Commit 314489bd authored by Linus Torvalds's avatar Linus Torvalds
Browse files

Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: SoC fixes: from Olof Johansson:
 "A bunch of fixes for regressions (and a few other problems) in
  3.4-rc1:

 - Fix for regression of mach/io.h cleanup on platforms with PCI or
   PCMCIA (adding back the include file on those for now)
 - AT91 fixes for usb and spi
 - smsc911x ethernet fixes for i.MX
 - smsc911x fixes for OMAP
 - gpio fixes for Tegra
 - A handful of build error and warning fixes for various platforms
 - cpufreq kconfig dependencies, build and lowlevel debug fixes for
   Samsung platforms

  In other words, more or less the regular collection of -rc1/2 type
  material.  A few of them, in particular the smsc911x for OMAP series,
  aren't technically regressions for 3.4, but they're valid fixes and
  we're still relatively early in the rc cycle so it seems appropriate
  to include them."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
  ARM: fix __io macro for PCMCIA
  ARM: EXYNOS: Fix compiler warning in dma.c file
  ARM: EXYNOS: fix ISO C90 warning
  ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
  ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
  ARM: OMAP2+: hwmod: Restore sysc after a reset
  ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
  ARM: OMAP3: clock data: fill in some missing clockdomains
  ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
  ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
  ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
  gpio: tegra: Iterate over the correct number of banks
  gpio: tegra: fix register address calculations for Tegra30
  EXYNOS: fix dependency for EXYNOS_CPUFREQ
  ARM: at91: dt: remove unit-address part for memory nodes
  ARM: at91: fix check of valid GPIO for SPI and USB
  USB: ehci-atmel: add needed of.h header file
  ARM: at91/NAND DT bindings: add comments
  ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
  USB: ohci-at91: trivial return code name change
  ...
parents 43e347a1 a8f5b6e5
......@@ -27,13 +27,13 @@ nand0: nand@40000000,0 {
reg = <0x40000000 0x10000000
0xffffe800 0x200
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
atmel,nand-addr-offset = <21>; /* ale */
atmel,nand-cmd-offset = <22>; /* cle */
nand-on-flash-bbt;
nand-ecc-mode = "soft";
gpios = <&pioC 13 0
&pioC 14 0
0
gpios = <&pioC 13 0 /* rdy */
&pioC 14 0 /* nce */
0 /* cd */
>;
partition@0 {
...
......
......@@ -338,6 +338,7 @@ config ARCH_AT91
select HAVE_CLK
select CLKDEV_LOOKUP
select IRQ_DOMAIN
select NEED_MACH_IO_H if PCCARD
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 processors.
......
......@@ -35,7 +35,7 @@
};
};
memory@20000000 {
memory {
reg = <0x20000000 0x08000000>;
};
......
......@@ -37,8 +37,8 @@
usb0: ohci@00600000 {
status = "okay";
num-ports = <2>;
atmel,vbus-gpio = <&pioD 19 0
&pioD 20 0
atmel,vbus-gpio = <&pioD 19 1
&pioD 20 1
>;
};
......
......@@ -36,7 +36,7 @@
};
};
memory@70000000 {
memory {
reg = <0x70000000 0x10000000>;
};
......
......@@ -17,7 +17,7 @@
bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
};
memory@70000000 {
memory {
reg = <0x70000000 0x4000000>;
};
......@@ -73,8 +73,8 @@
usb0: ohci@00700000 {
status = "okay";
num-ports = <2>;
atmel,vbus-gpio = <&pioD 1 0
&pioD 3 0>;
atmel,vbus-gpio = <&pioD 1 1
&pioD 3 1>;
};
usb1: ehci@00800000 {
......
......@@ -34,7 +34,7 @@
};
};
memory@20000000 {
memory {
reg = <0x20000000 0x10000000>;
};
......@@ -201,8 +201,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
gpios = <&pioC 8 0
&pioC 14 0
gpios = <&pioD 5 0
&pioD 4 0
0
>;
status = "disabled";
......
......@@ -8,7 +8,7 @@
*/
/ {
memory@20000000 {
memory {
reg = <0x20000000 0x8000000>;
};
......
......@@ -16,7 +16,7 @@
bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
};
memory@20000000 {
memory {
reg = <0x20000000 0x4000000>;
};
......
......@@ -2,6 +2,7 @@
#define __ASM_BARRIER_H
#ifndef __ASSEMBLY__
#include <asm/outercache.h>
