Commit 825a84d1 authored by Stephen Hemminger's avatar Stephen Hemminger Committed by David S. Miller
Browse files

atlx: convert to net_device_ops



Convert this driver to network device ops. Compile tested only.
Signed-off-by: default avatarStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 1e058ab5
......@@ -2880,6 +2880,21 @@ static void atl1_poll_controller(struct net_device *netdev)
}
#endif
static const struct net_device_ops atl1_netdev_ops = {
.ndo_open = atl1_open,
.ndo_stop = atl1_close,
.ndo_set_multicast_list = atlx_set_multi,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_mac_address = atl1_set_mac,
.ndo_change_mtu = atl1_change_mtu,
.ndo_do_ioctl = atlx_ioctl,
.ndo_tx_timeout = atlx_tx_timeout,
.ndo_vlan_rx_register = atlx_vlan_rx_register,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = atl1_poll_controller,
#endif
};
/*
* atl1_probe - Device Initialization Routine
* @pdev: PCI device information struct
......@@ -2967,20 +2982,9 @@ static int __devinit atl1_probe(struct pci_dev *pdev,
adapter->mii.phy_id_mask = 0x1f;
adapter->mii.reg_num_mask = 0x1f;
netdev->open = &atl1_open;
netdev->stop = &atl1_close;
netdev->netdev_ops = &atl1_netdev_ops;
netdev->hard_start_xmit = &atl1_xmit_frame;
netdev->set_multicast_list = &atlx_set_multi;
netdev->set_mac_address = &atl1_set_mac;
netdev->change_mtu = &atl1_change_mtu;
netdev->do_ioctl = &atlx_ioctl;
netdev->tx_timeout = &atlx_tx_timeout;
netdev->watchdog_timeo = 5 * HZ;
#ifdef CONFIG_NET_POLL_CONTROLLER
netdev->poll_controller = atl1_poll_controller;
#endif
netdev->vlan_rx_register = atlx_vlan_rx_register;
netdev->ethtool_ops = &atl1_ethtool_ops;
adapter->bd_number = cards_found;
......
......@@ -1311,6 +1311,22 @@ static void atl2_poll_controller(struct net_device *netdev)
}
#endif
static const struct net_device_ops atl2_netdev_ops = {
.ndo_open = atl2_open,
.ndo_stop = atl2_close,
.ndo_set_multicast_list = atl2_set_multi,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_mac_address = atl2_set_mac,
.ndo_change_mtu = atl2_change_mtu,
.ndo_do_ioctl = atl2_ioctl,
.ndo_tx_timeout = atl2_tx_timeout,
.ndo_vlan_rx_register = atl2_vlan_rx_register,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = atl2_poll_controller,
#endif
};
/*
* atl2_probe - Device Initialization Routine
* @pdev: PCI device information struct
......@@ -1384,25 +1400,10 @@ static int __devinit atl2_probe(struct pci_dev *pdev,
atl2_setup_pcicmd(pdev);
netdev->open = &atl2_open;
netdev->stop = &atl2_close;
netdev->hard_start_xmit = &atl2_xmit_frame;
netdev->set_multicast_list = &atl2_set_multi;
netdev->set_mac_address = &atl2_set_mac;
netdev->change_mtu = &atl2_change_mtu;
netdev->do_ioctl = &atl2_ioctl;
netdev->netdev_ops = &atl2_netdev_ops;
atl2_set_ethtool_ops(netdev);
#ifdef CONFIG_NET_POLL_CONTROLLER
netdev->poll_controller = atl2_poll_controller;
#endif
#ifdef HAVE_TX_TIMEOUT
netdev->tx_timeout = &atl2_tx_timeout;
netdev->watchdog_timeo = 5 * HZ;
#endif
#ifdef NETIF_F_HW_VLAN_TX
netdev->vlan_rx_register = atl2_vlan_rx_register;
#endif
strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
netdev->mem_start = mmio_start;
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment