Commit 9f06d15f authored by Adrian Thomasset's avatar Adrian Thomasset Committed by Greg Kroah-Hartman
Browse files

USB: ftdi_sio: correct ST Micro Connect Lite PIDs



The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.

For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: default avatarAdrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 0b9b6df9
...@@ -869,7 +869,9 @@ static struct usb_device_id id_table_combined [] = { ...@@ -869,7 +869,9 @@ static struct usb_device_id id_table_combined [] = {
{ USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) },
{ USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID), { USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(ST_VID, ST_STMCLT1030_PID), { USB_DEVICE(ST_VID, ST_STMCLT_2232_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(ST_VID, ST_STMCLT_4232_PID),
.driver_info = (kernel_ulong_t)&ftdi_stmclite_quirk }, .driver_info = (kernel_ulong_t)&ftdi_stmclite_quirk },
{ USB_DEVICE(FTDI_VID, FTDI_RF_R106) }, { USB_DEVICE(FTDI_VID, FTDI_RF_R106) },
{ USB_DEVICE(FTDI_VID, FTDI_DISTORTEC_JTAG_LOCK_PICK_PID), { USB_DEVICE(FTDI_VID, FTDI_DISTORTEC_JTAG_LOCK_PICK_PID),
......
...@@ -1151,7 +1151,8 @@ ...@@ -1151,7 +1151,8 @@
* STMicroelectonics * STMicroelectonics
*/ */
#define ST_VID 0x0483 #define ST_VID 0x0483
#define ST_STMCLT1030_PID 0x3747 /* ST Micro Connect Lite STMCLT1030 */ #define ST_STMCLT_2232_PID 0x3746
#define ST_STMCLT_4232_PID 0x3747
/* /*
* Papouch products (http://www.papouch.com/) * Papouch products (http://www.papouch.com/)
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment