
}
- ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, reg_data);
+ ret_val = hw->phy.ops.write_phy_reg(hw, IFE_PHY_MDIX_CONTROL,
+ reg_data);
if (ret_val)
return ret_val;
+ break;
+ default:
+ break;
}
return e1000e_setup_copper_link(hw);
}
@@ -2422,18 +2673,26 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
* 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
* to a lower speed.
*
- * Should only be called for ICH9 and ICH10 devices.
+ * Should only be called for applicable parts.
**/
void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
{
u32 phy_ctrl;
- if ((hw->mac.type == e1000_ich10lan) ||
- (hw->mac.type == e1000_ich9lan)) {
+ switch (hw->mac.type) {
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ case e1000_pchlan:
phy_ctrl = er32(PHY_CTRL);
phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU |
E1000_PHY_CTRL_GBE_DISABLE;
ew32(PHY_CTRL, phy_ctrl);
+
+ /* Workaround SWFLAG unexpectedly set during S0->Sx */
+ if (hw->mac.type == e1000_pchlan)
+ udelay(500);
+ default:
+ break;
}
return;
@@ -2486,6 +2745,92 @@ static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
return 0;
}
+/**
+ * e1000_setup_led_pchlan - Configures SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * This prepares the SW controllable LED for use.
+ **/
+static s32 e1000_setup_led_pchlan(struct e1000_hw *hw)
+{
+ return hw->phy.ops.write_phy_reg(hw, HV_LED_CONFIG,
+ (u16)hw->mac.ledctl_mode1);
+}
+
+/**
+ * e1000_cleanup_led_pchlan - Restore the default LED operation
+ * @hw: pointer to the HW structure
+ *
+ * Return the LED back to the default configuration.
+ **/
+static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw)
+{
+ return hw->phy.ops.write_phy_reg(hw, HV_LED_CONFIG,
+ (u16)hw->mac.ledctl_default);
+}
+
+/**
+ * e1000_led_on_pchlan - Turn LEDs on
+ * @hw: pointer to the HW structure
+ *
+ * Turn on the LEDs.
+ **/
+static s32 e1000_led_on_pchlan(struct e1000_hw *hw)
+{
+ u16 data = (u16)hw->mac.ledctl_mode2;
+ u32 i, led;
+
+ /*
+ * If no link, then turn LED on by setting the invert bit
+ * for each LED that's mode is "link_up" in ledctl_mode2.
+ */
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ for (i = 0; i < 3; i++) {
+ led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
+ if ((led & E1000_PHY_LED0_MODE_MASK) !=
+ E1000_LEDCTL_MODE_LINK_UP)
+ continue;
+ if (led & E1000_PHY_LED0_IVRT)
+ data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
+ else
+ data |= (E1000_PHY_LED0_IVRT << (i * 5));
+ }
+ }
+
+ return hw->phy.ops.write_phy_reg(hw, HV_LED_CONFIG, data);
+}
+
+/**
+ * e1000_led_off_pchlan - Turn LEDs off
+ * @hw: pointer to the HW structure
+ *
+ * Turn off the LEDs.
+ **/
+static s32 e1000_led_off_pchlan(struct e1000_hw *hw)
+{
+ u16 data = (u16)hw->mac.ledctl_mode1;
+ u32 i, led;
+
+ /*
+ * If no link, then turn LED off by clearing the invert bit
+ * for each LED that's mode is "link_up" in ledctl_mode1.
+ */
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ for (i = 0; i < 3; i++) {
+ led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
+ if ((led & E1000_PHY_LED0_MODE_MASK) !=
+ E1000_LEDCTL_MODE_LINK_UP)
+ continue;
+ if (led & E1000_PHY_LED0_IVRT)
+ data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
+ else
+ data |= (E1000_PHY_LED0_IVRT << (i * 5));
+ }
+ }
+
+ return hw->phy.ops.write_phy_reg(hw, HV_LED_CONFIG, data);
+}
+
/**
* e1000_get_cfg_done_ich8lan - Read config done bit
* @hw: pointer to the HW structure
@@ -2493,7 +2838,7 @@ static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
* Read the management control register for the config done bit for
* completion status. NOTE: silicon which is EEPROM-less will fail trying
* to read the config done bit, so an error is *ONLY* logged and returns
- * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon
+ * 0. If we were to return with error, EEPROM-less silicon
* would not be able to be reset or change link.
**/
static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
@@ -2503,7 +2848,8 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
e1000e_get_cfg_done(hw);
/* If EEPROM is not marked present, init the IGP 3 PHY manually */
- if (hw->mac.type != e1000_ich10lan) {
+ if ((hw->mac.type != e1000_ich10lan) &&
+ (hw->mac.type != e1000_pchlan)) {
if (((er32(EECD) & E1000_EECD_PRES) == 0) &&
(hw->phy.type == e1000_phy_igp_3)) {
e1000e_phy_init_script_igp3(hw);
@@ -2529,6 +2875,7 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
{
u32 temp;
+ u16 phy_data;
e1000e_clear_hw_cntrs_base(hw);
@@ -2546,22 +2893,42 @@ static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
temp = er32(IAC);
temp = er32(ICRXOC);
+ /* Clear PHY statistics registers */
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ hw->phy.ops.read_phy_reg(hw, HV_SCC_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_SCC_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_ECOL_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_ECOL_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_MCC_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_MCC_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_LATECOL_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_LATECOL_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_COLC_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_COLC_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_DC_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_DC_LOWER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_TNCRS_UPPER, &phy_data);
+ hw->phy.ops.read_phy_reg(hw, HV_TNCRS_LOWER, &phy_data);
+ }
}
static struct e1000_mac_operations ich8_mac_ops = {
+ .id_led_init = e1000e_id_led_init,
.check_mng_mode = e1000_check_mng_mode_ich8lan,
.check_for_link = e1000e_check_for_copper_link,
- .cleanup_led = e1000_cleanup_led_ich8lan,
+ /* cleanup_led dependent on mac type */
.clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan,
.get_bus_info = e1000_get_bus_info_ich8lan,
.get_link_up_info = e1000_get_link_up_info_ich8lan,
- .led_on = e1000_led_on_ich8lan,
- .led_off = e1000_led_off_ich8lan,
+ /* led_on dependent on mac type */
+ /* led_off dependent on mac type */
.update_mc_addr_list = e1000e_update_mc_addr_list_generic,
.reset_hw = e1000_reset_hw_ich8lan,
.init_hw = e1000_init_hw_ich8lan,
.setup_link = e1000_setup_link_ich8lan,
.setup_physical_interface= e1000_setup_copper_link_ich8lan,
+ /* id_led_init dependent on mac type */
};
static struct e1000_phy_operations ich8_phy_ops = {
@@ -2644,3 +3011,21 @@ struct e1000_info e1000_ich10_info = {
.phy_ops = &ich8_phy_ops,
.nvm_ops = &ich8_nvm_ops,
};
+
+struct e1000_info e1000_pch_info = {
+ .mac = e1000_pchlan,
+ .flags = FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_FLASH
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_APME_IN_WUC,
+ .pba = 26,
+ .max_hw_frame_size = 4096,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &ich8_nvm_ops,
+};
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 18a4f5902f3b5bff2ba1eb4b9b1a7a442a7119a8..be6d9e9903741650ff5fe83ff1797d112a4c53ce 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -378,6 +378,12 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
mac->get_link_status = 0;
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = e1000_link_stall_workaround_hv(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
/*
* Check if there was DownShift, must be checked
* immediately after link-up
@@ -1405,6 +1411,38 @@ s32 e1000e_id_led_init(struct e1000_hw *hw)
return 0;
}
+/**
+ * e1000e_setup_led_generic - Configures SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * This prepares the SW controllable LED for use and saves the current state
+ * of the LED so it can be later restored.
+ **/
+s32 e1000e_setup_led_generic(struct e1000_hw *hw)
+{
+ u32 ledctl;
+
+ if (hw->mac.ops.setup_led != e1000e_setup_led_generic) {
+ return -E1000_ERR_CONFIG;
+ }
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ hw->mac.ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->phy.media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ }
+
+ return 0;
+}
+
/**
* e1000e_cleanup_led_generic - Set LED config to default operation
* @hw: pointer to the HW structure
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 4072fbb6493dc7fc2c495c6bf0fbdf220f1b82df..2cb704dd9546656af4b0f36f2dedb29023614a49 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -62,6 +62,7 @@ static const struct e1000_info *e1000_info_tbl[] = {
[board_ich8lan] = &e1000_ich8_info,
[board_ich9lan] = &e1000_ich9_info,
[board_ich10lan] = &e1000_ich10_info,
+ [board_pchlan] = &e1000_pch_info,
};
#ifdef DEBUG
@@ -2308,6 +2309,23 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
if (adapter->flags2 & FLAG2_CRC_STRIPPING)
rctl |= E1000_RCTL_SECRC;
+ /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */
+ if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) {
+ u16 phy_data;
+
+ e1e_rphy(hw, PHY_REG(770, 26), &phy_data);
+ phy_data &= 0xfff8;
+ phy_data |= (1 << 2);
+ e1e_wphy(hw, PHY_REG(770, 26), phy_data);
+
+ e1e_rphy(hw, 22, &phy_data);
+ phy_data &= 0x0fff;
+ phy_data |= (1 << 14);
+ e1e_wphy(hw, 0x10, 0x2823);
+ e1e_wphy(hw, 0x11, 0x0003);
+ e1e_wphy(hw, 22, phy_data);
+ }
+
/* Setup buffer sizes */
rctl &= ~E1000_RCTL_SZ_4096;
rctl |= E1000_RCTL_BSEX;
@@ -2789,6 +2807,8 @@ void e1000e_reset(struct e1000_adapter *adapter)
e1000_get_hw_control(adapter);
ew32(WUC, 0);
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)
+ e1e_wphy(&adapter->hw, BM_WUC, 0);
if (mac->ops.init_hw(hw))
e_err("Hardware Error\n");
@@ -3269,6 +3289,7 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
struct pci_dev *pdev = adapter->pdev;
+ u16 phy_data;
/*
* Prevent stats update while adapter is being reset, or if the pci
@@ -3288,11 +3309,34 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
adapter->stats.roc += er32(ROC);
adapter->stats.mpc += er32(MPC);
- adapter->stats.scc += er32(SCC);
- adapter->stats.ecol += er32(ECOL);
- adapter->stats.mcc += er32(MCC);
- adapter->stats.latecol += er32(LATECOL);
- adapter->stats.dc += er32(DC);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_SCC_LOWER, &phy_data);
+ adapter->stats.scc += phy_data;
+
+ e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
+ e1e_rphy(hw, HV_ECOL_LOWER, &phy_data);
+ adapter->stats.ecol += phy_data;
+
+ e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_MCC_LOWER, &phy_data);
+ adapter->stats.mcc += phy_data;
+
+ e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
+ e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data);
+ adapter->stats.latecol += phy_data;
+
+ e1e_rphy(hw, HV_DC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_DC_LOWER, &phy_data);
+ adapter->stats.dc += phy_data;
+ } else {
+ adapter->stats.scc += er32(SCC);
+ adapter->stats.ecol += er32(ECOL);
+ adapter->stats.mcc += er32(MCC);
+ adapter->stats.latecol += er32(LATECOL);
+ adapter->stats.dc += er32(DC);
+ }
adapter->stats.xonrxc += er32(XONRXC);
adapter->stats.xontxc += er32(XONTXC);
adapter->stats.xoffrxc += er32(XOFFRXC);
@@ -3310,13 +3354,28 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
hw->mac.tx_packet_delta = er32(TPT);
adapter->stats.tpt += hw->mac.tx_packet_delta;
- hw->mac.collision_delta = er32(COLC);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
+ e1e_rphy(hw, HV_COLC_LOWER, &phy_data);
+ hw->mac.collision_delta = phy_data;
+ } else {
+ hw->mac.collision_delta = er32(COLC);
+ }
adapter->stats.colc += hw->mac.collision_delta;
adapter->stats.algnerrc += er32(ALGNERRC);
adapter->stats.rxerrc += er32(RXERRC);
- if ((hw->mac.type != e1000_82574) && (hw->mac.type != e1000_82583))
- adapter->stats.tncrs += er32(TNCRS);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
+ e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data);
+ adapter->stats.tncrs += phy_data;
+ } else {
+ if ((hw->mac.type != e1000_82574) &&
+ (hw->mac.type != e1000_82583))
+ adapter->stats.tncrs += er32(TNCRS);
+ }
adapter->stats.cexterr += er32(CEXTERR);
adapter->stats.tsctc += er32(TSCTC);
adapter->stats.tsctfc += er32(TSCTFC);
@@ -4342,6 +4401,81 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
}
}
+static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 i, mac_reg;
+ u16 phy_reg;
+ int retval = 0;
+
+ /* copy MAC RARs to PHY RARs */
+ for (i = 0; i < adapter->hw.mac.rar_entry_count; i++) {
+ mac_reg = er32(RAL(i));
+ e1e_wphy(hw, BM_RAR_L(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_RAR_M(i), (u16)((mac_reg >> 16) & 0xFFFF));
+ mac_reg = er32(RAH(i));
+ e1e_wphy(hw, BM_RAR_H(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_RAR_CTRL(i), (u16)((mac_reg >> 16) & 0xFFFF));
+ }
+
+ /* copy MAC MTA to PHY MTA */
+ for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
+ mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
+ e1e_wphy(hw, BM_MTA(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_MTA(i) + 1, (u16)((mac_reg >> 16) & 0xFFFF));
+ }
+
+ /* configure PHY Rx Control register */
+ e1e_rphy(&adapter->hw, BM_RCTL, &phy_reg);
+ mac_reg = er32(RCTL);
+ if (mac_reg & E1000_RCTL_UPE)
+ phy_reg |= BM_RCTL_UPE;
+ if (mac_reg & E1000_RCTL_MPE)
+ phy_reg |= BM_RCTL_MPE;
+ phy_reg &= ~(BM_RCTL_MO_MASK);
+ if (mac_reg & E1000_RCTL_MO_3)
+ phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT)
+ << BM_RCTL_MO_SHIFT);
+ if (mac_reg & E1000_RCTL_BAM)
+ phy_reg |= BM_RCTL_BAM;
+ if (mac_reg & E1000_RCTL_PMCF)
+ phy_reg |= BM_RCTL_PMCF;
+ mac_reg = er32(CTRL);
+ if (mac_reg & E1000_CTRL_RFCE)
+ phy_reg |= BM_RCTL_RFCE;
+ e1e_wphy(&adapter->hw, BM_RCTL, phy_reg);
+
+ /* enable PHY wakeup in MAC register */
+ ew32(WUFC, wufc);
+ ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
+
+ /* configure and enable PHY wakeup in PHY registers */
+ e1e_wphy(&adapter->hw, BM_WUFC, wufc);
+ e1e_wphy(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
+
+ /* activate PHY wakeup */
+ retval = hw->phy.ops.acquire_phy(hw);
+ if (retval) {
+ e_err("Could not acquire PHY\n");
+ return retval;
+ }
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+ retval = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (retval) {
+ e_err("Could not read PHY page 769\n");
+ goto out;
+ }
+ phy_reg |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
+ retval = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (retval)
+ e_err("Could not set PHY Host Wakeup bit\n");
+out:
+ hw->phy.ops.release_phy(hw);
+
+ return retval;
+}
+
static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
{
struct net_device *netdev = pci_get_drvdata(pdev);
@@ -4384,8 +4518,9 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
#define E1000_CTRL_ADVD3WUC 0x00100000
/* phy power management enable */
#define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
- ctrl |= E1000_CTRL_ADVD3WUC |
- E1000_CTRL_EN_PHY_PWR_MGMT;
+ ctrl |= E1000_CTRL_ADVD3WUC;
+ if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP))
+ ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT;
ew32(CTRL, ctrl);
if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
@@ -4403,8 +4538,17 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
/* Allow time for pending master requests to run */
e1000e_disable_pcie_master(&adapter->hw);
- ew32(WUC, E1000_WUC_PME_EN);
- ew32(WUFC, wufc);
+ if ((adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) &&
+ !(hw->mac.ops.check_mng_mode(hw))) {
+ /* enable wakeup by the PHY */
+ retval = e1000_init_phy_wakeup(adapter, wufc);
+ if (retval)
+ return retval;
+ } else {
+ /* enable wakeup by the MAC */
+ ew32(WUFC, wufc);
+ ew32(WUC, E1000_WUC_PME_EN);
+ }
} else {
ew32(WUC, 0);
ew32(WUFC, 0);
@@ -4547,8 +4691,37 @@ static int e1000_resume(struct pci_dev *pdev)
}
e1000e_power_up_phy(adapter);
+
+ /* report the system wakeup cause from S3/S4 */
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
+ u16 phy_data;
+
+ e1e_rphy(&adapter->hw, BM_WUS, &phy_data);
+ if (phy_data) {
+ e_info("PHY Wakeup cause - %s\n",
+ phy_data & E1000_WUS_EX ? "Unicast Packet" :
+ phy_data & E1000_WUS_MC ? "Multicast Packet" :
+ phy_data & E1000_WUS_BC ? "Broadcast Packet" :
+ phy_data & E1000_WUS_MAG ? "Magic Packet" :
+ phy_data & E1000_WUS_LNKC ? "Link Status "
+ " Change" : "other");
+ }
+ e1e_wphy(&adapter->hw, BM_WUS, ~0);
+ } else {
+ u32 wus = er32(WUS);
+ if (wus) {
+ e_info("MAC Wakeup cause - %s\n",
+ wus & E1000_WUS_EX ? "Unicast Packet" :
+ wus & E1000_WUS_MC ? "Multicast Packet" :
+ wus & E1000_WUS_BC ? "Broadcast Packet" :
+ wus & E1000_WUS_MAG ? "Magic Packet" :
+ wus & E1000_WUS_LNKC ? "Link Status Change" :
+ "other");
+ }
+ ew32(WUS, ~0);
+ }
+
e1000e_reset(adapter);
- ew32(WUS, ~0);
e1000_init_manageability(adapter);
@@ -4994,6 +5167,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
/* APME bit in EEPROM is mapped to WUC.APME */
eeprom_data = er32(WUC);
eeprom_apme_mask = E1000_WUC_APME;
+ if (eeprom_data & E1000_WUC_PHY_WAKE)
+ adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP;
} else if (adapter->flags & FLAG_APME_IN_CTRL3) {
if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
(adapter->hw.bus.func == 1))
@@ -5195,6 +5370,11 @@ static struct pci_device_id e1000_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan },
+
{ } /* terminate list */
};
MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index dc4a9cba6a73dcc34f16590153cd2e8a557fd9c6..e23459cf3d0eecbc64329d40db9de98aa19c7634 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -37,6 +37,9 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw);
static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
u16 *data, bool read);
+static u32 e1000_get_phy_addr_for_hv_page(u32 page);
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
/* Cable length tables */
static const u16 e1000_m88_cable_length_table[] =
@@ -54,6 +57,55 @@ static const u16 e1000_igp_2_cable_length_table[] =
#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
ARRAY_SIZE(e1000_igp_2_cable_length_table)
+#define BM_PHY_REG_PAGE(offset) \
+ ((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+ ((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+ (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+ ~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START 768
+#define I82578_ADDR_REG 29
+#define I82577_ADDR_REG 16
+#define I82577_CFG_REG 22
+#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
+#define I82577_CTRL_REG 23
+#define I82577_CTRL_DOWNSHIFT_MASK (7 << 10)
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2 18
+#define I82577_PHY_STATUS_2 26
+#define I82577_PHY_DIAG_STATUS 31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82577_PHY_STATUS2_MDIX 0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_AUTO_MDIX 0x0400
+#define I82577_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1 16
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
+
/**
* e1000e_check_reset_block_generic - Check if PHY reset is blocked
* @hw: pointer to the HW structure
@@ -82,23 +134,48 @@ s32 e1000e_check_reset_block_generic(struct e1000_hw *hw)
s32 e1000e_get_phy_id(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
- s32 ret_val;
+ s32 ret_val = 0;
u16 phy_id;
+ u16 retry_count = 0;
- ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
- if (ret_val)
- return ret_val;
+ if (!(phy->ops.read_phy_reg))
+ goto out;
- phy->id = (u32)(phy_id << 16);
- udelay(20);
- ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
- if (ret_val)
- return ret_val;
+ while (retry_count < 2) {
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ goto out;
- phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
- phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ goto out;
- return 0;
+ phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+ if (phy->id != 0 && phy->id != PHY_REVISION_MASK)
+ goto out;
+
+ /*
+ * If the PHY ID is still unknown, we may have an 82577i
+ * without link. We will try again after setting Slow
+ * MDIC mode. No harm in trying again in this case since
+ * the PHY ID is unknown at this point anyway
+ */
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ retry_count++;
+ }
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if (retry_count)
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+ return ret_val;
}
/**
@@ -409,6 +486,43 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
return ret_val;
}
+/**
+ * e1000_copper_link_setup_82577 - Setup 82577 PHY for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = phy->ops.read_phy_reg(hw, I82577_CFG_REG, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= I82577_CFG_ASSERT_CRS_ON_TX;
+
+ /* Enable downshift */
+ phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
+
+ ret_val = phy->ops.write_phy_reg(hw, I82577_CFG_REG, phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Set number of link attempts before downshift */
+ ret_val = phy->ops.read_phy_reg(hw, I82577_CTRL_REG, &phy_data);
+ if (ret_val)
+ goto out;
+ phy_data &= ~I82577_CTRL_DOWNSHIFT_MASK;
+ ret_val = phy->ops.write_phy_reg(hw, I82577_CTRL_REG, phy_data);
+
+out:
+ return ret_val;
+}
+
/**
* e1000e_copper_link_setup_m88 - Setup m88 PHY's for copper link
* @hw: pointer to the HW structure
@@ -427,8 +541,8 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* For newer PHYs this bit is downshift enable */
- if (phy->type == e1000_phy_m88)
+ /* For BM PHY this bit is downshift enable */
+ if (phy->type != e1000_phy_bm)
phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
/*
@@ -520,10 +634,27 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
/* Commit the changes. */
ret_val = e1000e_commit_phy(hw);
- if (ret_val)
+ if (ret_val) {
hw_dbg(hw, "Error committing the PHY changes\n");
+ return ret_val;
+ }
- return ret_val;
+ if (phy->type == e1000_phy_82578) {
+ ret_val = phy->ops.read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* 82578 PHY - set the downshift count to 1x. */
+ phy_data |= I82578_EPSCR_DOWNSHIFT_ENABLE;
+ phy_data &= ~I82578_EPSCR_DOWNSHIFT_COUNTER_MASK;
+ ret_val = phy->ops.write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return 0;
}
/**
@@ -1251,6 +1382,8 @@ s32 e1000e_check_downshift(struct e1000_hw *hw)
switch (phy->type) {
case e1000_phy_m88:
case e1000_phy_gg82563:
+ case e1000_phy_82578:
+ case e1000_phy_82577:
offset = M88E1000_PHY_SPEC_STATUS;
mask = M88E1000_PSSR_DOWNSHIFT;
break;
@@ -1886,6 +2019,12 @@ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id)
case BME1000_E_PHY_ID_R2:
phy_type = e1000_phy_bm;
break;
+ case I82578_E_PHY_ID:
+ phy_type = e1000_phy_82578;
+ break;
+ case I82577_E_PHY_ID:
+ phy_type = e1000_phy_82577;
+ break;
default:
phy_type = e1000_phy_unknown;
break;
@@ -2181,11 +2320,16 @@ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
u16 *data, bool read)
{
s32 ret_val;
- u16 reg = ((u16)offset) & PHY_REG_MASK;
+ u16 reg = BM_PHY_REG_NUM(offset);
u16 phy_reg = 0;
u8 phy_acquired = 1;
+ /* Gig must be disabled for MDIO accesses to page 800 */
+ if ((hw->mac.type == e1000_pchlan) &&
+ (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
+ hw_dbg(hw, "Attempting to access page 800 while gig enabled\n");
+
ret_val = hw->phy.ops.acquire_phy(hw);
if (ret_val) {
phy_acquired = 0;
@@ -2289,3 +2433,524 @@ static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
return 0;
}
+
+s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow)
+{
+ s32 ret_val = 0;
+ u16 data = 0;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Set MDIO mode - page 769, register 16: 0x2580==slow, 0x2180==fast */
+ hw->phy.addr = 1;
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+ }
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_CS_CTRL1,
+ (0x2180 | (slow << 10)));
+
+ /* dummy read when reverting to fast mode - throw away result */
+ if (!slow)
+ e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphore before exiting.
+ **/
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ if ((hw->phy.type != e1000_phy_82578) ||
+ ((reg != I82578_ADDR_REG) &&
+ (reg != I82578_ADDR_REG + 1))) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ hw->phy.addr = phy_addr;
+ }
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+ hw->phy.ops.release_phy(hw);
+
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ /*
+ * Workaround MDIO accesses being disabled after entering IEEE Power
+ * Down (whenever bit 11 of the PHY Control register is set)
+ */
+ if ((hw->phy.type == e1000_phy_82578) &&
+ (hw->phy.revision >= 1) &&
+ (hw->phy.addr == 2) &&
+ ((MAX_PHY_REG_ADDRESS & reg) == 0) &&
+ (data & (1 << 11))) {
+ u16 data2 = 0x7EFF;
+ hw->phy.ops.release_phy(hw);
+ ret_val = e1000_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
+ &data2, false);
+ if (ret_val)
+ goto out;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ if ((hw->phy.type != e1000_phy_82578) ||
+ ((reg != I82578_ADDR_REG) &&
+ (reg != I82578_ADDR_REG + 1))) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ hw->phy.addr = phy_addr;
+ }
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+ hw->phy.ops.release_phy(hw);
+
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_phy_addr_for_hv_page - Get PHY adrress based on page
+ * @page: page to be accessed
+ **/
+static u32 e1000_get_phy_addr_for_hv_page(u32 page)
+{
+ u32 phy_addr = 2;
+
+ if (page >= HV_INTC_FC_PAGE_START)
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000_access_phy_debug_regs_hv - Read HV PHY vendor specific high registers
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to be read or written
+ * @read: determines if operation is read or written
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retreived information in data. Release any acquired
+ * semaphores before exiting. Note that the procedure to read these regs
+ * uses the address port and data port to read/write.
+ **/
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u32 addr_reg = 0;
+ u32 data_reg = 0;
+ u8 phy_acquired = 1;
+
+ /* This takes care of the difference with desktop vs mobile phy */
+ addr_reg = (hw->phy.type == e1000_phy_82578) ?
+ I82578_ADDR_REG : I82577_ADDR_REG;
+ data_reg = addr_reg + 1;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Could not acquire PHY\n");
+ phy_acquired = 0;
+ goto out;
+ }
+
+ /* All operations in this function are phy address 2 */
+ hw->phy.addr = 2;
+
+ /* masking with 0x3F to remove the page from offset */
+ ret_val = e1000e_write_phy_reg_mdic(hw, addr_reg, (u16)offset & 0x3F);
+ if (ret_val) {
+ hw_dbg(hw, "Could not write PHY the HV address register\n");
+ goto out;
+ }
+
+ /* Read or write the data value next */
+ if (read)
+ ret_val = e1000e_read_phy_reg_mdic(hw, data_reg, data);
+ else
+ ret_val = e1000e_write_phy_reg_mdic(hw, data_reg, *data);
+
+ if (ret_val) {
+ hw_dbg(hw, "Could not read data value from HV data register\n");
+ goto out;
+ }
+
+out:
+ if (phy_acquired == 1)
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_link_stall_workaround_hv - Si workaround
+ * @hw: pointer to the HW structure
+ *
+ * This function works around a Si bug where the link partner can get
+ * a link up indication before the PHY does. If small packets are sent
+ * by the link partner they can be placed in the packet buffer without
+ * being properly accounted for by the PHY and will stall preventing
+ * further packets from being received. The workaround is to clear the
+ * packet buffer after the PHY detects link up.
+ **/
+s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 data;
+
+ if (hw->phy.type != e1000_phy_82578)
+ goto out;
+
+ /* check if link is up and at 1Gbps */
+ ret_val = hw->phy.ops.read_phy_reg(hw, BM_CS_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ data &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (data != (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ goto out;
+
+ mdelay(200);
+
+ /* flush the packets in the fifo buffer */
+ ret_val = hw->phy.ops.write_phy_reg(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC |
+ HV_MUX_DATA_CTRL_FORCE_SPEED);
+ if (ret_val)
+ goto out;
+
+ ret_val = hw->phy.ops.write_phy_reg(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_check_polarity_82577 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 e1000_check_polarity_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_STATUS_2, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & I82577_PHY_STATUS2_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_force_speed_duplex_82577 - Force speed/duplex for I82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ ret_val = phy->ops.read_phy_reg(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = phy->ops.write_phy_reg(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. 82577 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~I82577_PHY_CTRL2_AUTO_MDIX;
+ phy_data &= ~I82577_PHY_CTRL2_FORCE_MDI_MDIX;
+
+ ret_val = phy->ops.write_phy_reg(hw, I82577_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ goto out;
+
+ hw_dbg(hw, "I82577_PHY_CTRL_2: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg(hw, "Waiting for forced speed/duplex link on 82577 phy\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ hw_dbg(hw, "Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_get_phy_info_82577 - Retrieve I82577 PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ hw_dbg(hw, "Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = e1000_check_polarity_82577(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_STATUS_2, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & I82577_PHY_STATUS2_MDIX) ? true : false;
+
+ if ((data & I82577_PHY_STATUS2_SPEED_MASK) ==
+ I82577_PHY_STATUS2_SPEED_1000MBPS) {
+ ret_val = hw->phy.ops.get_cable_length(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_phy_reg(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_get_cable_length_82577 - Determine cable length for 82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, length;
+
+ ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_DIAG_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ length = (phy_data & I82577_DSTATUS_CABLE_LENGTH) >>
+ I82577_DSTATUS_CABLE_LENGTH_SHIFT;
+
+ if (length == E1000_CABLE_LENGTH_UNDEFINED)
+ ret_val = E1000_ERR_PHY;
+
+ phy->cable_length = length;
+
+out:
+ return ret_val;
+}