#define nop() __asm__ __volatile__("mov\tr0,r0\t@ nop\n\t");
......@@ -39,7 +40,6 @@
#ifdef CONFIG_ARCH_HAS_BARRIERS
#include <mach/barriers.h>
#elif defined(CONFIG_ARM_DMA_MEM_BUFFERABLE) || defined(CONFIG_SMP)
#include <asm/outercache.h>
#define mb() do { dsb(); outer_sync(); } while (0)
#define rmb() dsb()
#define wmb() mb()
......
......@@ -119,7 +119,7 @@ static inline void __iomem *__typesafe_io(unsigned long addr)
#ifdef CONFIG_NEED_MACH_IO_H
#include <mach/io.h>
#else
#define __io(a) ({ (void)(a); __typesafe_io(0); })
#define __io(a) __typesafe_io((a) & IO_SPACE_LIMIT)
#endif
/*
......
......@@ -598,6 +598,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
else
cs_pin = spi1_standard_cs[devices[i].chip_select];
if (!gpio_is_valid(cs_pin))
continue;
if (devices[i].bus_num == 0)
enable_spi0 = 1;
else
......
......@@ -415,6 +415,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
else
cs_pin = spi1_standard_cs[devices[i].chip_select];
if (!gpio_is_valid(cs_pin))
continue;
if (devices[i].bus_num == 0)
enable_spi0 = 1;
else
......
......@@ -72,7 +72,8 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
at91_set_gpio_output(data->vbus_pin[i],
data->vbus_pin_active_low[i]);
}
/* Enable overcurrent notification */
......@@ -671,6 +672,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
else
cs_pin = spi1_standard_cs[devices[i].chip_select];
if (!gpio_is_valid(cs_pin))
continue;
if (devices[i].bus_num == 0)
enable_spi0 = 1;
else
......
......@@ -127,12 +127,13 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
at91_set_gpio_output(data->vbus_pin[i],
data->vbus_pin_active_low[i]);
}
/* Enable overcurrent notification */
for (i = 0; i < data->ports; i++) {
if (data->overcurrent_pin[i])
if (gpio_is_valid(data->overcurrent_pin[i]))
at91_set_gpio_input(data->overcurrent_pin[i], 1);
}
......@@ -188,7 +189,8 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
at91_set_gpio_output(data->vbus_pin[i],
data->vbus_pin_active_low[i]);
}
usbh_ehci_data = *data;
......@@ -785,6 +787,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
else
cs_pin = spi1_standard_cs[devices[i].chip_select];
if (!gpio_is_valid(cs_pin))
continue;
if (devices[i].bus_num == 0)
enable_spi0 = 1;
else
......
......@@ -419,6 +419,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
else
cs_pin = spi_standard_cs[devices[i].chip_select];
if (!gpio_is_valid(cs_pin))
continue;
/* enable chip-select pin */
at91_set_gpio_output(cs_pin, 1);
......
......@@ -223,6 +223,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb0_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma0_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffee00.dma-controller", &dma1_clk),
CLKDEV_CON_ID("pioA", &pioAB_clk),
CLKDEV_CON_ID("pioB", &pioAB_clk),
CLKDEV_CON_ID("pioC", &pioCD_clk),
......
......@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
.vbus_pin_active_low = {1, 1},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
......
......@@ -71,6 +71,7 @@ static void __init ek_init_early(void)
static struct at91_usbh_data __initdata ek_usbh_hs_data = {
.ports = 2,
.vbus_pin = {AT91_PIN_PD1, AT91_PIN_PD3},
.vbus_pin_active_low = {1, 1},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
......
......@@ -86,14 +86,15 @@ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *d
extern void __init at91_add_device_eth(struct macb_platform_data *data);
/* USB Host */
#define AT91_MAX_USBH_PORTS 3
struct at91_usbh_data {
u8 ports; /* number of ports on root hub */
int vbus_pin[2]; /* port power-control pin */
u8 vbus_pin_active_low[2];
int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */
int overcurrent_pin[AT91_MAX_USBH_PORTS];
u8 ports; /* number of ports on root hub */
u8 overcurrent_supported;
int overcurrent_pin[2];
u8 overcurrent_status[2];
u8 overcurrent_changed[2];
u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS];
u8 overcurrent_status[AT91_MAX_USBH_PORTS];
u8 overcurrent_changed[AT91_MAX_USBH_PORTS];
};
extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment