Commit 1c1452be authored by Jonas Larsson's avatar Jonas Larsson Committed by Haavard Skinnemoen

atmel-mci: Add support for inverted detect pin

Same patch as before, modified to use bool. Also adds description of
the new field in struct atmel_mci that I missed in the first patch.

This patch adds Atmel MCI support for inverted detect pins.
Signed-off-by: default avatarJonas Larsson <jonas.larsson@martinsson.se>
Acked-by: default avatarPierre Ossman <pierre@ossman.eu>
Signed-off-by: default avatarHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
parent 577c9c45
......@@ -177,6 +177,7 @@ struct atmel_mci {
* available.
* @wp_pin: GPIO pin used for card write protect sending, or negative
* if not available.
* @detect_is_active_high: The state of the detect pin when it is active.
* @detect_timer: Timer used for debouncing @detect_pin interrupts.
*/
struct atmel_mci_slot {
......@@ -196,6 +197,7 @@ struct atmel_mci_slot {
int detect_pin;
int wp_pin;
bool detect_is_active_high;
struct timer_list detect_timer;
};
......@@ -924,7 +926,8 @@ static int atmci_get_cd(struct mmc_host *mmc)
struct atmel_mci_slot *slot = mmc_priv(mmc);
if (gpio_is_valid(slot->detect_pin)) {
present = !gpio_get_value(slot->detect_pin);
present = !(gpio_get_value(slot->detect_pin) ^
slot->detect_is_active_high);
dev_dbg(&mmc->class_dev, "card is %spresent\n",
present ? "" : "not ");
}
......@@ -1028,7 +1031,8 @@ static void atmci_detect_change(unsigned long data)
return;
enable_irq(gpio_to_irq(slot->detect_pin));
present = !gpio_get_value(slot->detect_pin);
present = !(gpio_get_value(slot->detect_pin) ^
slot->detect_is_active_high);
present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
......@@ -1456,6 +1460,7 @@ static int __init atmci_init_slot(struct atmel_mci *host,
slot->host = host;
slot->detect_pin = slot_data->detect_pin;
slot->wp_pin = slot_data->wp_pin;
slot->detect_is_active_high = slot_data->detect_is_active_high;
slot->sdc_reg = sdc_reg;
mmc->ops = &atmci_ops;
......@@ -1477,7 +1482,8 @@ static int __init atmci_init_slot(struct atmel_mci *host,
if (gpio_request(slot->detect_pin, "mmc_detect")) {
dev_dbg(&mmc->class_dev, "no detect pin available\n");
slot->detect_pin = -EBUSY;
} else if (gpio_get_value(slot->detect_pin)) {
} else if (gpio_get_value(slot->detect_pin) ^
slot->detect_is_active_high) {
clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
}
}
......
......@@ -10,6 +10,7 @@
* @bus_width: Number of data lines wired up the slot
* @detect_pin: GPIO pin wired to the card detect switch
* @wp_pin: GPIO pin wired to the write protect sensor
* @detect_is_active_high: The state of the detect pin when it is active
*
* If a given slot is not present on the board, @bus_width should be
* set to 0. The other fields are ignored in this case.
......@@ -24,6 +25,7 @@ struct mci_slot_pdata {
unsigned int bus_width;
int detect_pin;
int wp_pin;
bool detect_is_active_high;
};
/**
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment