mac80211.h 80.8 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
Johannes Berg's avatar
Johannes Berg committed
6
 * Copyright 2007-2008	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/cfg80211.h>

24 25 26 27 28 29 30 31 32 33 34 35 36
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 38 39
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
40 41 42 43
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44
 *	 use the non-IRQ-safe functions!
45 46
 */

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
73 74
 */

Johannes Berg's avatar
Johannes Berg committed
75 76 77 78 79 80
/**
 * enum ieee80211_max_queues - maximum number of queues
 *
 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
 */
enum ieee80211_max_queues {
81
	IEEE80211_MAX_QUEUES =		4,
Johannes Berg's avatar
Johannes Berg committed
82 83
};

84 85 86 87
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
88
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
89
 *
90
 * @aifs: arbitration interframe space [0..255]
91 92
 * @cw_min: minimum contention window [a value of the form
 *	2^n-1 in the range 1..32767]
93
 * @cw_max: maximum contention window [like @cw_min]
94
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
95
 */
96
struct ieee80211_tx_queue_params {
97
	u16 txop;
98 99
	u16 cw_min;
	u16 cw_max;
100
	u8 aifs;
101 102
};

103
/**
104
 * struct ieee80211_tx_queue_stats - transmit queue statistics
105 106 107 108 109
 *
 * @len: number of packets in queue
 * @limit: queue length limit
 * @count: number of frames sent
 */
110
struct ieee80211_tx_queue_stats {
111 112 113
	unsigned int len;
	unsigned int limit;
	unsigned int count;
114 115 116 117 118 119 120 121 122
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

123 124 125 126 127 128 129 130 131 132
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
133
 * @BSS_CHANGED_ERP_SLOT: slot timing changed
Tomas Winkler's avatar
Tomas Winkler committed
134
 * @BSS_CHANGED_HT: 802.11n parameters changed
135
 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
136
 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
137 138 139 140 141 142
 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
 *	reason (IBSS and managed mode)
 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
 *	new beacon (beaconing modes)
 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
 *	enabled/disabled (beaconing modes)
143 144 145 146 147
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
148
	BSS_CHANGED_ERP_SLOT		= 1<<3,
Tomas Winkler's avatar
Tomas Winkler committed
149
	BSS_CHANGED_HT                  = 1<<4,
150
	BSS_CHANGED_BASIC_RATES		= 1<<5,
151
	BSS_CHANGED_BEACON_INT		= 1<<6,
152 153 154
	BSS_CHANGED_BSSID		= 1<<7,
	BSS_CHANGED_BEACON		= 1<<8,
	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
155 156 157 158 159 160 161 162 163 164 165
};

/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
166 167 168 169 170 171
 * @use_short_preamble: use 802.11b short preamble;
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
 * @use_short_slot: use short slot time (only relevant for ERP);
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
172
 * @dtim_period: num of beacons before the next DTIM, for PSM
173 174
 * @timestamp: beacon timestamp
 * @beacon_int: beacon interval
175
 * @assoc_capability: capabilities taken from assoc resp
176 177 178
 * @basic_rates: bitmap of basic rates, each bit stands for an
 *	index into the rate table configured by the driver in
 *	the current band.
179 180
 * @bssid: The BSSID for this BSS
 * @enable_beacon: whether beaconing should be enabled or not
181 182
 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
 *	This field is only valid when the channel type is one of the HT types.
183 184
 */
struct ieee80211_bss_conf {
185
	const u8 *bssid;
186 187 188 189 190 191
	/* association related data */
	bool assoc;
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
192
	bool use_short_slot;
193
	bool enable_beacon;
194
	u8 dtim_period;
195 196 197
	u16 beacon_int;
	u16 assoc_capability;
	u64 timestamp;
198
	u32 basic_rates;
199
	u16 ht_operation_mode;
200 201
};

202
/**
203
 * enum mac80211_tx_control_flags - flags to describe transmission information/status
204
 *
205
 * These flags are used with the @flags member of &ieee80211_tx_info.
206 207
 *
 * @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
208 209 210 211 212 213 214 215 216 217 218
 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
 *	number to this frame, taking care of not overwriting the fragment
 *	number and increasing the sequence number only when the
 *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
 *	assign sequence numbers to QoS-data frames but cannot do so correctly
 *	for non-QoS-data and management frames because beacons need them from
 *	that counter as well and mac80211 cannot guarantee proper sequencing.
 *	If this flag is set, the driver should instruct the hardware to
 *	assign a sequence number to the frame or assign one itself. Cf. IEEE
 *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
 *	beacons and always be clear for frames without a sequence number field.
219 220 221 222 223 224
 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
 *	station
 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
225
 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
226 227 228 229 230
 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
 *	because the destination STA was in powersave mode.
 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
231 232
 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
 * 	so consider using block ack request (BAR).
233 234 235
 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
 *	set by rate control algorithms to indicate probe rate, will
 *	be cleared for fragmented frames (except on the last fragment)
236 237 238
 * @IEEE80211_TX_INTFL_RCALGO: mac80211 internal flag, do not test or
 *	set this flag in the driver; indicates that the rate control
 *	algorithm was used and should be notified of TX status
239 240 241
 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
 *	used to indicate that a pending frame requires TX processing before
 *	it can be sent out.
242 243
 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
 *	used to indicate that a frame was already retried due to PS
Johannes Berg's avatar
Johannes Berg committed
244 245
 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
 *	used to indicate frame should not be encrypted
246 247 248
 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
 *	This frame is a response to a PS-poll frame and should be sent
 *	although the station is in powersave mode.
249 250
 */
enum mac80211_tx_control_flags {
251
	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
252 253 254 255 256 257 258 259 260 261 262 263
	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
	IEEE80211_TX_CTL_AMPDU			= BIT(6),
	IEEE80211_TX_CTL_INJECTED		= BIT(7),
	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
	IEEE80211_TX_STAT_ACK			= BIT(9),
	IEEE80211_TX_STAT_AMPDU			= BIT(10),
	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
264
	IEEE80211_TX_INTFL_RCALGO		= BIT(13),
265
	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
266
	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
Johannes Berg's avatar
Johannes Berg committed
267
	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
268
	IEEE80211_TX_CTL_PSPOLL_RESPONSE	= BIT(17),
269 270
};

271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290
/**
 * enum mac80211_rate_control_flags - per-rate flags set by the
 *	Rate Control algorithm.
 *
 * These flags are set by the Rate control algorithm for each rate during tx,
 * in the @flags member of struct ieee80211_tx_rate.
 *
 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
 *	This is set if the current BSS requires ERP protection.
 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
 * @IEEE80211_TX_RC_MCS: HT rate.
 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
 *	Greenfield mode.
 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
 *	adjacent 20 MHz channels, if the current channel type is
 *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
 */
291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306
enum mac80211_rate_control_flags {
	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),

	/* rate index is an MCS rate number instead of an index */
	IEEE80211_TX_RC_MCS			= BIT(3),
	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
};


/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
307

308 309
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
310

311 312
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES	5
313 314

/**
315
 * struct ieee80211_tx_rate - rate selection/status
316
 *
317 318
 * @idx: rate index to attempt to send with
 * @flags: rate control flags (&enum mac80211_rate_control_flags)
319
 * @count: number of tries in this rate before going to the next rate
320 321 322 323 324 325
 *
 * A value of -1 for @idx indicates an invalid rate and, if used
 * in an array of retry rates, that no more rates should be tried.
 *
 * When used for transmit status reporting, the driver should
 * always report the rate along with the flags it used.
326
 */
327 328 329 330
struct ieee80211_tx_rate {
	s8 idx;
	u8 count;
	u8 flags;
331
} __attribute__((packed));
332

333 334 335 336 337 338 339 340
/**
 * struct ieee80211_tx_info - skb transmit information
 *
 * This structure is placed in skb->cb for three uses:
 *  (1) mac80211 TX control - mac80211 tells the driver what to do
 *  (2) driver internal use (if applicable)
 *  (3) TX status information - driver tells mac80211 what happened
 *
341 342 343
 * The TX control's sta pointer is only valid during the ->tx call,
 * it may be NULL.
 *
344
 * @flags: transmit info flags, defined above
345
 * @band: the band to transmit on (use for checking for races)
346
 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
347
 * @pad: padding, ignore
348 349 350
 * @control: union for control data
 * @status: union for status data
 * @driver_data: array of driver_data pointers
351 352 353 354 355
 * @ampdu_ack_len: number of aggregated frames.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
 * @ampdu_ack_map: block ack bit map for the aggregation.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
 * @ack_signal: signal strength of the ACK frame
356
 */
357 358 359 360
struct ieee80211_tx_info {
	/* common information */
	u32 flags;
	u8 band;
361

362
	u8 antenna_sel_tx;
363

364
	/* 2 byte hole */
365
	u8 pad[2];
366 367 368

	union {
		struct {
369 370 371 372 373 374 375 376 377 378
			union {
				/* rate control */
				struct {
					struct ieee80211_tx_rate rates[
						IEEE80211_TX_MAX_RATES];
					s8 rts_cts_rate_idx;
				};
				/* only needed before rate control */
				unsigned long jiffies;
			};
379
			/* NB: vif can be NULL for injected frames */
380 381
			struct ieee80211_vif *vif;
			struct ieee80211_key_conf *hw_key;
382
			struct ieee80211_sta *sta;
383 384
		} control;
		struct {
385 386
			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
			u8 ampdu_ack_len;
387 388
			u64 ampdu_ack_map;
			int ack_signal;
389
			/* 8 bytes free */
390
		} status;
391 392 393 394 395 396 397 398
		struct {
			struct ieee80211_tx_rate driver_rates[
				IEEE80211_TX_MAX_RATES];
			void *rate_driver_data[
				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
		};
		void *driver_data[
			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
399
	};
400 401
};

402 403 404 405
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
	return (struct ieee80211_tx_info *)skb->cb;
}
406

407 408 409 410 411
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
	return (struct ieee80211_rx_status *)skb->cb;
}

412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446
/**
 * ieee80211_tx_info_clear_status - clear TX status
 *
 * @info: The &struct ieee80211_tx_info to be cleared.
 *
 * When the driver passes an skb back to mac80211, it must report
 * a number of things in TX status. This function clears everything
 * in the TX status but the rate control information (it does clear
 * the count since you need to fill that in anyway).
 *
 * NOTE: You can only use this function if you do NOT use
 *	 info->driver_data! Use info->rate_driver_data
 *	 instead if you need only the less space that allows.
 */
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
	int i;

	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, control.rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, driver_rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
	/* clear the rate counts */
	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
		info->status.rates[i].count = 0;

	BUILD_BUG_ON(
	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
	memset(&info->status.ampdu_ack_len, 0,
	       sizeof(struct ieee80211_tx_info) -
	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}

447 448 449 450 451 452 453 454 455 456 457 458 459 460

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
461 462 463 464
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
465
 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
Bruno Randolf's avatar
Bruno Randolf committed
466 467
 *	is valid. This is useful in monitor mode and necessary for beacon frames
 *	to enable IBSS merging.
468
 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
469 470 471
 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
 * @RX_FLAG_SHORT_GI: Short guard interval was used
472 473 474 475 476 477 478
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_RADIOTAP	= 1<<2,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
479 480
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
481
	RX_FLAG_TSFT		= 1<<7,
482 483 484 485
	RX_FLAG_SHORTPRE	= 1<<8,
	RX_FLAG_HT		= 1<<9,
	RX_FLAG_40MHZ		= 1<<10,
	RX_FLAG_SHORT_GI	= 1<<11,
486 487 488 489 490 491 492
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
493
 * frame, in the skb's control buffer (cb).
494
 *
495 496
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
497
 * @band: the active band when this frame was received
498
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
499 500 501 502 503
 * @signal: signal strength when receiving this frame, either in dBm, in dB or
 *	unspecified depending on the hardware capabilities flags
 *	@IEEE80211_HW_SIGNAL_*
 * @noise: noise when receiving this frame, in dBm.
 * @qual: overall signal quality indication, in percent (0-100).
504
 * @antenna: antenna used
505 506
 * @rate_idx: index of data rate into band's supported rates or MCS index if
 *	HT rates are use (RX_FLAG_HT)
507 508
 * @flag: %RX_FLAG_*
 */
509 510
struct ieee80211_rx_status {
	u64 mactime;
511
	enum ieee80211_band band;
512 513
	int freq;
	int signal;
514
	int noise;
515
	int qual;
516
	int antenna;
517
	int rate_idx;
518 519 520
	int flag;
};

521 522 523 524 525 526
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
 * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
527
 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only)
528 529 530 531 532
 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
 *	the driver should be prepared to handle configuration requests but
 *	may turn the device off as much as possible. Typically, this flag will
 *	be set when an interface is set UP but not associated or scanning, but
 *	it can also be unset in that case when monitor interfaces are active.
533 534
 */
enum ieee80211_conf_flags {
535
	IEEE80211_CONF_RADIOTAP		= (1<<0),
Johannes Berg's avatar
Johannes Berg committed
536
	IEEE80211_CONF_PS		= (1<<1),
537
	IEEE80211_CONF_IDLE		= (1<<2),
538
};
539

540

541 542 543
/**
 * enum ieee80211_conf_changed - denotes which configuration changed
 *
Johannes Berg's avatar
Johannes Berg committed
544
 * @_IEEE80211_CONF_CHANGE_RADIO_ENABLED: DEPRECATED
545 546
 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
 * @IEEE80211_CONF_CHANGE_RADIOTAP: the radiotap flag changed
547
 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
548
 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
549
 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
550
 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
551
 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
552 553
 */
enum ieee80211_conf_changed {
Johannes Berg's avatar
Johannes Berg committed
554
	_IEEE80211_CONF_CHANGE_RADIO_ENABLED	= BIT(0),
555 556 557
	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
	IEEE80211_CONF_CHANGE_RADIOTAP		= BIT(3),
	IEEE80211_CONF_CHANGE_PS		= BIT(4),
558 559 560
	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
561
	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
562 563
};

Johannes Berg's avatar
Johannes Berg committed
564 565 566 567 568 569 570 571
static inline __deprecated enum ieee80211_conf_changed
__IEEE80211_CONF_CHANGE_RADIO_ENABLED(void)
{
	return _IEEE80211_CONF_CHANGE_RADIO_ENABLED;
}
#define IEEE80211_CONF_CHANGE_RADIO_ENABLED \
	__IEEE80211_CONF_CHANGE_RADIO_ENABLED()

572 573 574 575 576
/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
577 578
 * @flags: configuration flags defined above
 *
579
 * @radio_enabled: when zero, driver is required to switch off the radio.
580
 * @beacon_int: DEPRECATED, DO NOT USE
581
 *
582
 * @listen_interval: listen interval in units of beacon interval
583
 * @max_sleep_period: the maximum number of beacon intervals to sleep for
584 585 586 587 588 589 590 591
 *	before checking the beacon for a TIM bit (managed mode only); this
 *	value will be only achievable between DTIM frames, the hardware
 *	needs to check for the multicast traffic bit in DTIM beacons.
 *	This variable is valid only when the CONF_PS flag is set.
 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
 *	powersave documentation below. This variable is valid only when
 *	the CONF_PS flag is set.
 *
592
 * @power_level: requested transmit power (in dBm)
593
 *
594
 * @channel: the channel to tune to
595
 * @channel_type: the channel (HT) type
596
 *
597 598 599 600 601 602
 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
 *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
 *    but actually means the number of transmissions not the number of retries
 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
 *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
 *    number of transmissions not the number of retries
603 604
 */
struct ieee80211_conf {
605
	int __deprecated beacon_int;
606
	u32 flags;
607
	int power_level, dynamic_ps_timeout;
608
	int max_sleep_period;
609

610
	u16 listen_interval;
Johannes Berg's avatar
Johannes Berg committed
611
	bool __deprecated radio_enabled;
612

613 614
	u8 long_frame_max_tx_count, short_frame_max_tx_count;

615
	struct ieee80211_channel *channel;
616
	enum nl80211_channel_type channel_type;
617 618
};

619 620 621 622 623 624
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
625
 * @type: type of this virtual interface
626 627
 * @bss_conf: BSS configuration for this interface, either our own
 *	or the BSS we're associated to
628 629 630 631
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
632
	enum nl80211_iftype type;
633
	struct ieee80211_bss_conf bss_conf;
634 635 636 637
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

Johannes Berg's avatar
Johannes Berg committed
638 639 640
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
641
	return vif->type == NL80211_IFTYPE_MESH_POINT;
Johannes Berg's avatar
Johannes Berg committed
642 643 644 645
#endif
	return false;
}

646 647 648
/**
 * struct ieee80211_if_init_conf - initial configuration of an interface
 *
649 650 651
 * @vif: pointer to a driver-use per-interface structure. The pointer
 *	itself is also used for various functions including
 *	ieee80211_beacon_get() and ieee80211_get_buffered_bc().
652
 * @type: one of &enum nl80211_iftype constants. Determines the type of
653 654 655 656 657 658 659
 *	added/removed interface.
 * @mac_addr: pointer to MAC address of the interface. This pointer is valid
 *	until the interface is removed (i.e. it cannot be used after
 *	remove_interface() callback was called for this interface).
 *
 * This structure is used in add_interface() and remove_interface()
 * callbacks of &struct ieee80211_hw.
660 661 662 663 664 665
 *
 * When you allow multiple interfaces to be added to your PHY, take care
 * that the hardware can actually handle multiple MAC addresses. However,
 * also take care that when there's no interface left with mac_addr != %NULL
 * you remove the MAC address from the device to avoid acknowledging packets
 * in pure monitor mode.
666 667
 */
struct ieee80211_if_init_conf {
668
	enum nl80211_iftype type;
669
	struct ieee80211_vif *vif;
670 671 672
	void *mac_addr;
};

673 674 675 676 677
/**
 * enum ieee80211_key_alg - key algorithm
 * @ALG_WEP: WEP40 or WEP104
 * @ALG_TKIP: TKIP
 * @ALG_CCMP: CCMP (AES)
678
 * @ALG_AES_CMAC: AES-128-CMAC
679
 */
680
enum ieee80211_key_alg {
681 682 683
	ALG_WEP,
	ALG_TKIP,
	ALG_CCMP,
684
	ALG_AES_CMAC,
685
};
686

687 688 689 690 691 692 693 694 695 696 697 698 699 700
/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
701 702
 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
 *	that the key is pairwise rather then a shared key.
703 704 705
 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
 *	CCMP key if it requires CCMP encryption of management frames (MFP) to
 *	be done in software.
706
 */
707 708 709 710
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
711
	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
712
	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
713
};
714

715 716 717 718 719 720 721 722
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
723
 *	encrypted in hardware.
724 725 726 727
 * @alg: The key algorithm.
 * @flags: key flags, see &enum ieee80211_key_flags.
 * @keyidx: the key index (0-3)
 * @keylen: key material length
728 729 730 731 732
 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
 * 	data block:
 * 	- Temporal Encryption Key (128 bits)
 * 	- Temporal Authenticator Tx MIC Key (64 bits)
 * 	- Temporal Authenticator Rx MIC Key (64 bits)
733 734
 * @icv_len: The ICV length for this key type
 * @iv_len: The IV length for this key type
735
 */
736
struct ieee80211_key_conf {
737
	enum ieee80211_key_alg alg;
738 739
	u8 icv_len;
	u8 iv_len;
740
	u8 hw_key_idx;
741 742 743
	u8 flags;
	s8 keyidx;
	u8 keylen;
744 745 746
	u8 key[0];
};

747 748 749 750 751 752 753 754 755
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
756
enum set_key_cmd {
757
	SET_KEY, DISABLE_KEY,
758
};
759

760 761 762 763 764 765 766 767 768 769 770 771
/**
 * struct ieee80211_sta - station table entry
 *
 * A station table entry represents a station we are possibly
 * communicating with. Since stations are RCU-managed in
 * mac80211, any ieee80211_sta pointer you get access to must
 * either be protected by rcu_read_lock() explicitly or implicitly,
 * or you must take good care to not use such a pointer after a
 * call to your sta_notify callback that removed it.
 *
 * @addr: MAC address
 * @aid: AID we assigned to the station if we're an AP
772
 * @supp_rates: Bitmap of supported rates (per band)
Johannes Berg's avatar
Johannes Berg committed
773
 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
774 775 776 777
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *), size is determined in hw information.
 */
struct ieee80211_sta {
778
	u32 supp_rates[IEEE80211_NUM_BANDS];
779 780
	u8 addr[ETH_ALEN];
	u16 aid;
781
	struct ieee80211_sta_ht_cap ht_cap;
782 783 784 785 786

	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

787 788 789 790
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
791 792
 * indicates addition and removal of a station to station table,
 * or if a associated station made a power state transition.
793 794 795
 *
 * @STA_NOTIFY_ADD: a station was added to the station table
 * @STA_NOTIFY_REMOVE: a station being removed from the station table
796 797 798
 * @STA_NOTIFY_SLEEP: a station is now sleeping
 * @STA_NOTIFY_AWAKE: a sleeping station woke up
 */
799 800
enum sta_notify_cmd {
	STA_NOTIFY_ADD, STA_NOTIFY_REMOVE,
801 802 803
	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};

804 805 806 807 808 809 810 811 812 813 814 815 816 817 818
/**
 * enum ieee80211_tkip_key_type - get tkip key
 *
 * Used by drivers which need to get a tkip key for skb. Some drivers need a
 * phase 1 key, others need a phase 2 key. A single function allows the driver
 * to get the key, this enum indicates what type of key is required.
 *
 * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
 * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
 */
enum ieee80211_tkip_key_type {
	IEEE80211_TKIP_P1_KEY,
	IEEE80211_TKIP_P2_KEY,
};

819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837
/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
838
 *	the driver can fetch them with ieee80211_get_buffered_bc().
839
 *
840 841 842 843 844 845
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
846 847 848 849 850 851 852 853 854 855 856 857 858 859
 *
 * @IEEE80211_HW_SIGNAL_UNSPEC:
 *	Hardware can provide signal values but we don't know its units. We
 *	expect values between 0 and @max_signal.
 *	If possible please provide dB or dBm instead.
 *
 * @IEEE80211_HW_SIGNAL_DBM:
 *	Hardware gives signal values in dBm, decibel difference from
 *	one milliwatt. This is the preferred method since it is standardized
 *	between different devices. @max_signal does not need to be set.
 *
 * @IEEE80211_HW_NOISE_DBM:
 *	Hardware can provide noise (radio interference) values in units dBm,
 *      decibel difference from one milliwatt.
860 861 862 863
 *
 * @IEEE80211_HW_SPECTRUM_MGMT:
 * 	Hardware supports spectrum management defined in 802.11h
 * 	Measurement, Channel Switch, Quieting, TPC
Sujith's avatar
Sujith committed
864 865 866
 *
 * @IEEE80211_HW_AMPDU_AGGREGATION:
 *	Hardware supports 11n A-MPDU aggregation.
867
 *
868 869 870 871 872 873 874 875 876
 * @IEEE80211_HW_SUPPORTS_PS:
 *	Hardware has power save support (i.e. can go to sleep).
 *
 * @IEEE80211_HW_PS_NULLFUNC_STACK:
 *	Hardware requires nullfunc frame handling in stack, implies
 *	stack support for dynamic PS.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
 *	Hardware has support for dynamic PS.
877 878 879
 *
 * @IEEE80211_HW_MFP_CAPABLE:
 *	Hardware supports management frame protection (MFP, IEEE 802.11w).
880 881 882 883
 *
 * @IEEE80211_HW_BEACON_FILTER:
 *	Hardware supports dropping of irrelevant beacon frames to
 *	avoid waking up cpu.
884 885 886 887
 */
enum ieee80211_hw_flags {
	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
888 889
	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
890
	IEEE80211_HW_SIGNAL_UNSPEC			= 1<<5,
Johannes Berg's avatar
Johannes Berg committed
891 892 893 894 895 896 897 898
	IEEE80211_HW_SIGNAL_DBM				= 1<<6,
	IEEE80211_HW_NOISE_DBM				= 1<<7,
	IEEE80211_HW_SPECTRUM_MGMT			= 1<<8,
	IEEE80211_HW_AMPDU_AGGREGATION			= 1<<9,
	IEEE80211_HW_SUPPORTS_PS			= 1<<10,
	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
899
	IEEE80211_HW_BEACON_FILTER			= 1<<14,
900 901
};

902 903
/**
 * struct ieee80211_hw - hardware information and state
904 905 906 907 908 909 910
 *
 * This structure contains the configuration and hardware
 * information for an 802.11 PHY.
 *
 * @wiphy: This points to the &struct wiphy allocated for this
 *	802.11 PHY. You must fill in the @perm_addr and @dev
 *	members of this structure using SET_IEEE80211_DEV()
911 912
 *	and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
 *	bands (with channels, bitrates) are registered here.
913 914 915 916
 *
 * @conf: &struct ieee80211_conf, device configuration, don't use.
 *
 * @workqueue: single threaded workqueue available for driver use,
917 918
 *	allocated by mac80211 on registration and flushed when an
 *	interface is removed.
919 920
 *	NOTICE: All work performed on this workqueue must not
 *	acquire the RTNL lock.
921 922 923 924 925 926 927 928 929 930 931
 *
 * @priv: pointer to private area that was allocated for driver use
 *	along with this structure.
 *
 * @flags: hardware flags, see &enum ieee80211_hw_flags.
 *
 * @extra_tx_headroom: headroom to reserve in each transmit skb
 *	for use by the driver (e.g. for transmit headers.)
 *
 * @channel_change_time: time (in microseconds) it takes to change channels.
 *
932 933
 * @max_signal: Maximum value for signal (rssi) in RX information, used
 *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
934
 *
935 936 937
 * @max_listen_interval: max listen interval in units of beacon interval
 *     that HW supports
 *
938
 * @queues: number of available hardware transmit queues for
Johannes Berg's avatar
Johannes Berg committed
939 940 941
 *	data packets. WMM/QoS requires at least four, these
 *	queues need to have configurable access parameters.
 *
942 943 944
 * @rate_control_algorithm: rate control algorithm for this hardware.
 *	If unset (NULL), the default algorithm will be used. Must be
 *	set before calling ieee80211_register_hw().
945 946 947
 *
 * @vif_data_size: size (in bytes) of the drv_priv data area
 *	within &struct ieee80211_vif.
948 949
 * @sta_data_size: size (in bytes) of the drv_priv data area
 *	within &struct ieee80211_sta.
950
 *
951 952
 * @max_rates: maximum number of alternate rate retry stages
 * @max_rate_tries: maximum number of tries for each stage
953
 */
954 955
struct ieee80211_hw {
	struct ieee80211_conf conf;
956
	struct wiphy *wiphy;
957
	struct workqueue_struct *workqueue;
958
	const char *rate_control_algorithm;
959
	void *priv;
960
	u32 flags;
961 962
	unsigned int extra_tx_headroom;
	int channel_change_time;
963
	int vif_data_size;
964
	int sta_data_size;
965 966
	u16 queues;
	u16 max_listen_interval;
967
	s8 max_signal;
968 969
	u8 max_rates;
	u8 max_rate_tries;
970 971
};

972 973 974 975 976 977 978 979 980 981 982 983 984
/**
 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
 *
 * @wiphy: the &struct wiphy which we want to query
 *
 * mac80211 drivers can use this to get to their respective
 * &struct ieee80211_hw. Drivers wishing to get to their own private
 * structure can then access it via hw->priv. Note that mac802111 drivers should
 * not use wiphy_priv() to try to get their private driver structure as this
 * is already used internally by mac80211.
 */
struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);

985 986 987 988 989 990
/**
 * SET_IEEE80211_DEV - set device for 802.11 hardware
 *
 * @hw: the &struct ieee80211_hw to set the device for
 * @dev: the &struct device of this 802.11 device
 */
991 992 993 994 995
static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
	set_wiphy_dev(hw->wiphy, dev);
}

996
/**
997
 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
998 999 1000 1001
 *
 * @hw: the &struct ieee80211_hw to set the MAC address for
 * @addr: the address to set
 */
1002 1003 1004 1005 1006
static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
{
	memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}

1007 1008
static inline struct ieee80211_rate *
ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
1009
		      const struct ieee80211_tx_info *c)
1010
{
1011
	if (WARN_ON(c->control.rates[0].idx < 0))
1012
		return NULL;
1013
	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
1014 1015 1016 1017
}

static inline struct ieee80211_rate *
ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
1018
			   const struct ieee80211_tx_info *c)
1019
{
1020
	if (c->control.rts_cts_rate_idx < 0)
1021
		return NULL;
1022
	return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
1023 1024 1025 1026
}

static inline struct ieee80211_rate *
ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
1027
			     const struct ieee80211_tx_info *c, int idx)
1028
{
1029
	if (c->control.rates[idx + 1].idx < 0)
1030
		return NULL;
1031
	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
1032 1033
}

1034 1035 1036 1037 1038 1039 1040 1041
/**
 * DOC: Hardware crypto acceleration
 *
 * mac80211 is capable of taking advantage of many hardware
 * acceleration designs for encryption and decryption operations.
 *
 * The set_key() callback in the &struct ieee80211_ops for a given
 * device is called to enable hardware acceleration of encryption and
1042 1043 1044
 * decryption. The callback takes a @sta parameter that will be NULL
 * for default keys or keys used for transmission only, or point to
 * the station information for the peer for individual keys.