Commit 9bc64b89 authored by Vaibhav Hiremath's avatar Vaibhav Hiremath Committed by Tony Lindgren
Browse files

OMAP3EVM: Reset the smsc911x ethernet controller in board_init

With addition of hwmod support to gpio, the ethernet controller
goes undetected for OMAP35xEVM. So explicitly assert the reset signal to
ethernet controller smsc911x -

	- GPIO7 (>=RevG version of EVM's)
	- GPIO64 (<=RevD version of EVM's)

Tested this patch on RevG version of EVM with ES3.1 Si.

This patch is based on intial version from Charulatha V, reference
to original discussion -
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg35784.html

Signed-off-by: default avatarVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 741927f7
......@@ -60,6 +60,13 @@
#define OMAP3EVM_ETHR_ID_REV 0x50
#define OMAP3EVM_ETHR_GPIO_IRQ 176
#define OMAP3EVM_SMSC911X_CS 5
/*
* Eth Reset signal
* 64 = Generation 1 (<=RevD)
* 7 = Generation 2 (>=RevE)
*/
#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64
#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7
static u8 omap3_evm_version;
......@@ -126,10 +133,15 @@ static struct platform_device omap3evm_smsc911x_device = {
static inline void __init omap3evm_init_smsc911x(void)
{
int eth_cs;
int eth_cs, eth_rst;
struct clk *l3ck;
unsigned int rate;
if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST;
else
eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST;
eth_cs = OMAP3EVM_SMSC911X_CS;
l3ck = clk_get(NULL, "l3_ck");
......@@ -138,6 +150,27 @@ static inline void __init omap3evm_init_smsc911x(void)
else
rate = clk_get_rate(l3ck);
/* Configure ethernet controller reset gpio */
if (cpu_is_omap3430()) {
if (gpio_request(eth_rst, "SMSC911x gpio") < 0) {
pr_err(KERN_ERR "Failed to request %d for smsc911x\n",
eth_rst);
return;
}
if (gpio_direction_output(eth_rst, 1) < 0) {
pr_err(KERN_ERR "Failed to set direction of %d for" \
" smsc911x\n", eth_rst);
return;
}
/* reset pulse to ethernet controller*/
usleep_range(150, 220);
gpio_set_value(eth_rst, 0);
usleep_range(150, 220);
gpio_set_value(eth_rst, 1);
usleep_range(1, 2);
}
if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
OMAP3EVM_ETHR_GPIO_IRQ);
......@@ -713,6 +746,10 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP_PIN_OFF_WAKEUPENABLE),
OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW),
OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_NONE),
OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_NONE),
#ifdef CONFIG_WL12XX_PLATFORM_DATA
/* WLAN IRQ - GPIO 149 */
OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment