mac80211.h 101 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
6
 * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
22
#include <linux/inetdevice.h>
23 24
#include <net/cfg80211.h>

25 26 27 28 29 30 31 32 33 34 35 36 37
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
38 39 40
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
41 42 43 44
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
45
 *	 use the non-IRQ-safe functions!
46 47
 */

48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
74 75
 */

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
/**
 * DOC: mac80211 workqueue
 *
 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
 * The workqueue is a single threaded workqueue and can only be accessed by
 * helpers for sanity checking. Drivers must ensure all work added onto the
 * mac80211 workqueue should be cancelled on the driver stop() callback.
 *
 * mac80211 will flushed the workqueue upon interface removal and during
 * suspend.
 *
 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
 *
 */

Johannes Berg's avatar
Johannes Berg committed
91 92 93 94 95 96
/**
 * enum ieee80211_max_queues - maximum number of queues
 *
 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
 */
enum ieee80211_max_queues {
97
	IEEE80211_MAX_QUEUES =		4,
Johannes Berg's avatar
Johannes Berg committed
98 99
};

100 101 102 103
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
104
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
105
 *
106
 * @aifs: arbitration interframe space [0..255]
107 108
 * @cw_min: minimum contention window [a value of the form
 *	2^n-1 in the range 1..32767]
109
 * @cw_max: maximum contention window [like @cw_min]
110
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
111
 * @uapsd: is U-APSD mode enabled for the queue
112
 */
113
struct ieee80211_tx_queue_params {
114
	u16 txop;
115 116
	u16 cw_min;
	u16 cw_max;
117
	u8 aifs;
118
	bool uapsd;
119 120 121 122 123 124 125 126 127
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

128 129 130 131 132 133 134 135 136 137
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
138
 * @BSS_CHANGED_ERP_SLOT: slot timing changed
Tomas Winkler's avatar
Tomas Winkler committed
139
 * @BSS_CHANGED_HT: 802.11n parameters changed
140
 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
141
 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
142 143 144 145 146 147
 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
 *	reason (IBSS and managed mode)
 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
 *	new beacon (beaconing modes)
 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
 *	enabled/disabled (beaconing modes)
148
 * @BSS_CHANGED_CQM: Connection quality monitor config changed
149
 * @BSS_CHANGED_IBSS: IBSS join status changed
150 151 152 153 154
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
155
	BSS_CHANGED_ERP_SLOT		= 1<<3,
Tomas Winkler's avatar
Tomas Winkler committed
156
	BSS_CHANGED_HT                  = 1<<4,
157
	BSS_CHANGED_BASIC_RATES		= 1<<5,
158
	BSS_CHANGED_BEACON_INT		= 1<<6,
159 160 161
	BSS_CHANGED_BSSID		= 1<<7,
	BSS_CHANGED_BEACON		= 1<<8,
	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
162
	BSS_CHANGED_CQM			= 1<<10,
163
	BSS_CHANGED_IBSS		= 1<<11,
164 165

	/* when adding here, make sure to change ieee80211_reconfig */
166 167 168 169 170 171 172 173 174
};

/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
175 176
 * @ibss_joined: indicates whether this station is part of an IBSS
 *	or not
177 178
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
179 180 181 182 183 184
 * @use_short_preamble: use 802.11b short preamble;
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
 * @use_short_slot: use short slot time (only relevant for ERP);
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
185 186
 * @dtim_period: num of beacons before the next DTIM, for beaconing,
 *	not valid in station mode (cf. hw conf ps_dtim_period)
187 188
 * @timestamp: beacon timestamp
 * @beacon_int: beacon interval
189
 * @assoc_capability: capabilities taken from assoc resp
190 191 192
 * @basic_rates: bitmap of basic rates, each bit stands for an
 *	index into the rate table configured by the driver in
 *	the current band.
193 194
 * @bssid: The BSSID for this BSS
 * @enable_beacon: whether beaconing should be enabled or not
195 196 197
 * @channel_type: Channel type for this BSS -- the hardware might be
 *	configured for HT40+ while this BSS only uses no-HT, for
 *	example.
198 199
 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
 *	This field is only valid when the channel type is one of the HT types.
200 201 202
 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
 *	implies disabled
 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
203 204
 */
struct ieee80211_bss_conf {
205
	const u8 *bssid;
206
	/* association related data */
207
	bool assoc, ibss_joined;
208 209 210 211
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
212
	bool use_short_slot;
213
	bool enable_beacon;
214
	u8 dtim_period;
215 216 217
	u16 beacon_int;
	u16 assoc_capability;
	u64 timestamp;
218
	u32 basic_rates;
219
	u16 ht_operation_mode;
220 221
	s32 cqm_rssi_thold;
	u32 cqm_rssi_hyst;
222
	enum nl80211_channel_type channel_type;
223 224
};

225
/**
226
 * enum mac80211_tx_control_flags - flags to describe transmission information/status
227
 *
228
 * These flags are used with the @flags member of &ieee80211_tx_info.
229
 *
230
 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
231 232 233 234 235 236 237 238 239 240 241
 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
 *	number to this frame, taking care of not overwriting the fragment
 *	number and increasing the sequence number only when the
 *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
 *	assign sequence numbers to QoS-data frames but cannot do so correctly
 *	for non-QoS-data and management frames because beacons need them from
 *	that counter as well and mac80211 cannot guarantee proper sequencing.
 *	If this flag is set, the driver should instruct the hardware to
 *	assign a sequence number to the frame or assign one itself. Cf. IEEE
 *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
 *	beacons and always be clear for frames without a sequence number field.
242 243 244 245 246 247
 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
 *	station
 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
248
 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
249
 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
250 251 252 253 254 255 256 257
 *	because the destination STA was in powersave mode. Note that to
 *	avoid race conditions, the filter must be set by the hardware or
 *	firmware upon receiving a frame that indicates that the station
 *	went to sleep (must be done on device to filter frames already on
 *	the queue) and may only be unset after mac80211 gives the OK for
 *	that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
 *	since only then is it guaranteed that no more frames are in the
 *	hardware queue.
258 259 260
 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
261 262
 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
 * 	so consider using block ack request (BAR).
263 264 265
 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
 *	set by rate control algorithms to indicate probe rate, will
 *	be cleared for fragmented frames (except on the last fragment)
266 267 268
 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
 *	used to indicate that a pending frame requires TX processing before
 *	it can be sent out.
269 270
 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
 *	used to indicate that a frame was already retried due to PS
Johannes Berg's avatar
Johannes Berg committed
271 272
 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
 *	used to indicate frame should not be encrypted
273 274 275
 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
 *	This frame is a response to a PS-poll frame and should be sent
 *	although the station is in powersave mode.
276 277 278 279
 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
 *	transmit function after the current frame, this can be used
 *	by drivers to kick the DMA queue only if unset or when the
 *	queue gets full.
280 281 282
 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
 *	after TX status because the destination was asleep, it must not
 *	be modified again (no seqno assignment, crypto, etc.)
283 284
 * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still
 *	has a radiotap header at skb->data.
285 286 287
 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
 *	MLME command (internal to mac80211 to figure out whether to send TX
 *	status to user space)
288
 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
289 290
 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
 *	frame and selects the maximum number of streams that it can use.
291 292
 */
enum mac80211_tx_control_flags {
293
	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
294 295 296 297 298 299 300 301 302 303 304 305
	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
	IEEE80211_TX_CTL_AMPDU			= BIT(6),
	IEEE80211_TX_CTL_INJECTED		= BIT(7),
	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
	IEEE80211_TX_STAT_ACK			= BIT(9),
	IEEE80211_TX_STAT_AMPDU			= BIT(10),
	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
306
	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
307
	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
Johannes Berg's avatar
Johannes Berg committed
308
	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
309
	IEEE80211_TX_CTL_PSPOLL_RESPONSE	= BIT(17),
310
	IEEE80211_TX_CTL_MORE_FRAMES		= BIT(18),
311
	IEEE80211_TX_INTFL_RETRANSMISSION	= BIT(19),
312
	IEEE80211_TX_INTFL_HAS_RADIOTAP		= BIT(20),
313
	IEEE80211_TX_INTFL_NL80211_FRAME_TX	= BIT(21),
314
	IEEE80211_TX_CTL_LDPC			= BIT(22),
315 316
	IEEE80211_TX_CTL_STBC			= BIT(23) | BIT(24),
#define IEEE80211_TX_CTL_STBC_SHIFT		23
317 318
};

319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338
/**
 * enum mac80211_rate_control_flags - per-rate flags set by the
 *	Rate Control algorithm.
 *
 * These flags are set by the Rate control algorithm for each rate during tx,
 * in the @flags member of struct ieee80211_tx_rate.
 *
 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
 *	This is set if the current BSS requires ERP protection.
 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
 * @IEEE80211_TX_RC_MCS: HT rate.
 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
 *	Greenfield mode.
 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
 *	adjacent 20 MHz channels, if the current channel type is
 *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
 */
339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354
enum mac80211_rate_control_flags {
	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),

	/* rate index is an MCS rate number instead of an index */
	IEEE80211_TX_RC_MCS			= BIT(3),
	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
};


/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
355

356 357
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
358

359 360
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES	5
361 362

/**
363
 * struct ieee80211_tx_rate - rate selection/status
364
 *
365 366
 * @idx: rate index to attempt to send with
 * @flags: rate control flags (&enum mac80211_rate_control_flags)
367
 * @count: number of tries in this rate before going to the next rate
368 369 370 371 372 373
 *
 * A value of -1 for @idx indicates an invalid rate and, if used
 * in an array of retry rates, that no more rates should be tried.
 *
 * When used for transmit status reporting, the driver should
 * always report the rate along with the flags it used.
374 375 376 377 378 379 380 381 382 383 384 385 386 387 388
 *
 * &struct ieee80211_tx_info contains an array of these structs
 * in the control information, and it will be filled by the rate
 * control algorithm according to what should be sent. For example,
 * if this array contains, in the format { <idx>, <count> } the
 * information
 *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
 * then this means that the frame should be transmitted
 * up to twice at rate 3, up to twice at rate 2, and up to four
 * times at rate 1 if it doesn't get acknowledged. Say it gets
 * acknowledged by the peer after the fifth attempt, the status
 * information should then contain
 *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
 * since it was transmitted twice at rate 3, twice at rate 2
 * and once at rate 1 after which we received an acknowledgement.
389
 */
390 391 392 393
struct ieee80211_tx_rate {
	s8 idx;
	u8 count;
	u8 flags;
394
} __attribute__((packed));
395

396 397 398 399 400 401 402 403
/**
 * struct ieee80211_tx_info - skb transmit information
 *
 * This structure is placed in skb->cb for three uses:
 *  (1) mac80211 TX control - mac80211 tells the driver what to do
 *  (2) driver internal use (if applicable)
 *  (3) TX status information - driver tells mac80211 what happened
 *
404 405 406
 * The TX control's sta pointer is only valid during the ->tx call,
 * it may be NULL.
 *
407
 * @flags: transmit info flags, defined above
408
 * @band: the band to transmit on (use for checking for races)
409
 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
410
 * @pad: padding, ignore
411 412 413
 * @control: union for control data
 * @status: union for status data
 * @driver_data: array of driver_data pointers
414
 * @ampdu_ack_len: number of acked aggregated frames.
415
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
416
 * @ampdu_len: number of aggregated frames.
417
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
418
 * @ack_signal: signal strength of the ACK frame
419
 */
420 421 422 423
struct ieee80211_tx_info {
	/* common information */
	u32 flags;
	u8 band;
424

425
	u8 antenna_sel_tx;
426

427
	/* 2 byte hole */
428
	u8 pad[2];
429 430 431

	union {
		struct {
432 433 434 435 436 437 438 439 440 441
			union {
				/* rate control */
				struct {
					struct ieee80211_tx_rate rates[
						IEEE80211_TX_MAX_RATES];
					s8 rts_cts_rate_idx;
				};
				/* only needed before rate control */
				unsigned long jiffies;
			};
442
			/* NB: vif can be NULL for injected frames */
443 444
			struct ieee80211_vif *vif;
			struct ieee80211_key_conf *hw_key;
445
			struct ieee80211_sta *sta;
446 447
		} control;
		struct {
448 449
			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
			u8 ampdu_ack_len;
450
			int ack_signal;
451
			u8 ampdu_len;
452
			/* 15 bytes free */
453
		} status;
454 455 456 457 458 459 460 461
		struct {
			struct ieee80211_tx_rate driver_rates[
				IEEE80211_TX_MAX_RATES];
			void *rate_driver_data[
				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
		};
		void *driver_data[
			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
462
	};
463 464
};

465 466 467 468
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
	return (struct ieee80211_tx_info *)skb->cb;
}
469

470 471 472 473 474
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
	return (struct ieee80211_rx_status *)skb->cb;
}

475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509
/**
 * ieee80211_tx_info_clear_status - clear TX status
 *
 * @info: The &struct ieee80211_tx_info to be cleared.
 *
 * When the driver passes an skb back to mac80211, it must report
 * a number of things in TX status. This function clears everything
 * in the TX status but the rate control information (it does clear
 * the count since you need to fill that in anyway).
 *
 * NOTE: You can only use this function if you do NOT use
 *	 info->driver_data! Use info->rate_driver_data
 *	 instead if you need only the less space that allows.
 */
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
	int i;

	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, control.rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, driver_rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
	/* clear the rate counts */
	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
		info->status.rates[i].count = 0;

	BUILD_BUG_ON(
	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
	memset(&info->status.ampdu_ack_len, 0,
	       sizeof(struct ieee80211_tx_info) -
	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}

510 511 512 513 514 515 516 517 518 519 520 521 522

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
523 524 525 526
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
527
 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
Bruno Randolf's avatar
Bruno Randolf committed
528 529
 *	is valid. This is useful in monitor mode and necessary for beacon frames
 *	to enable IBSS merging.
530
 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
531 532 533
 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
 * @RX_FLAG_SHORT_GI: Short guard interval was used
534 535 536
 * @RX_FLAG_INTERNAL_CMTR: set internally after frame was reported
 *	on cooked monitor to avoid double-reporting it for multiple
 *	virtual interfaces
537 538 539 540 541 542
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
543 544
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
545
	RX_FLAG_TSFT		= 1<<7,
546 547 548 549
	RX_FLAG_SHORTPRE	= 1<<8,
	RX_FLAG_HT		= 1<<9,
	RX_FLAG_40MHZ		= 1<<10,
	RX_FLAG_SHORT_GI	= 1<<11,
550
	RX_FLAG_INTERNAL_CMTR	= 1<<12,
551 552 553 554 555 556 557
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
558
 * frame, in the skb's control buffer (cb).
559
 *
560 561
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
562
 * @band: the active band when this frame was received
563
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
564 565 566
 * @signal: signal strength when receiving this frame, either in dBm, in dB or
 *	unspecified depending on the hardware capabilities flags
 *	@IEEE80211_HW_SIGNAL_*
567
 * @antenna: antenna used
568 569
 * @rate_idx: index of data rate into band's supported rates or MCS index if
 *	HT rates are use (RX_FLAG_HT)
570 571
 * @flag: %RX_FLAG_*
 */
572 573
struct ieee80211_rx_status {
	u64 mactime;
574
	enum ieee80211_band band;
575 576
	int freq;
	int signal;
577
	int antenna;
578
	int rate_idx;
579 580 581
	int flag;
};

582 583 584 585 586
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
587 588 589
 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
 *	to determine for example whether to calculate timestamps for packets
 *	or not, do not use instead of filter flags!
590 591 592 593 594 595 596
 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
 *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
 *	meaning that the hardware still wakes up for beacons, is able to
 *	transmit frames and receive the possible acknowledgment frames.
 *	Not to be confused with hardware specific wakeup/sleep states,
 *	driver is responsible for that. See the section "Powersave support"
 *	for more.
597 598 599 600 601
 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
 *	the driver should be prepared to handle configuration requests but
 *	may turn the device off as much as possible. Typically, this flag will
 *	be set when an interface is set UP but not associated or scanning, but
 *	it can also be unset in that case when monitor interfaces are active.
602 603 604
 * @IEEE80211_CONF_QOS: Enable 802.11e QoS also know as WMM (Wireless
 *      Multimedia). On some drivers (iwlwifi is one of know) we have
 *      to enable/disable QoS explicitly.
605 606
 */
enum ieee80211_conf_flags {
607
	IEEE80211_CONF_MONITOR		= (1<<0),
Johannes Berg's avatar
Johannes Berg committed
608
	IEEE80211_CONF_PS		= (1<<1),
609
	IEEE80211_CONF_IDLE		= (1<<2),
610
	IEEE80211_CONF_QOS		= (1<<3),
611
};
612

613

614 615 616 617
/**
 * enum ieee80211_conf_changed - denotes which configuration changed
 *
 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
618
 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
619
 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
620
 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
621
 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
622
 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
623
 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
624
 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
625
 * @IEEE80211_CONF_CHANGE_QOS: Quality of service was enabled or disabled
626 627
 */
enum ieee80211_conf_changed {
628
	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
629
	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
630
	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
631
	IEEE80211_CONF_CHANGE_PS		= BIT(4),
632 633 634
	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
635
	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
636
	IEEE80211_CONF_CHANGE_QOS		= BIT(9),
637 638
};

639 640 641
/**
 * enum ieee80211_smps_mode - spatial multiplexing power save mode
 *
642 643 644 645 646
 * @IEEE80211_SMPS_AUTOMATIC: automatic
 * @IEEE80211_SMPS_OFF: off
 * @IEEE80211_SMPS_STATIC: static
 * @IEEE80211_SMPS_DYNAMIC: dynamic
 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
647 648 649 650 651 652 653 654 655 656 657
 */
enum ieee80211_smps_mode {
	IEEE80211_SMPS_AUTOMATIC,
	IEEE80211_SMPS_OFF,
	IEEE80211_SMPS_STATIC,
	IEEE80211_SMPS_DYNAMIC,

	/* keep last */
	IEEE80211_SMPS_NUM_MODES,
};

658 659 660 661 662
/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
663 664
 * @flags: configuration flags defined above
 *
665
 * @listen_interval: listen interval in units of beacon interval
666
 * @max_sleep_period: the maximum number of beacon intervals to sleep for
667 668 669 670
 *	before checking the beacon for a TIM bit (managed mode only); this
 *	value will be only achievable between DTIM frames, the hardware
 *	needs to check for the multicast traffic bit in DTIM beacons.
 *	This variable is valid only when the CONF_PS flag is set.
671 672 673
 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
 *	in power saving. Power saving will not be enabled until a beacon
 *	has been received and the DTIM period is known.
674 675 676
 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
 *	powersave documentation below. This variable is valid only when
 *	the CONF_PS flag is set.
677 678 679
 * @dynamic_ps_forced_timeout: The dynamic powersave timeout (in ms) configured
 *	by cfg80211 (essentially, wext) If set, this value overrules the value
 *	chosen by mac80211 based on ps qos network latency.
680
 *
681
 * @power_level: requested transmit power (in dBm)
682
 *
683
 * @channel: the channel to tune to
684
 * @channel_type: the channel (HT) type
685
 *
686 687 688 689 690 691
 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
 *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
 *    but actually means the number of transmissions not the number of retries
 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
 *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
 *    number of transmissions not the number of retries
692 693 694 695
 *
 * @smps_mode: spatial multiplexing powersave mode; note that
 *	%IEEE80211_SMPS_STATIC is used when the device is not
 *	configured for an HT channel
696 697
 */
struct ieee80211_conf {
698
	u32 flags;
699
	int power_level, dynamic_ps_timeout, dynamic_ps_forced_timeout;
700
	int max_sleep_period;
701

702
	u16 listen_interval;
703
	u8 ps_dtim_period;
704

705 706
	u8 long_frame_max_tx_count, short_frame_max_tx_count;

707
	struct ieee80211_channel *channel;
708
	enum nl80211_channel_type channel_type;
709
	enum ieee80211_smps_mode smps_mode;
710 711
};

712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733
/**
 * struct ieee80211_channel_switch - holds the channel switch data
 *
 * The information provided in this structure is required for channel switch
 * operation.
 *
 * @timestamp: value in microseconds of the 64-bit Time Synchronization
 *	Function (TSF) timer when the frame containing the channel switch
 *	announcement was received. This is simply the rx.mactime parameter
 *	the driver passed into mac80211.
 * @block_tx: Indicates whether transmission must be blocked before the
 *	scheduled channel switch, as indicated by the AP.
 * @channel: the new channel to switch to
 * @count: the number of TBTT's until the channel switch event
 */
struct ieee80211_channel_switch {
	u64 timestamp;
	bool block_tx;
	struct ieee80211_channel *channel;
	u8 count;
};

734 735 736 737 738 739
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
740
 * @type: type of this virtual interface
741 742
 * @bss_conf: BSS configuration for this interface, either our own
 *	or the BSS we're associated to
743
 * @addr: address of this interface
744 745 746 747
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
748
	enum nl80211_iftype type;
749
	struct ieee80211_bss_conf bss_conf;
750
	u8 addr[ETH_ALEN];
751 752 753 754
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

Johannes Berg's avatar
Johannes Berg committed
755 756 757
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
758
	return vif->type == NL80211_IFTYPE_MESH_POINT;
Johannes Berg's avatar
Johannes Berg committed
759 760 761 762
#endif
	return false;
}

763 764 765 766 767
/**
 * enum ieee80211_key_alg - key algorithm
 * @ALG_WEP: WEP40 or WEP104
 * @ALG_TKIP: TKIP
 * @ALG_CCMP: CCMP (AES)
768
 * @ALG_AES_CMAC: AES-128-CMAC
769
 */
770
enum ieee80211_key_alg {
771 772 773
	ALG_WEP,
	ALG_TKIP,
	ALG_CCMP,
774
	ALG_AES_CMAC,
775
};
776

777 778 779 780 781 782 783 784 785 786 787 788 789 790
/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
791 792
 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
 *	that the key is pairwise rather then a shared key.
793 794 795
 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
 *	CCMP key if it requires CCMP encryption of management frames (MFP) to
 *	be done in software.
796
 */
797 798 799 800
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
801
	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
802
	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
803
};
804

805 806 807 808 809 810 811 812
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
813
 *	encrypted in hardware.
814 815
 * @alg: The key algorithm.
 * @flags: key flags, see &enum ieee80211_key_flags.
816
 * @ap_addr: AP's MAC address
817 818
 * @keyidx: the key index (0-3)
 * @keylen: key material length
819 820 821 822 823
 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
 * 	data block:
 * 	- Temporal Encryption Key (128 bits)
 * 	- Temporal Authenticator Tx MIC Key (64 bits)
 * 	- Temporal Authenticator Rx MIC Key (64 bits)
824 825
 * @icv_len: The ICV length for this key type
 * @iv_len: The IV length for this key type
826
 */
827
struct ieee80211_key_conf {
828
	enum ieee80211_key_alg alg;
829 830
	u8 icv_len;
	u8 iv_len;
831
	u8 hw_key_idx;
832 833 834
	u8 flags;
	s8 keyidx;
	u8 keylen;
835 836 837
	u8 key[0];
};

838 839 840 841 842 843 844 845 846
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
847
enum set_key_cmd {
848
	SET_KEY, DISABLE_KEY,
849
};
850

851 852 853 854 855 856 857 858
/**
 * struct ieee80211_sta - station table entry
 *
 * A station table entry represents a station we are possibly
 * communicating with. Since stations are RCU-managed in
 * mac80211, any ieee80211_sta pointer you get access to must
 * either be protected by rcu_read_lock() explicitly or implicitly,
 * or you must take good care to not use such a pointer after a
859
 * call to your sta_remove callback that removed it.
860 861 862
 *
 * @addr: MAC address
 * @aid: AID we assigned to the station if we're an AP
863
 * @supp_rates: Bitmap of supported rates (per band)
Johannes Berg's avatar
Johannes Berg committed
864
 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
865 866 867 868
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *), size is determined in hw information.
 */
struct ieee80211_sta {
869
	u32 supp_rates[IEEE80211_NUM_BANDS];
870 871
	u8 addr[ETH_ALEN];
	u16 aid;
872
	struct ieee80211_sta_ht_cap ht_cap;
873 874 875 876 877

	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

878 879 880 881
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
882 883
 * indicates addition and removal of a station to station table,
 * or if a associated station made a power state transition.
884
 *
885 886
 * @STA_NOTIFY_ADD: (DEPRECATED) a station was added to the station table
 * @STA_NOTIFY_REMOVE: (DEPRECATED) a station being removed from the station table
887 888 889
 * @STA_NOTIFY_SLEEP: a station is now sleeping
 * @STA_NOTIFY_AWAKE: a sleeping station woke up
 */
890 891
enum sta_notify_cmd {
	STA_NOTIFY_ADD, STA_NOTIFY_REMOVE,
892 893 894
	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};

895 896 897 898 899 900 901 902 903 904 905 906 907 908 909
/**
 * enum ieee80211_tkip_key_type - get tkip key
 *
 * Used by drivers which need to get a tkip key for skb. Some drivers need a
 * phase 1 key, others need a phase 2 key. A single function allows the driver
 * to get the key, this enum indicates what type of key is required.
 *
 * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
 * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
 */
enum ieee80211_tkip_key_type {
	IEEE80211_TKIP_P1_KEY,
	IEEE80211_TKIP_P2_KEY,
};

910 911 912 913 914 915 916 917 918
/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
919 920 921 922 923 924 925 926 927 928 929 930 931
 * @IEEE80211_HW_HAS_RATE_CONTROL:
 *	The hardware or firmware includes rate control, and cannot be
 *	controlled by the stack. As such, no rate control algorithm
 *	should be instantiated, and the TX rate reported to userspace
 *	will be taken from the TX status instead of the rate control
 *	algorithm.
 *	Note that this requires that the driver implement a number of
 *	callbacks so it has the correct information, it needs to have
 *	the @set_rts_threshold callback and must look at the BSS config
 *	@use_cts_prot for G/N protection, @use_short_slot for slot
 *	timing in 2.4 GHz and @use_short_preamble for preambles for
 *	CCK frames.
 *
932 933 934 935 936 937 938 939 940 941
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
942
 *	the driver can fetch them with ieee80211_get_buffered_bc().
943
 *
944 945 946 947 948 949
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
950 951 952 953 954 955 956 957 958 959 960
 *
 * @IEEE80211_HW_SIGNAL_UNSPEC:
 *	Hardware can provide signal values but we don't know its units. We
 *	expect values between 0 and @max_signal.
 *	If possible please provide dB or dBm instead.
 *
 * @IEEE80211_HW_SIGNAL_DBM:
 *	Hardware gives signal values in dBm, decibel difference from
 *	one milliwatt. This is the preferred method since it is standardized
 *	between different devices. @max_signal does not need to be set.
 *
961 962 963
 * @IEEE80211_HW_SPECTRUM_MGMT:
 * 	Hardware supports spectrum management defined in 802.11h
 * 	Measurement, Channel Switch, Quieting, TPC
Sujith's avatar
Sujith committed
964 965 966
 *
 * @IEEE80211_HW_AMPDU_AGGREGATION:
 *	Hardware supports 11n A-MPDU aggregation.
967
 *
968 969 970 971 972 973 974 975 976
 * @IEEE80211_HW_SUPPORTS_PS:
 *	Hardware has power save support (i.e. can go to sleep).
 *
 * @IEEE80211_HW_PS_NULLFUNC_STACK:
 *	Hardware requires nullfunc frame handling in stack, implies
 *	stack support for dynamic PS.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
 *	Hardware has support for dynamic PS.
977 978 979
 *
 * @IEEE80211_HW_MFP_CAPABLE:
 *	Hardware supports management frame protection (MFP, IEEE 802.11w).
980 981 982 983
 *
 * @IEEE80211_HW_BEACON_FILTER:
 *	Hardware supports dropping of irrelevant beacon frames to
 *	avoid waking up cpu.
984 985 986 987 988 989 990 991 992 993
 *
 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
 *	Hardware supports static spatial multiplexing powersave,
 *	ie. can turn off all but one chain even on HT connections
 *	that should be using more chains.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
 *	Hardware supports dynamic spatial multiplexing powersave,
 *	ie. can turn off all but one chain and then wake the rest
 *	up as required after, for example, rts/cts handshake.
994 995 996 997 998
 *
 * @IEEE80211_HW_SUPPORTS_UAPSD:
 *	Hardware supports Unscheduled Automatic Power Save Delivery
 *	(U-APSD) in managed mode. The mode is configured with
 *	conf_tx() operation.
999 1000 1001 1002 1003
 *
 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
 *	Hardware can provide ack status reports of Tx frames to
 *	the stack.
 *
1004 1005 1006 1007 1008
 * @IEEE80211_HW_CONNECTION_MONITOR:
 *      The hardware performs its own connection monitoring, including
 *      periodic keep-alives to the AP and probing the AP on beacon loss.
 *      When this flag is set, signaling beacon-loss will cause an immediate
 *      change to disassociated state.
1009 1010 1011 1012 1013 1014
 *
 * @IEEE80211_HW_SUPPORTS_CQM_RSSI:
 *	Hardware can do connection quality monitoring - i.e. it can monitor
 *	connection quality related parameters, such as the RSSI level and
 *	provide notifications if configured trigger levels are reached.
 *
1015 1016
 */
enum ieee80211_hw_flags {
1017
	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
1018 1019
	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
1020 1021
	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
1022
	IEEE80211_HW_SIGNAL_UNSPEC			= 1<<5,
Johannes Berg's avatar
Johannes Berg committed
1023
	IEEE80211_HW_SIGNAL_DBM				= 1<<6,
1024
	/* use this hole */
Johannes Berg's avatar
Johannes Berg committed
1025 1026 1027 1028 1029 1030
	IEEE80211_HW_SPECTRUM_MGMT			= 1<<8,
	IEEE80211_HW_AMPDU_AGGREGATION			= 1<<9,
	IEEE80211_HW_SUPPORTS_PS			= 1<<10,
	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
1031
	IEEE80211_HW_BEACON_FILTER			= 1<<14,
1032 1033
	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
1034
	IEEE80211_HW_SUPPORTS_UAPSD			= 1<<17,
1035
	IEEE80211_HW_REPORTS_TX_ACK_STATUS		= 1<<18,
1036
	IEEE80211_HW_CONNECTION_MONITOR			= 1<<19,
1037
	IEEE80211_HW_SUPPORTS_CQM_RSSI			= 1<<20,
1038 1039
};

1040 1041
/**
 * struct ieee80211_hw - hardware information and state
1042 1043 1044 1045 1046 1047