Commit 8f2f360d authored by Ralf Baechle's avatar Ralf Baechle
Browse files

[MIPS] IP27: Nuke leftovers of _STANDALONE


Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent edc123d1
......@@ -248,14 +248,6 @@
* for _x.
*/
#ifdef _STANDALONE
/* DO NOT USE THESE DIRECTLY IN THE KERNEL. SEE BELOW. */
#define LOCAL_HUB(_x) (HUBREG_CAST (IALIAS_BASE + (_x)))
#define REMOTE_HUB(_n, _x) (HUBREG_CAST (NODE_SWIN_BASE(_n, 1) + \
0x800000 + (_x)))
#endif /* _STANDALONE */
/*
* WARNING:
* When certain Hub chip workaround are defined, it's not sufficient
......@@ -322,20 +314,6 @@
PHYS_TO_K0(NODE_OFFSET(nasid) | ARCS_SPB_OFFSET)
#define ARCS_SPB_SIZE 0x0400
#ifdef _STANDALONE
#define ARCS_TVECTOR_OFFSET 0x2800
#define ARCS_PVECTOR_OFFSET 0x2c00
/*
* These addresses are used by the master CPU to install the transfer
* and private vectors. All others use the SPB to find them.
*/
#define TVADDR (NODE_CAC_BASE(get_nasid()) + ARCS_TVECTOR_OFFSET)
#define PVADDR (NODE_CAC_BASE(get_nasid()) + ARCS_PVECTOR_OFFSET)
#endif /* _STANDALONE */
#define KLDIR_OFFSET 0x2000
#define KLDIR_ADDR(nasid) \
TO_NODE_UNCAC((nasid), KLDIR_OFFSET)
......
......@@ -85,15 +85,15 @@
#define NASID_GET(_pa) (int) ((UINT64_CAST (_pa) >> \
NASID_SHFT) & NASID_BITMASK)
#if !defined(__ASSEMBLY__) && !defined(_STANDALONE)
#if !defined(__ASSEMBLY__)
#define NODE_SWIN_BASE(nasid, widget) \
((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN) \
: RAW_NODE_SWIN_BASE(nasid, widget))
#else /* __ASSEMBLY__ || _STANDALONE */
#else /* __ASSEMBLY__ */
#define NODE_SWIN_BASE(nasid, widget) \
(NODE_IO_BASE(nasid) + (UINT64_CAST (widget) << SWIN_SIZE_BITS))
#endif /* __ASSEMBLY__ || _STANDALONE */
#endif /* __ASSEMBLY__ */
/*
* The following definitions pertain to the IO special address
......@@ -276,76 +276,6 @@
#define _ARCSPROM
#ifdef _STANDALONE
/*
* The PROM needs to pass the device base address and the
* device pci cfg space address to the device drivers during
* install. The COMPONENT->Key field is used for this purpose.
* Macros needed by SN0 device drivers to convert the
* COMPONENT->Key field to the respective base address.
* Key field looks as follows:
*
* +----------------------------------------------------+
* |devnasid | widget |pciid |hubwidid|hstnasid | adap |
* | 2 | 1 | 1 | 1 | 2 | 1 |
* +----------------------------------------------------+
* | | | | | | |
* 64 48 40 32 24 8 0
*
* These are used by standalone drivers till the io infrastructure
* is in place.
*/
#ifndef __ASSEMBLY__
#define uchar unsigned char
#define KEY_DEVNASID_SHFT 48
#define KEY_WIDID_SHFT 40
#define KEY_PCIID_SHFT 32
#define KEY_HUBWID_SHFT 24
#define KEY_HSTNASID_SHFT 8
#define MK_SN0_KEY(nasid, widid, pciid) \
((((__psunsigned_t)nasid)<< KEY_DEVNASID_SHFT |\
((__psunsigned_t)widid) << KEY_WIDID_SHFT) |\
((__psunsigned_t)pciid) << KEY_PCIID_SHFT)
#define ADD_HUBWID_KEY(key,hubwid)\
(key|=((__psunsigned_t)hubwid << KEY_HUBWID_SHFT))
#define ADD_HSTNASID_KEY(key,hstnasid)\
(key|=((__psunsigned_t)hstnasid << KEY_HSTNASID_SHFT))
#define GET_DEVNASID_FROM_KEY(key) ((short)(key >> KEY_DEVNASID_SHFT))
#define GET_WIDID_FROM_KEY(key) ((uchar)(key >> KEY_WIDID_SHFT))
#define GET_PCIID_FROM_KEY(key) ((uchar)(key >> KEY_PCIID_SHFT))
#define GET_HUBWID_FROM_KEY(key) ((uchar)(key >> KEY_HUBWID_SHFT))
#define GET_HSTNASID_FROM_KEY(key) ((short)(key >> KEY_HSTNASID_SHFT))
#define PCI_64_TARGID_SHFT 60
#define GET_PCIBASE_FROM_KEY(key) (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
GET_WIDID_FROM_KEY(key))\
| BRIDGE_DEVIO(GET_PCIID_FROM_KEY(key)))
#define GET_PCICFGBASE_FROM_KEY(key) \
(NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
GET_WIDID_FROM_KEY(key))\
| BRIDGE_TYPE0_CFG_DEV(GET_PCIID_FROM_KEY(key)))
#define GET_WIDBASE_FROM_KEY(key) \
(NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
GET_WIDID_FROM_KEY(key)))
#define PUT_INSTALL_STATUS(c,s) c->Revision = s
#define GET_INSTALL_STATUS(c) c->Revision
#endif /* !__ASSEMBLY__ */
#endif /* _STANDALONE */
#if defined (HUB_ERR_STS_WAR)
#define ERR_STS_WAR_REGISTER IIO_IIBUSERR
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment