mac80211.h 101 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
6
 * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/cfg80211.h>

24 25 26 27 28 29 30 31 32 33 34 35 36
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 38 39
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
40 41 42 43
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44
 *	 use the non-IRQ-safe functions!
45 46
 */

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
73 74
 */

75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
/**
 * DOC: mac80211 workqueue
 *
 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
 * The workqueue is a single threaded workqueue and can only be accessed by
 * helpers for sanity checking. Drivers must ensure all work added onto the
 * mac80211 workqueue should be cancelled on the driver stop() callback.
 *
 * mac80211 will flushed the workqueue upon interface removal and during
 * suspend.
 *
 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
 *
 */

Johannes Berg's avatar
Johannes Berg committed
90 91 92 93 94 95
/**
 * enum ieee80211_max_queues - maximum number of queues
 *
 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
 */
enum ieee80211_max_queues {
96
	IEEE80211_MAX_QUEUES =		4,
Johannes Berg's avatar
Johannes Berg committed
97 98
};

99 100 101 102
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
103
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
104
 *
105
 * @aifs: arbitration interframe space [0..255]
106 107
 * @cw_min: minimum contention window [a value of the form
 *	2^n-1 in the range 1..32767]
108
 * @cw_max: maximum contention window [like @cw_min]
109
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
110
 * @uapsd: is U-APSD mode enabled for the queue
111
 */
112
struct ieee80211_tx_queue_params {
113
	u16 txop;
114 115
	u16 cw_min;
	u16 cw_max;
116
	u8 aifs;
117
	bool uapsd;
118 119 120 121 122 123 124 125 126
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

127 128 129 130 131 132 133 134 135 136
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
137
 * @BSS_CHANGED_ERP_SLOT: slot timing changed
Tomas Winkler's avatar
Tomas Winkler committed
138
 * @BSS_CHANGED_HT: 802.11n parameters changed
139
 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
140
 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
141 142 143 144 145 146
 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
 *	reason (IBSS and managed mode)
 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
 *	new beacon (beaconing modes)
 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
 *	enabled/disabled (beaconing modes)
147
 * @BSS_CHANGED_CQM: Connection quality monitor config changed
148
 * @BSS_CHANGED_IBSS: IBSS join status changed
149
 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
150 151
 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
 *	that it is only ever disabled for station mode.
152 153 154 155 156
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
157
	BSS_CHANGED_ERP_SLOT		= 1<<3,
Tomas Winkler's avatar
Tomas Winkler committed
158
	BSS_CHANGED_HT                  = 1<<4,
159
	BSS_CHANGED_BASIC_RATES		= 1<<5,
160
	BSS_CHANGED_BEACON_INT		= 1<<6,
161 162 163
	BSS_CHANGED_BSSID		= 1<<7,
	BSS_CHANGED_BEACON		= 1<<8,
	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
164
	BSS_CHANGED_CQM			= 1<<10,
165
	BSS_CHANGED_IBSS		= 1<<11,
166
	BSS_CHANGED_ARP_FILTER		= 1<<12,
167
	BSS_CHANGED_QOS			= 1<<13,
168 169

	/* when adding here, make sure to change ieee80211_reconfig */
170 171
};

172 173 174 175 176 177 178
/*
 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
 * of addresses for an interface increase beyond this value, hardware ARP
 * filtering will be disabled.
 */
#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4

179 180 181 182 183 184 185
/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
186 187
 * @ibss_joined: indicates whether this station is part of an IBSS
 *	or not
188 189
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
190 191 192 193 194 195
 * @use_short_preamble: use 802.11b short preamble;
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
 * @use_short_slot: use short slot time (only relevant for ERP);
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
196 197
 * @dtim_period: num of beacons before the next DTIM, for beaconing,
 *	not valid in station mode (cf. hw conf ps_dtim_period)
198 199
 * @timestamp: beacon timestamp
 * @beacon_int: beacon interval
200
 * @assoc_capability: capabilities taken from assoc resp
201 202 203
 * @basic_rates: bitmap of basic rates, each bit stands for an
 *	index into the rate table configured by the driver in
 *	the current band.
204 205
 * @bssid: The BSSID for this BSS
 * @enable_beacon: whether beaconing should be enabled or not
206 207 208
 * @channel_type: Channel type for this BSS -- the hardware might be
 *	configured for HT40+ while this BSS only uses no-HT, for
 *	example.
209 210
 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
 *	This field is only valid when the channel type is one of the HT types.
211 212 213
 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
 *	implies disabled
 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
214 215 216 217 218 219 220 221 222
 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
 *	may filter ARP queries targeted for other addresses than listed here.
 *	The driver must allow ARP queries targeted for all address listed here
 *	to pass through. An empty list implies no ARP queries need to pass.
 * @arp_addr_cnt: Number of addresses currently on the list.
 * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may
 *	filter ARP queries based on the @arp_addr_list, if disabled, the
 *	hardware must not perform any ARP filtering. Note, that the filter will
 *	be enabled also in promiscuous mode.
223
 * @qos: This is a QoS-enabled BSS.
224 225
 */
struct ieee80211_bss_conf {
226
	const u8 *bssid;
227
	/* association related data */
228
	bool assoc, ibss_joined;
229 230 231 232
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
233
	bool use_short_slot;
234
	bool enable_beacon;
235
	u8 dtim_period;
236 237 238
	u16 beacon_int;
	u16 assoc_capability;
	u64 timestamp;
239
	u32 basic_rates;
240
	u16 ht_operation_mode;
241 242
	s32 cqm_rssi_thold;
	u32 cqm_rssi_hyst;
243
	enum nl80211_channel_type channel_type;
244 245 246
	__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
	u8 arp_addr_cnt;
	bool arp_filter_enabled;
247
	bool qos;
248 249
};

250
/**
251
 * enum mac80211_tx_control_flags - flags to describe transmission information/status
252
 *
253
 * These flags are used with the @flags member of &ieee80211_tx_info.
254
 *
255
 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
256 257 258 259 260 261 262 263 264 265 266
 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
 *	number to this frame, taking care of not overwriting the fragment
 *	number and increasing the sequence number only when the
 *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
 *	assign sequence numbers to QoS-data frames but cannot do so correctly
 *	for non-QoS-data and management frames because beacons need them from
 *	that counter as well and mac80211 cannot guarantee proper sequencing.
 *	If this flag is set, the driver should instruct the hardware to
 *	assign a sequence number to the frame or assign one itself. Cf. IEEE
 *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
 *	beacons and always be clear for frames without a sequence number field.
267 268 269 270 271 272
 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
 *	station
 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
273
 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
274
 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
275 276 277 278 279 280 281 282
 *	because the destination STA was in powersave mode. Note that to
 *	avoid race conditions, the filter must be set by the hardware or
 *	firmware upon receiving a frame that indicates that the station
 *	went to sleep (must be done on device to filter frames already on
 *	the queue) and may only be unset after mac80211 gives the OK for
 *	that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
 *	since only then is it guaranteed that no more frames are in the
 *	hardware queue.
283 284 285
 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
286 287
 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
 * 	so consider using block ack request (BAR).
288 289 290
 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
 *	set by rate control algorithms to indicate probe rate, will
 *	be cleared for fragmented frames (except on the last fragment)
291 292 293
 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
 *	used to indicate that a pending frame requires TX processing before
 *	it can be sent out.
294 295
 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
 *	used to indicate that a frame was already retried due to PS
Johannes Berg's avatar
Johannes Berg committed
296 297
 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
 *	used to indicate frame should not be encrypted
298 299 300
 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
 *	This frame is a response to a PS-poll frame and should be sent
 *	although the station is in powersave mode.
301 302 303 304
 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
 *	transmit function after the current frame, this can be used
 *	by drivers to kick the DMA queue only if unset or when the
 *	queue gets full.
305 306 307
 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
 *	after TX status because the destination was asleep, it must not
 *	be modified again (no seqno assignment, crypto, etc.)
308 309
 * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still
 *	has a radiotap header at skb->data.
310 311 312
 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
 *	MLME command (internal to mac80211 to figure out whether to send TX
 *	status to user space)
313
 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
314 315
 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
 *	frame and selects the maximum number of streams that it can use.
316 317
 */
enum mac80211_tx_control_flags {
318
	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
319 320 321 322 323 324 325 326 327 328 329 330
	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
	IEEE80211_TX_CTL_AMPDU			= BIT(6),
	IEEE80211_TX_CTL_INJECTED		= BIT(7),
	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
	IEEE80211_TX_STAT_ACK			= BIT(9),
	IEEE80211_TX_STAT_AMPDU			= BIT(10),
	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
331
	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
332
	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
Johannes Berg's avatar
Johannes Berg committed
333
	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
334
	IEEE80211_TX_CTL_PSPOLL_RESPONSE	= BIT(17),
335
	IEEE80211_TX_CTL_MORE_FRAMES		= BIT(18),
336
	IEEE80211_TX_INTFL_RETRANSMISSION	= BIT(19),
337
	IEEE80211_TX_INTFL_HAS_RADIOTAP		= BIT(20),
338
	IEEE80211_TX_INTFL_NL80211_FRAME_TX	= BIT(21),
339
	IEEE80211_TX_CTL_LDPC			= BIT(22),
340
	IEEE80211_TX_CTL_STBC			= BIT(23) | BIT(24),
341 342
};

Johannes Berg's avatar
Johannes Berg committed
343 344
#define IEEE80211_TX_CTL_STBC_SHIFT		23

345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364
/**
 * enum mac80211_rate_control_flags - per-rate flags set by the
 *	Rate Control algorithm.
 *
 * These flags are set by the Rate control algorithm for each rate during tx,
 * in the @flags member of struct ieee80211_tx_rate.
 *
 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
 *	This is set if the current BSS requires ERP protection.
 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
 * @IEEE80211_TX_RC_MCS: HT rate.
 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
 *	Greenfield mode.
 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
 *	adjacent 20 MHz channels, if the current channel type is
 *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
 */
365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380
enum mac80211_rate_control_flags {
	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),

	/* rate index is an MCS rate number instead of an index */
	IEEE80211_TX_RC_MCS			= BIT(3),
	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
};


/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
381

382 383
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
384

385 386
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES	5
387 388

/**
389
 * struct ieee80211_tx_rate - rate selection/status
390
 *
391 392
 * @idx: rate index to attempt to send with
 * @flags: rate control flags (&enum mac80211_rate_control_flags)
393
 * @count: number of tries in this rate before going to the next rate
394 395 396 397 398 399
 *
 * A value of -1 for @idx indicates an invalid rate and, if used
 * in an array of retry rates, that no more rates should be tried.
 *
 * When used for transmit status reporting, the driver should
 * always report the rate along with the flags it used.
400 401 402 403 404 405 406 407 408 409 410 411 412 413 414
 *
 * &struct ieee80211_tx_info contains an array of these structs
 * in the control information, and it will be filled by the rate
 * control algorithm according to what should be sent. For example,
 * if this array contains, in the format { <idx>, <count> } the
 * information
 *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
 * then this means that the frame should be transmitted
 * up to twice at rate 3, up to twice at rate 2, and up to four
 * times at rate 1 if it doesn't get acknowledged. Say it gets
 * acknowledged by the peer after the fifth attempt, the status
 * information should then contain
 *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
 * since it was transmitted twice at rate 3, twice at rate 2
 * and once at rate 1 after which we received an acknowledgement.
415
 */
416 417 418 419
struct ieee80211_tx_rate {
	s8 idx;
	u8 count;
	u8 flags;
420
} __attribute__((packed));
421

422 423 424 425 426 427 428 429
/**
 * struct ieee80211_tx_info - skb transmit information
 *
 * This structure is placed in skb->cb for three uses:
 *  (1) mac80211 TX control - mac80211 tells the driver what to do
 *  (2) driver internal use (if applicable)
 *  (3) TX status information - driver tells mac80211 what happened
 *
430 431 432
 * The TX control's sta pointer is only valid during the ->tx call,
 * it may be NULL.
 *
433
 * @flags: transmit info flags, defined above
434
 * @band: the band to transmit on (use for checking for races)
435
 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
436
 * @pad: padding, ignore
437 438 439
 * @control: union for control data
 * @status: union for status data
 * @driver_data: array of driver_data pointers
440
 * @ampdu_ack_len: number of acked aggregated frames.
441
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
442
 * @ampdu_len: number of aggregated frames.
443
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
444
 * @ack_signal: signal strength of the ACK frame
445
 */
446 447 448 449
struct ieee80211_tx_info {
	/* common information */
	u32 flags;
	u8 band;
450

451
	u8 antenna_sel_tx;
452

453
	/* 2 byte hole */
454
	u8 pad[2];
455 456 457

	union {
		struct {
458 459 460 461 462 463 464 465 466 467
			union {
				/* rate control */
				struct {
					struct ieee80211_tx_rate rates[
						IEEE80211_TX_MAX_RATES];
					s8 rts_cts_rate_idx;
				};
				/* only needed before rate control */
				unsigned long jiffies;
			};
468
			/* NB: vif can be NULL for injected frames */
469 470
			struct ieee80211_vif *vif;
			struct ieee80211_key_conf *hw_key;
471
			struct ieee80211_sta *sta;
472 473
		} control;
		struct {
474 475
			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
			u8 ampdu_ack_len;
476
			int ack_signal;
477
			u8 ampdu_len;
478
			/* 15 bytes free */
479
		} status;
480 481 482 483 484 485 486 487
		struct {
			struct ieee80211_tx_rate driver_rates[
				IEEE80211_TX_MAX_RATES];
			void *rate_driver_data[
				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
		};
		void *driver_data[
			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
488
	};
489 490
};

491 492 493 494
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
	return (struct ieee80211_tx_info *)skb->cb;
}
495

496 497 498 499 500
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
	return (struct ieee80211_rx_status *)skb->cb;
}

501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535
/**
 * ieee80211_tx_info_clear_status - clear TX status
 *
 * @info: The &struct ieee80211_tx_info to be cleared.
 *
 * When the driver passes an skb back to mac80211, it must report
 * a number of things in TX status. This function clears everything
 * in the TX status but the rate control information (it does clear
 * the count since you need to fill that in anyway).
 *
 * NOTE: You can only use this function if you do NOT use
 *	 info->driver_data! Use info->rate_driver_data
 *	 instead if you need only the less space that allows.
 */
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
	int i;

	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, control.rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, driver_rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
	/* clear the rate counts */
	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
		info->status.rates[i].count = 0;

	BUILD_BUG_ON(
	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
	memset(&info->status.ampdu_ack_len, 0,
	       sizeof(struct ieee80211_tx_info) -
	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}

536 537 538 539 540 541 542 543 544 545 546 547 548

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
549 550 551 552
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
553
 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
Bruno Randolf's avatar
Bruno Randolf committed
554 555
 *	is valid. This is useful in monitor mode and necessary for beacon frames
 *	to enable IBSS merging.
556
 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
557 558 559
 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
 * @RX_FLAG_SHORT_GI: Short guard interval was used
560 561 562
 * @RX_FLAG_INTERNAL_CMTR: set internally after frame was reported
 *	on cooked monitor to avoid double-reporting it for multiple
 *	virtual interfaces
563 564 565 566 567 568
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
569 570
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
571
	RX_FLAG_TSFT		= 1<<7,
572 573 574 575
	RX_FLAG_SHORTPRE	= 1<<8,
	RX_FLAG_HT		= 1<<9,
	RX_FLAG_40MHZ		= 1<<10,
	RX_FLAG_SHORT_GI	= 1<<11,
576
	RX_FLAG_INTERNAL_CMTR	= 1<<12,
577 578 579 580 581 582 583
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
584
 * frame, in the skb's control buffer (cb).
585
 *
586 587
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
588
 * @band: the active band when this frame was received
589
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
590 591 592
 * @signal: signal strength when receiving this frame, either in dBm, in dB or
 *	unspecified depending on the hardware capabilities flags
 *	@IEEE80211_HW_SIGNAL_*
593
 * @antenna: antenna used
594 595
 * @rate_idx: index of data rate into band's supported rates or MCS index if
 *	HT rates are use (RX_FLAG_HT)
596 597
 * @flag: %RX_FLAG_*
 */
598 599
struct ieee80211_rx_status {
	u64 mactime;
600
	enum ieee80211_band band;
601 602
	int freq;
	int signal;
603
	int antenna;
604
	int rate_idx;
605 606 607
	int flag;
};

608 609 610 611 612
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
613 614 615
 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
 *	to determine for example whether to calculate timestamps for packets
 *	or not, do not use instead of filter flags!
616 617 618 619 620 621 622
 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
 *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
 *	meaning that the hardware still wakes up for beacons, is able to
 *	transmit frames and receive the possible acknowledgment frames.
 *	Not to be confused with hardware specific wakeup/sleep states,
 *	driver is responsible for that. See the section "Powersave support"
 *	for more.
623 624 625 626 627
 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
 *	the driver should be prepared to handle configuration requests but
 *	may turn the device off as much as possible. Typically, this flag will
 *	be set when an interface is set UP but not associated or scanning, but
 *	it can also be unset in that case when monitor interfaces are active.
628 629
 */
enum ieee80211_conf_flags {
630
	IEEE80211_CONF_MONITOR		= (1<<0),
Johannes Berg's avatar
Johannes Berg committed
631
	IEEE80211_CONF_PS		= (1<<1),
632
	IEEE80211_CONF_IDLE		= (1<<2),
633
};
634

635

636 637 638 639
/**
 * enum ieee80211_conf_changed - denotes which configuration changed
 *
 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
640
 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
641
 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
642
 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
643
 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
644
 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
645
 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
646
 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
647 648
 */
enum ieee80211_conf_changed {
649
	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
650
	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
651
	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
652
	IEEE80211_CONF_CHANGE_PS		= BIT(4),
653 654 655
	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
656
	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
657 658
};

659 660 661
/**
 * enum ieee80211_smps_mode - spatial multiplexing power save mode
 *
662 663 664 665 666
 * @IEEE80211_SMPS_AUTOMATIC: automatic
 * @IEEE80211_SMPS_OFF: off
 * @IEEE80211_SMPS_STATIC: static
 * @IEEE80211_SMPS_DYNAMIC: dynamic
 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
667 668 669 670 671 672 673 674 675 676 677
 */
enum ieee80211_smps_mode {
	IEEE80211_SMPS_AUTOMATIC,
	IEEE80211_SMPS_OFF,
	IEEE80211_SMPS_STATIC,
	IEEE80211_SMPS_DYNAMIC,

	/* keep last */
	IEEE80211_SMPS_NUM_MODES,
};

678 679 680 681 682
/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
683 684
 * @flags: configuration flags defined above
 *
685
 * @listen_interval: listen interval in units of beacon interval
686
 * @max_sleep_period: the maximum number of beacon intervals to sleep for
687 688 689 690
 *	before checking the beacon for a TIM bit (managed mode only); this
 *	value will be only achievable between DTIM frames, the hardware
 *	needs to check for the multicast traffic bit in DTIM beacons.
 *	This variable is valid only when the CONF_PS flag is set.
691 692 693
 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
 *	in power saving. Power saving will not be enabled until a beacon
 *	has been received and the DTIM period is known.
694 695 696 697
 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
 *	powersave documentation below. This variable is valid only when
 *	the CONF_PS flag is set.
 *
698
 * @power_level: requested transmit power (in dBm)
699
 *
700
 * @channel: the channel to tune to
701
 * @channel_type: the channel (HT) type
702
 *
703 704 705 706 707 708
 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
 *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
 *    but actually means the number of transmissions not the number of retries
 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
 *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
 *    number of transmissions not the number of retries
709 710 711 712
 *
 * @smps_mode: spatial multiplexing powersave mode; note that
 *	%IEEE80211_SMPS_STATIC is used when the device is not
 *	configured for an HT channel
713 714
 */
struct ieee80211_conf {
715
	u32 flags;
716
	int power_level, dynamic_ps_timeout;
717
	int max_sleep_period;
718

719
	u16 listen_interval;
720
	u8 ps_dtim_period;
721

722 723
	u8 long_frame_max_tx_count, short_frame_max_tx_count;

724
	struct ieee80211_channel *channel;
725
	enum nl80211_channel_type channel_type;
726
	enum ieee80211_smps_mode smps_mode;
727 728
};

729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750
/**
 * struct ieee80211_channel_switch - holds the channel switch data
 *
 * The information provided in this structure is required for channel switch
 * operation.
 *
 * @timestamp: value in microseconds of the 64-bit Time Synchronization
 *	Function (TSF) timer when the frame containing the channel switch
 *	announcement was received. This is simply the rx.mactime parameter
 *	the driver passed into mac80211.
 * @block_tx: Indicates whether transmission must be blocked before the
 *	scheduled channel switch, as indicated by the AP.
 * @channel: the new channel to switch to
 * @count: the number of TBTT's until the channel switch event
 */
struct ieee80211_channel_switch {
	u64 timestamp;
	bool block_tx;
	struct ieee80211_channel *channel;
	u8 count;
};

751 752 753 754 755 756
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
757
 * @type: type of this virtual interface
758 759
 * @bss_conf: BSS configuration for this interface, either our own
 *	or the BSS we're associated to
760
 * @addr: address of this interface
761 762 763 764
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
765
	enum nl80211_iftype type;
766
	struct ieee80211_bss_conf bss_conf;
767
	u8 addr[ETH_ALEN];
768 769 770 771
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

Johannes Berg's avatar
Johannes Berg committed
772 773 774
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
775
	return vif->type == NL80211_IFTYPE_MESH_POINT;
Johannes Berg's avatar
Johannes Berg committed
776 777 778 779
#endif
	return false;
}

780 781 782 783 784
/**
 * enum ieee80211_key_alg - key algorithm
 * @ALG_WEP: WEP40 or WEP104
 * @ALG_TKIP: TKIP
 * @ALG_CCMP: CCMP (AES)
785
 * @ALG_AES_CMAC: AES-128-CMAC
786
 */
787
enum ieee80211_key_alg {
788 789 790
	ALG_WEP,
	ALG_TKIP,
	ALG_CCMP,
791
	ALG_AES_CMAC,
792
};
793

794 795 796 797 798 799 800 801 802 803 804 805 806 807
/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
808 809
 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
 *	that the key is pairwise rather then a shared key.
810 811 812
 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
 *	CCMP key if it requires CCMP encryption of management frames (MFP) to
 *	be done in software.
813
 */
814 815 816 817
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
818
	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
819
	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
820
};
821

822 823 824 825 826 827 828 829
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
830
 *	encrypted in hardware.
831 832 833 834
 * @alg: The key algorithm.
 * @flags: key flags, see &enum ieee80211_key_flags.
 * @keyidx: the key index (0-3)
 * @keylen: key material length
835 836 837 838 839
 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
 * 	data block:
 * 	- Temporal Encryption Key (128 bits)
 * 	- Temporal Authenticator Tx MIC Key (64 bits)
 * 	- Temporal Authenticator Rx MIC Key (64 bits)
840 841
 * @icv_len: The ICV length for this key type
 * @iv_len: The IV length for this key type
842
 */
843
struct ieee80211_key_conf {
844
	enum ieee80211_key_alg alg;
845 846
	u8 icv_len;
	u8 iv_len;
847
	u8 hw_key_idx;
848 849 850
	u8 flags;
	s8 keyidx;
	u8 keylen;
851 852 853
	u8 key[0];
};

854 855 856 857 858 859 860 861 862
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
863
enum set_key_cmd {
864
	SET_KEY, DISABLE_KEY,
865
};
866

867 868 869 870 871 872 873 874
/**
 * struct ieee80211_sta - station table entry
 *
 * A station table entry represents a station we are possibly
 * communicating with. Since stations are RCU-managed in
 * mac80211, any ieee80211_sta pointer you get access to must
 * either be protected by rcu_read_lock() explicitly or implicitly,
 * or you must take good care to not use such a pointer after a
875
 * call to your sta_remove callback that removed it.
876 877 878
 *
 * @addr: MAC address
 * @aid: AID we assigned to the station if we're an AP
879
 * @supp_rates: Bitmap of supported rates (per band)
Johannes Berg's avatar
Johannes Berg committed
880
 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
881 882 883 884
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *), size is determined in hw information.
 */
struct ieee80211_sta {
885
	u32 supp_rates[IEEE80211_NUM_BANDS];
886 887
	u8 addr[ETH_ALEN];
	u16 aid;
888
	struct ieee80211_sta_ht_cap ht_cap;
889 890 891 892 893

	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

894 895 896 897
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
898
 * indicates if an associated station made a power state transition.
899
 *
900 901 902
 * @STA_NOTIFY_SLEEP: a station is now sleeping
 * @STA_NOTIFY_AWAKE: a sleeping station woke up
 */
903
enum sta_notify_cmd {
904 905 906
	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};

907 908 909 910 911 912 913 914 915 916 917 918 919 920 921
/**
 * enum ieee80211_tkip_key_type - get tkip key
 *
 * Used by drivers which need to get a tkip key for skb. Some drivers need a
 * phase 1 key, others need a phase 2 key. A single function allows the driver
 * to get the key, this enum indicates what type of key is required.
 *
 * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
 * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
 */
enum ieee80211_tkip_key_type {
	IEEE80211_TKIP_P1_KEY,
	IEEE80211_TKIP_P2_KEY,
};

922 923 924 925 926 927 928 929 930
/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
931 932 933 934 935 936 937 938 939 940 941 942 943
 * @IEEE80211_HW_HAS_RATE_CONTROL:
 *	The hardware or firmware includes rate control, and cannot be
 *	controlled by the stack. As such, no rate control algorithm
 *	should be instantiated, and the TX rate reported to userspace
 *	will be taken from the TX status instead of the rate control
 *	algorithm.
 *	Note that this requires that the driver implement a number of
 *	callbacks so it has the correct information, it needs to have
 *	the @set_rts_threshold callback and must look at the BSS config
 *	@use_cts_prot for G/N protection, @use_short_slot for slot
 *	timing in 2.4 GHz and @use_short_preamble for preambles for
 *	CCK frames.
 *
944 945 946 947 948 949 950 951 952 953
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
954
 *	the driver can fetch them with ieee80211_get_buffered_bc().
955
 *
956 957 958 959 960 961
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
962 963 964 965 966 967 968 969 970 971 972
 *
 * @IEEE80211_HW_SIGNAL_UNSPEC:
 *	Hardware can provide signal values but we don't know its units. We
 *	expect values between 0 and @max_signal.
 *	If possible please provide dB or dBm instead.
 *
 * @IEEE80211_HW_SIGNAL_DBM:
 *	Hardware gives signal values in dBm, decibel difference from
 *	one milliwatt. This is the preferred method since it is standardized
 *	between different devices. @max_signal does not need to be set.
 *
973 974 975
 * @IEEE80211_HW_SPECTRUM_MGMT:
 * 	Hardware supports spectrum management defined in 802.11h
 * 	Measurement, Channel Switch, Quieting, TPC
Sujith's avatar
Sujith committed
976 977 978
 *
 * @IEEE80211_HW_AMPDU_AGGREGATION:
 *	Hardware supports 11n A-MPDU aggregation.
979
 *
980 981 982 983 984 985 986 987 988
 * @IEEE80211_HW_SUPPORTS_PS:
 *	Hardware has power save support (i.e. can go to sleep).
 *
 * @IEEE80211_HW_PS_NULLFUNC_STACK:
 *	Hardware requires nullfunc frame handling in stack, implies
 *	stack support for dynamic PS.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
 *	Hardware has support for dynamic PS.
989 990 991
 *
 * @IEEE80211_HW_MFP_CAPABLE:
 *	Hardware supports management frame protection (MFP, IEEE 802.11w).
992 993 994 995
 *
 * @IEEE80211_HW_BEACON_FILTER:
 *	Hardware supports dropping of irrelevant beacon frames to
 *	avoid waking up cpu.
996 997 998 999 1000 1001 1002 1003 1004 1005
 *
 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
 *	Hardware supports static spatial multiplexing powersave,
 *	ie. can turn off all but one chain even on HT connections
 *	that should be using more chains.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
 *	Hardware supports dynamic spatial multiplexing powersave,
 *	ie. can turn off all but one chain and then wake the rest
 *	up as required after, for example, rts/cts handshake.
1006 1007 1008 1009 1010
 *
 * @IEEE80211_HW_SUPPORTS_UAPSD:
 *	Hardware supports Unscheduled Automatic Power Save Delivery
 *	(U-APSD) in managed mode. The mode is configured with
 *	conf_tx() operation.
1011 1012 1013 1014 1015
 *
 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
 *	Hardware can provide ack status reports of Tx frames to
 *	the stack.
 *
1016 1017 1018 1019 1020
 * @IEEE80211_HW_CONNECTION_MONITOR:
 *      The hardware performs its own connection monitoring, including
 *      periodic keep-alives to the AP and probing the AP on beacon loss.
 *      When this flag is set, signaling beacon-loss will cause an immediate
 *      change to disassociated state.
1021 1022 1023 1024 1025 1026
 *
 * @IEEE80211_HW_SUPPORTS_CQM_RSSI:
 *	Hardware can do connection quality monitoring - i.e. it can monitor
 *	connection quality related parameters, such as the RSSI level and
 *	provide notifications if configured trigger levels are reached.
 *
1027 1028
 */
enum ieee80211_hw_flags {
1029
	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
1030 1031
	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
1032 1033
	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
1034
	IEEE80211_HW_SIGNAL_UNSPEC			= 1<<5,
Johannes Berg's avatar
Johannes Berg committed
1035
	IEEE80211_HW_SIGNAL_DBM				= 1<<6,
1036
	/* use this hole */
Johannes Berg's avatar
Johannes Berg committed
1037 1038 1039 1040 1041 1042
	IEEE80211_HW_SPECTRUM_MGMT			= 1<<8,
	IEEE80211_HW_AMPDU_AGGREGATION			= 1<<9,
	IEEE80211_HW_SUPPORTS_PS			= 1<<10,
	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
1043
	IEEE80211_HW_BEACON_FILTER			= 1<<14,
1044 1045
	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
1046
	IEEE80211_HW_SUPPORTS_UAPSD			= 1<<17,
1047
	IEEE80211_HW_REPORTS_TX_ACK_STATUS		= 1<<18,
1048
	IEEE80211_HW_CONNECTION_MONITOR			= 1<<19,
1049
	IEEE80211_HW_SUPPORTS_CQM_RSSI			= 1<<20,
1050 1051
};

1052 1053
/**
 * struct ieee80211_hw - hardware information and state
Johannes Berg's avatar