Commit 785e3268 authored by Manuel Lauss's avatar Manuel Lauss Committed by Ralf Baechle
Browse files

MIPS: Alchemy: update core interrupt code.



This patch attempts to modernize core Alchemy interrupt handling code.

- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
  contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
  the remaining (gpio-based) interrupt sources; update all boards
  accordingly.

Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: default avatarManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
parent 7179380e
......@@ -134,3 +134,4 @@ config SOC_AU1X00
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_APM_EMULATION
select GENERIC_HARDIRQS_NO__DO_IRQ
......@@ -6,7 +6,7 @@
#
obj-y += prom.o irq.o puts.o time.o reset.o \
au1xxx_irqmap.o clocks.o platform.o power.o setup.o \
clocks.o platform.o power.o setup.o \
sleeper.o cputable.o dma.o dbdma.o gpio.o
obj-$(CONFIG_PCI) += pci.o
......
/*
* BRIEF MODULE DESCRIPTION
* Au1xxx processor specific IRQ tables
*
* Copyright 2004 Embedded Edge, LLC
* dan@embeddededge.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <au1000.h>
/* The IC0 interrupt table. This is processor, rather than
* board dependent, so no reason to keep this info in the board
* dependent files.
*
* Careful if you change match 2 request!
* The interrupt handler is called directly from the low level dispatch code.
*/
struct au1xxx_irqmap __initdata au1xxx_ic0_map[] = {
#if defined(CONFIG_SOC_AU1000)
{ AU1000_UART0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_UART1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_UART2_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_UART3_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_SSI0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_SSI1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+1, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+2, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+3, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+4, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+5, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+6, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+7, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_IRDA_TX_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_IRDA_RX_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_USB_HOST_INT, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_ACSYNC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_MAC0_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_MAC1_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_AC97C_INT, INTC_INT_RISE_EDGE, 0 },
#elif defined(CONFIG_SOC_AU1500)
{ AU1500_UART0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_PCI_INTA, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_PCI_INTB, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_UART3_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_PCI_INTC, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_PCI_INTD, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_DMA_INT_BASE, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+1, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+2, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+3, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+4, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+5, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+6, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+7, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_USB_HOST_INT, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_ACSYNC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1500_MAC0_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1500_MAC1_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_AC97C_INT, INTC_INT_RISE_EDGE, 0 },
#elif defined(CONFIG_SOC_AU1100)
{ AU1100_UART0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1100_UART1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1100_SD_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1100_UART3_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_SSI0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_SSI1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+1, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+2, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+3, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+4, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+5, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+6, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_DMA_INT_BASE+7, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_IRDA_TX_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_IRDA_RX_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_USB_HOST_INT, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_ACSYNC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1100_MAC0_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
/* { AU1000_GPIO215_208_INT, INTC_INT_HIGH_LEVEL, 0 }, */
{ AU1100_LCD_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_AC97C_INT, INTC_INT_RISE_EDGE, 0 },
#elif defined(CONFIG_SOC_AU1550)
{ AU1550_UART0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PCI_INTA, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_PCI_INTB, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_DDMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_CRYPTO_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PCI_INTC, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_PCI_INTD, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_PCI_RST_INT, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_UART1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_UART3_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PSC0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PSC1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PSC2_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_PSC3_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1550_NAND_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1550_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1550_USB_HOST_INT, INTC_INT_LOW_LEVEL, 0 },
{ AU1550_MAC0_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1550_MAC1_DMA_INT, INTC_INT_HIGH_LEVEL, 0 },
#elif defined(CONFIG_SOC_AU1200)
{ AU1200_UART0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_SWT_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1200_SD_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_DDMA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_MAE_BE_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_UART1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_MAE_FE_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_PSC0_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_PSC1_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_AES_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_CAMERA_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1200_NAND_INT, INTC_INT_RISE_EDGE, 0 },
{ AU1200_USB_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_LCD_INT, INTC_INT_HIGH_LEVEL, 0 },
{ AU1200_MAE_BOTH_INT, INTC_INT_HIGH_LEVEL, 0 },
#else
#error "Error: Unknown Alchemy SOC"
#endif
};
int __initdata au1xxx_ic0_nr_irqs = ARRAY_SIZE(au1xxx_ic0_map);
This diff is collapsed.
......@@ -51,7 +51,6 @@ static void au1000_calibrate_delay(void);
extern unsigned long save_local_and_disable(int controller);
extern void restore_local_and_enable(int controller, unsigned long mask);
extern void local_enable_irq(unsigned int irq_nr);
static DEFINE_SPINLOCK(pm_lock);
......@@ -364,7 +363,10 @@ static int pm_do_freq(ctl_table *ctl, int write, struct file *file,
*/
intc0_mask = save_local_and_disable(0);
intc1_mask = save_local_and_disable(1);
local_enable_irq(AU1000_TOY_MATCH2_INT);
val = 1 << (AU1000_TOY_MATCH2_INT - AU1000_INTC0_INT_BASE);
au_writel(val, IC0_MASKSET); /* unmask */
au_writel(val, IC0_WAKESET); /* enable wake-from-sleep */
au_sync();
spin_unlock_irqrestore(&pm_lock, flags);
au1000_calibrate_delay();
restore_local_and_enable(0, intc0_mask);
......
......@@ -27,6 +27,7 @@
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
......@@ -66,21 +67,24 @@ struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
#ifndef CONFIG_MIPS_MIRAGE
#ifdef CONFIG_MIPS_DB1550
{ AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
{ AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
#else
{ AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 Fully_Interted# */
{ AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 STSCHG# */
{ AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 Fully_Interted# */
{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 STSCHG# */
{ AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
{ AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 Fully_Interted# */
{ AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 STSCHG# */
{ AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 Fully_Interted# */
{ AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 STSCHG# */
{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
#endif
#else
{ AU1000_GPIO_7, INTC_INT_RISE_EDGE, 0 }, /* touchscreen pen down */
{ AU1000_GPIO_7, IRQF_TRIGGER_RISING, 0 }, /* touchscreen pen down */
#endif
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
......@@ -32,11 +32,9 @@
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_15, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
const char *get_system_type(void)
{
......@@ -47,6 +45,11 @@ void board_reset(void)
{
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
u32 pin_func, static_cfg0;
......
......@@ -25,6 +25,7 @@
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1100.h>
......@@ -33,14 +34,12 @@
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
{ AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
{ AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
{ AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
{ AU1000_GPIO_9, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card Fully_Inserted# */
{ AU1000_GPIO_10, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card STSCHG# */
{ AU1000_GPIO_11, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card IRQ# */
{ AU1000_GPIO_13, IRQF_TRIGGER_LOW, 0 }, /* DC_IRQ# */
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
const char *get_system_type(void)
{
......@@ -53,6 +52,11 @@ void board_reset(void)
au_writel(0x00000000, PB1100_RST_VDDI);
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
......
......@@ -30,8 +30,6 @@
#include <prom.h>
#include <au1xxx.h>
extern void _board_init_irq(void);
extern void (*board_init_irq)(void);
const char *get_system_type(void)
{
......@@ -131,9 +129,6 @@ void __init board_setup(void)
#ifdef CONFIG_MIPS_DB1200
printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
#endif
/* Setup Pb1200 External Interrupt Controller */
board_init_irq = _board_init_irq;
}
int board_au1200fb_panel(void)
......
......@@ -40,10 +40,9 @@
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
/* This is external interrupt cascade */
{ AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_7, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
/*
* Support for External interrupts on the Pb1200 Development platform.
......@@ -121,10 +120,12 @@ static struct irq_chip external_irq_type = {
.unmask = pb1200_enable_irq,
};
void _board_init_irq(void)
void __init board_init_irq(void)
{
unsigned int irq;
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
#ifdef CONFIG_MIPS_PB1200
/* We have a problem with CPLD rev 3. */
if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
......
......@@ -25,6 +25,7 @@
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1500.h>
......@@ -38,15 +39,13 @@ char irq_tab_alchemy[][5] __initdata = {
};
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
{ AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
const char *get_system_type(void)
{
......@@ -59,6 +58,11 @@ void board_reset(void)
au_writel(0x00000000, PB1500_RST_VDDI);
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
u32 pin_func;
......
......@@ -28,6 +28,7 @@
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1550.h>
......@@ -41,13 +42,10 @@ char irq_tab_alchemy[][5] __initdata = {
};
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
const char *get_system_type(void)
{
return "Alchemy Pb1550";
......@@ -59,6 +57,11 @@ void board_reset(void)
au_writew(au_readw(0xAF00001C) & ~BCSR_SYSTEM_RESET, 0xAF00001C);
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
u32 pin_func;
......
......@@ -27,7 +27,7 @@
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
char irq_tab_alchemy[][5] __initdata = {
......@@ -42,11 +42,15 @@ char irq_tab_alchemy[][5] __initdata = {
};
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
{ AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
......@@ -27,23 +27,26 @@
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
{ AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_207, INTC_INT_LOW_LEVEL, 0 },
{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_207, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* CF interrupt */
{ AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 },
{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 },
{ AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* CF interrupt */
{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 },
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
......@@ -109,10 +109,11 @@ struct au1xxx_irqmap {
int im_request;
};
/*
* init_IRQ looks for a table with this name.
*/
extern struct au1xxx_irqmap au1xxx_irq_map[];
/* core calls this function to let boards initialize other IRQ sources */
void board_init_irq(void);
/* boards call this to register additional (GPIO) interrupts */
void au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count);
#endif /* !defined (_LANGUAGE_ASSEMBLY) */
......@@ -505,15 +506,6 @@ extern struct au1xxx_irqmap au1xxx_irq_map[];
#define IC1_TESTBIT 0xB1800080
/* Interrupt Configuration Modes */
#define INTC_INT_DISABLED 0x0
#define INTC_INT_RISE_EDGE 0x1
#define INTC_INT_FALL_EDGE 0x2
#define INTC_INT_RISE_AND_FALL_EDGE 0x3
#define INTC_INT_HIGH_LEVEL 0x5
#define INTC_INT_LOW_LEVEL 0x6
#define INTC_INT_HIGH_AND_LOW_LEVEL 0x7
/* Interrupt Numbers */
/* Au1000 */
#ifdef CONFIG_SOC_AU1000
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment