mac80211.h 95 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
Johannes Berg's avatar
Johannes Berg committed
6
 * Copyright 2007-2008	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/cfg80211.h>

24 25 26 27 28 29 30 31 32 33 34 35 36
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 38 39
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
40 41 42 43
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44
 *	 use the non-IRQ-safe functions!
45 46
 */

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
73 74
 */

75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
/**
 * DOC: mac80211 workqueue
 *
 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
 * The workqueue is a single threaded workqueue and can only be accessed by
 * helpers for sanity checking. Drivers must ensure all work added onto the
 * mac80211 workqueue should be cancelled on the driver stop() callback.
 *
 * mac80211 will flushed the workqueue upon interface removal and during
 * suspend.
 *
 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
 *
 */

Johannes Berg's avatar
Johannes Berg committed
90 91 92 93 94 95
/**
 * enum ieee80211_max_queues - maximum number of queues
 *
 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
 */
enum ieee80211_max_queues {
96
	IEEE80211_MAX_QUEUES =		4,
Johannes Berg's avatar
Johannes Berg committed
97 98
};

99 100 101 102
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
103
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
104
 *
105
 * @aifs: arbitration interframe space [0..255]
106 107
 * @cw_min: minimum contention window [a value of the form
 *	2^n-1 in the range 1..32767]
108
 * @cw_max: maximum contention window [like @cw_min]
109
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
110
 * @uapsd: is U-APSD mode enabled for the queue
111
 */
112
struct ieee80211_tx_queue_params {
113
	u16 txop;
114 115
	u16 cw_min;
	u16 cw_max;
116
	u8 aifs;
117
	bool uapsd;
118 119
};

120
/**
121
 * struct ieee80211_tx_queue_stats - transmit queue statistics
122 123 124 125 126
 *
 * @len: number of packets in queue
 * @limit: queue length limit
 * @count: number of frames sent
 */
127
struct ieee80211_tx_queue_stats {
128 129 130
	unsigned int len;
	unsigned int limit;
	unsigned int count;
131 132 133 134 135 136 137 138 139
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

140 141 142 143 144 145 146 147 148 149
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
150
 * @BSS_CHANGED_ERP_SLOT: slot timing changed
Tomas Winkler's avatar
Tomas Winkler committed
151
 * @BSS_CHANGED_HT: 802.11n parameters changed
152
 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
153
 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
154 155 156 157 158 159
 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
 *	reason (IBSS and managed mode)
 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
 *	new beacon (beaconing modes)
 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
 *	enabled/disabled (beaconing modes)
160 161 162 163 164
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
165
	BSS_CHANGED_ERP_SLOT		= 1<<3,
Tomas Winkler's avatar
Tomas Winkler committed
166
	BSS_CHANGED_HT                  = 1<<4,
167
	BSS_CHANGED_BASIC_RATES		= 1<<5,
168
	BSS_CHANGED_BEACON_INT		= 1<<6,
169 170 171
	BSS_CHANGED_BSSID		= 1<<7,
	BSS_CHANGED_BEACON		= 1<<8,
	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
172 173 174 175 176 177 178 179 180 181 182
};

/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
183 184 185 186 187 188
 * @use_short_preamble: use 802.11b short preamble;
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
 * @use_short_slot: use short slot time (only relevant for ERP);
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
189 190
 * @dtim_period: num of beacons before the next DTIM, for beaconing,
 *	not valid in station mode (cf. hw conf ps_dtim_period)
191 192
 * @timestamp: beacon timestamp
 * @beacon_int: beacon interval
193
 * @assoc_capability: capabilities taken from assoc resp
194 195 196
 * @basic_rates: bitmap of basic rates, each bit stands for an
 *	index into the rate table configured by the driver in
 *	the current band.
197 198
 * @bssid: The BSSID for this BSS
 * @enable_beacon: whether beaconing should be enabled or not
199 200
 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
 *	This field is only valid when the channel type is one of the HT types.
201 202
 */
struct ieee80211_bss_conf {
203
	const u8 *bssid;
204 205 206 207 208 209
	/* association related data */
	bool assoc;
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
210
	bool use_short_slot;
211
	bool enable_beacon;
212
	u8 dtim_period;
213 214 215
	u16 beacon_int;
	u16 assoc_capability;
	u64 timestamp;
216
	u32 basic_rates;
217
	u16 ht_operation_mode;
218 219
};

220
/**
221
 * enum mac80211_tx_control_flags - flags to describe transmission information/status
222
 *
223
 * These flags are used with the @flags member of &ieee80211_tx_info.
224
 *
225
 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
226 227 228 229 230 231 232 233 234 235 236
 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
 *	number to this frame, taking care of not overwriting the fragment
 *	number and increasing the sequence number only when the
 *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
 *	assign sequence numbers to QoS-data frames but cannot do so correctly
 *	for non-QoS-data and management frames because beacons need them from
 *	that counter as well and mac80211 cannot guarantee proper sequencing.
 *	If this flag is set, the driver should instruct the hardware to
 *	assign a sequence number to the frame or assign one itself. Cf. IEEE
 *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
 *	beacons and always be clear for frames without a sequence number field.
237 238 239 240 241 242
 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
 *	station
 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
243
 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
244
 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
245 246 247 248 249 250 251 252
 *	because the destination STA was in powersave mode. Note that to
 *	avoid race conditions, the filter must be set by the hardware or
 *	firmware upon receiving a frame that indicates that the station
 *	went to sleep (must be done on device to filter frames already on
 *	the queue) and may only be unset after mac80211 gives the OK for
 *	that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
 *	since only then is it guaranteed that no more frames are in the
 *	hardware queue.
253 254 255
 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
256 257
 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
 * 	so consider using block ack request (BAR).
258 259 260
 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
 *	set by rate control algorithms to indicate probe rate, will
 *	be cleared for fragmented frames (except on the last fragment)
261 262 263
 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
 *	used to indicate that a pending frame requires TX processing before
 *	it can be sent out.
264 265
 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
 *	used to indicate that a frame was already retried due to PS
Johannes Berg's avatar
Johannes Berg committed
266 267
 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
 *	used to indicate frame should not be encrypted
268 269 270
 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
 *	This frame is a response to a PS-poll frame and should be sent
 *	although the station is in powersave mode.
271 272 273 274
 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
 *	transmit function after the current frame, this can be used
 *	by drivers to kick the DMA queue only if unset or when the
 *	queue gets full.
275 276 277
 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
 *	after TX status because the destination was asleep, it must not
 *	be modified again (no seqno assignment, crypto, etc.)
278 279
 */
enum mac80211_tx_control_flags {
280
	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
281 282 283 284 285 286 287 288 289 290 291 292
	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
	IEEE80211_TX_CTL_AMPDU			= BIT(6),
	IEEE80211_TX_CTL_INJECTED		= BIT(7),
	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
	IEEE80211_TX_STAT_ACK			= BIT(9),
	IEEE80211_TX_STAT_AMPDU			= BIT(10),
	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
293
	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
294
	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
Johannes Berg's avatar
Johannes Berg committed
295
	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
296
	IEEE80211_TX_CTL_PSPOLL_RESPONSE	= BIT(17),
297
	IEEE80211_TX_CTL_MORE_FRAMES		= BIT(18),
298
	IEEE80211_TX_INTFL_RETRANSMISSION	= BIT(19),
299 300
};

301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320
/**
 * enum mac80211_rate_control_flags - per-rate flags set by the
 *	Rate Control algorithm.
 *
 * These flags are set by the Rate control algorithm for each rate during tx,
 * in the @flags member of struct ieee80211_tx_rate.
 *
 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
 *	This is set if the current BSS requires ERP protection.
 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
 * @IEEE80211_TX_RC_MCS: HT rate.
 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
 *	Greenfield mode.
 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
 *	adjacent 20 MHz channels, if the current channel type is
 *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
 */
321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336
enum mac80211_rate_control_flags {
	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),

	/* rate index is an MCS rate number instead of an index */
	IEEE80211_TX_RC_MCS			= BIT(3),
	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
};


/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
337

338 339
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
340

341 342
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES	5
343 344

/**
345
 * struct ieee80211_tx_rate - rate selection/status
346
 *
347 348
 * @idx: rate index to attempt to send with
 * @flags: rate control flags (&enum mac80211_rate_control_flags)
349
 * @count: number of tries in this rate before going to the next rate
350 351 352 353 354 355
 *
 * A value of -1 for @idx indicates an invalid rate and, if used
 * in an array of retry rates, that no more rates should be tried.
 *
 * When used for transmit status reporting, the driver should
 * always report the rate along with the flags it used.
356 357 358 359 360 361 362 363 364 365 366 367 368 369 370
 *
 * &struct ieee80211_tx_info contains an array of these structs
 * in the control information, and it will be filled by the rate
 * control algorithm according to what should be sent. For example,
 * if this array contains, in the format { <idx>, <count> } the
 * information
 *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
 * then this means that the frame should be transmitted
 * up to twice at rate 3, up to twice at rate 2, and up to four
 * times at rate 1 if it doesn't get acknowledged. Say it gets
 * acknowledged by the peer after the fifth attempt, the status
 * information should then contain
 *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
 * since it was transmitted twice at rate 3, twice at rate 2
 * and once at rate 1 after which we received an acknowledgement.
371
 */
372 373 374 375
struct ieee80211_tx_rate {
	s8 idx;
	u8 count;
	u8 flags;
376
} __attribute__((packed));
377

378 379 380 381 382 383 384 385
/**
 * struct ieee80211_tx_info - skb transmit information
 *
 * This structure is placed in skb->cb for three uses:
 *  (1) mac80211 TX control - mac80211 tells the driver what to do
 *  (2) driver internal use (if applicable)
 *  (3) TX status information - driver tells mac80211 what happened
 *
386 387 388
 * The TX control's sta pointer is only valid during the ->tx call,
 * it may be NULL.
 *
389
 * @flags: transmit info flags, defined above
390
 * @band: the band to transmit on (use for checking for races)
391
 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
392
 * @pad: padding, ignore
393 394 395
 * @control: union for control data
 * @status: union for status data
 * @driver_data: array of driver_data pointers
396
 * @ampdu_ack_len: number of acked aggregated frames.
397 398 399
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
 * @ampdu_ack_map: block ack bit map for the aggregation.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
400 401
 * @ampdu_len: number of aggregated frames.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
402
 * @ack_signal: signal strength of the ACK frame
403
 */
404 405 406 407
struct ieee80211_tx_info {
	/* common information */
	u32 flags;
	u8 band;
408

409
	u8 antenna_sel_tx;
410

411
	/* 2 byte hole */
412
	u8 pad[2];
413 414 415

	union {
		struct {
416 417 418 419 420 421 422 423 424 425
			union {
				/* rate control */
				struct {
					struct ieee80211_tx_rate rates[
						IEEE80211_TX_MAX_RATES];
					s8 rts_cts_rate_idx;
				};
				/* only needed before rate control */
				unsigned long jiffies;
			};
426
			/* NB: vif can be NULL for injected frames */
427 428
			struct ieee80211_vif *vif;
			struct ieee80211_key_conf *hw_key;
429
			struct ieee80211_sta *sta;
430 431
		} control;
		struct {
432 433
			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
			u8 ampdu_ack_len;
434 435
			u64 ampdu_ack_map;
			int ack_signal;
436 437
			u8 ampdu_len;
			/* 7 bytes free */
438
		} status;
439 440 441 442 443 444 445 446
		struct {
			struct ieee80211_tx_rate driver_rates[
				IEEE80211_TX_MAX_RATES];
			void *rate_driver_data[
				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
		};
		void *driver_data[
			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
447
	};
448 449
};

450 451 452 453
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
	return (struct ieee80211_tx_info *)skb->cb;
}
454

455 456 457 458 459
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
	return (struct ieee80211_rx_status *)skb->cb;
}

460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494
/**
 * ieee80211_tx_info_clear_status - clear TX status
 *
 * @info: The &struct ieee80211_tx_info to be cleared.
 *
 * When the driver passes an skb back to mac80211, it must report
 * a number of things in TX status. This function clears everything
 * in the TX status but the rate control information (it does clear
 * the count since you need to fill that in anyway).
 *
 * NOTE: You can only use this function if you do NOT use
 *	 info->driver_data! Use info->rate_driver_data
 *	 instead if you need only the less space that allows.
 */
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
	int i;

	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, control.rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, driver_rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
	/* clear the rate counts */
	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
		info->status.rates[i].count = 0;

	BUILD_BUG_ON(
	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
	memset(&info->status.ampdu_ack_len, 0,
	       sizeof(struct ieee80211_tx_info) -
	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}

495 496 497 498 499 500 501 502 503 504 505 506 507

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
508 509 510 511
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
512
 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
Bruno Randolf's avatar
Bruno Randolf committed
513 514
 *	is valid. This is useful in monitor mode and necessary for beacon frames
 *	to enable IBSS merging.
515
 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
516 517 518
 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
 * @RX_FLAG_SHORT_GI: Short guard interval was used
519 520 521
 * @RX_FLAG_INTERNAL_CMTR: set internally after frame was reported
 *	on cooked monitor to avoid double-reporting it for multiple
 *	virtual interfaces
522 523 524 525 526 527
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
528 529
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
530
	RX_FLAG_TSFT		= 1<<7,
531 532 533 534
	RX_FLAG_SHORTPRE	= 1<<8,
	RX_FLAG_HT		= 1<<9,
	RX_FLAG_40MHZ		= 1<<10,
	RX_FLAG_SHORT_GI	= 1<<11,
535
	RX_FLAG_INTERNAL_CMTR	= 1<<12,
536 537 538 539 540 541 542
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
543
 * frame, in the skb's control buffer (cb).
544
 *
545 546
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
547
 * @band: the active band when this frame was received
548
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
549 550 551 552
 * @signal: signal strength when receiving this frame, either in dBm, in dB or
 *	unspecified depending on the hardware capabilities flags
 *	@IEEE80211_HW_SIGNAL_*
 * @noise: noise when receiving this frame, in dBm.
553
 * @antenna: antenna used
554 555
 * @rate_idx: index of data rate into band's supported rates or MCS index if
 *	HT rates are use (RX_FLAG_HT)
556 557
 * @flag: %RX_FLAG_*
 */
558 559
struct ieee80211_rx_status {
	u64 mactime;
560
	enum ieee80211_band band;
561 562
	int freq;
	int signal;
563 564
	int noise;
	int antenna;
565
	int rate_idx;
566 567 568
	int flag;
};

569 570 571 572 573
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
574 575 576
 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
 *	to determine for example whether to calculate timestamps for packets
 *	or not, do not use instead of filter flags!
577 578 579 580 581 582 583
 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
 *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
 *	meaning that the hardware still wakes up for beacons, is able to
 *	transmit frames and receive the possible acknowledgment frames.
 *	Not to be confused with hardware specific wakeup/sleep states,
 *	driver is responsible for that. See the section "Powersave support"
 *	for more.
584 585 586 587 588
 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
 *	the driver should be prepared to handle configuration requests but
 *	may turn the device off as much as possible. Typically, this flag will
 *	be set when an interface is set UP but not associated or scanning, but
 *	it can also be unset in that case when monitor interfaces are active.
589 590
 */
enum ieee80211_conf_flags {
591
	IEEE80211_CONF_MONITOR		= (1<<0),
Johannes Berg's avatar
Johannes Berg committed
592
	IEEE80211_CONF_PS		= (1<<1),
593
	IEEE80211_CONF_IDLE		= (1<<2),
594
};
595

596

597 598 599 600
/**
 * enum ieee80211_conf_changed - denotes which configuration changed
 *
 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
601
 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
602
 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
603
 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
604
 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
605
 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
606
 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
607
 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
608 609
 */
enum ieee80211_conf_changed {
610
	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
611
	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
612
	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
613
	IEEE80211_CONF_CHANGE_PS		= BIT(4),
614 615 616
	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
617
	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
618 619
};

620 621 622
/**
 * enum ieee80211_smps_mode - spatial multiplexing power save mode
 *
623 624 625 626 627
 * @IEEE80211_SMPS_AUTOMATIC: automatic
 * @IEEE80211_SMPS_OFF: off
 * @IEEE80211_SMPS_STATIC: static
 * @IEEE80211_SMPS_DYNAMIC: dynamic
 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
628 629 630 631 632 633 634 635 636 637 638
 */
enum ieee80211_smps_mode {
	IEEE80211_SMPS_AUTOMATIC,
	IEEE80211_SMPS_OFF,
	IEEE80211_SMPS_STATIC,
	IEEE80211_SMPS_DYNAMIC,

	/* keep last */
	IEEE80211_SMPS_NUM_MODES,
};

639 640 641 642 643
/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
644 645
 * @flags: configuration flags defined above
 *
646
 * @listen_interval: listen interval in units of beacon interval
647
 * @max_sleep_period: the maximum number of beacon intervals to sleep for
648 649 650 651
 *	before checking the beacon for a TIM bit (managed mode only); this
 *	value will be only achievable between DTIM frames, the hardware
 *	needs to check for the multicast traffic bit in DTIM beacons.
 *	This variable is valid only when the CONF_PS flag is set.
652 653 654
 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
 *	in power saving. Power saving will not be enabled until a beacon
 *	has been received and the DTIM period is known.
655 656 657 658
 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
 *	powersave documentation below. This variable is valid only when
 *	the CONF_PS flag is set.
 *
659
 * @power_level: requested transmit power (in dBm)
660
 *
661
 * @channel: the channel to tune to
662
 * @channel_type: the channel (HT) type
663
 *
664 665 666 667 668 669
 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
 *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
 *    but actually means the number of transmissions not the number of retries
 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
 *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
 *    number of transmissions not the number of retries
670 671 672 673
 *
 * @smps_mode: spatial multiplexing powersave mode; note that
 *	%IEEE80211_SMPS_STATIC is used when the device is not
 *	configured for an HT channel
674 675
 */
struct ieee80211_conf {
676
	u32 flags;
677
	int power_level, dynamic_ps_timeout;
678
	int max_sleep_period;
679

680
	u16 listen_interval;
681
	u8 ps_dtim_period;
682

683 684
	u8 long_frame_max_tx_count, short_frame_max_tx_count;

685
	struct ieee80211_channel *channel;
686
	enum nl80211_channel_type channel_type;
687
	enum ieee80211_smps_mode smps_mode;
688 689
};

690 691 692 693 694 695
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
696
 * @type: type of this virtual interface
697 698
 * @bss_conf: BSS configuration for this interface, either our own
 *	or the BSS we're associated to
699
 * @addr: address of this interface
700 701 702 703
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
704
	enum nl80211_iftype type;
705
	struct ieee80211_bss_conf bss_conf;
706
	u8 addr[ETH_ALEN];
707 708 709 710
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

Johannes Berg's avatar
Johannes Berg committed
711 712 713
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
714
	return vif->type == NL80211_IFTYPE_MESH_POINT;
Johannes Berg's avatar
Johannes Berg committed
715 716 717 718
#endif
	return false;
}

719 720 721 722 723
/**
 * enum ieee80211_key_alg - key algorithm
 * @ALG_WEP: WEP40 or WEP104
 * @ALG_TKIP: TKIP
 * @ALG_CCMP: CCMP (AES)
724
 * @ALG_AES_CMAC: AES-128-CMAC
725
 */
726
enum ieee80211_key_alg {
727 728 729
	ALG_WEP,
	ALG_TKIP,
	ALG_CCMP,
730
	ALG_AES_CMAC,
731
};
732

733 734 735 736 737 738 739 740 741 742 743 744 745 746
/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
747 748
 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
 *	that the key is pairwise rather then a shared key.
749 750 751
 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
 *	CCMP key if it requires CCMP encryption of management frames (MFP) to
 *	be done in software.
752
 */
753 754 755 756
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
757
	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
758
	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
759
};
760

761 762 763 764 765 766 767 768
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
769
 *	encrypted in hardware.
770 771 772 773
 * @alg: The key algorithm.
 * @flags: key flags, see &enum ieee80211_key_flags.
 * @keyidx: the key index (0-3)
 * @keylen: key material length
774 775 776 777 778
 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
 * 	data block:
 * 	- Temporal Encryption Key (128 bits)
 * 	- Temporal Authenticator Tx MIC Key (64 bits)
 * 	- Temporal Authenticator Rx MIC Key (64 bits)
779 780
 * @icv_len: The ICV length for this key type
 * @iv_len: The IV length for this key type
781
 */
782
struct ieee80211_key_conf {
783
	enum ieee80211_key_alg alg;
784 785
	u8 icv_len;
	u8 iv_len;
786
	u8 hw_key_idx;
787 788 789
	u8 flags;
	s8 keyidx;
	u8 keylen;
790 791 792
	u8 key[0];
};

793 794 795 796 797 798 799 800 801
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
802
enum set_key_cmd {
803
	SET_KEY, DISABLE_KEY,
804
};
805

806 807 808 809 810 811 812 813 814 815 816 817
/**
 * struct ieee80211_sta - station table entry
 *
 * A station table entry represents a station we are possibly
 * communicating with. Since stations are RCU-managed in
 * mac80211, any ieee80211_sta pointer you get access to must
 * either be protected by rcu_read_lock() explicitly or implicitly,
 * or you must take good care to not use such a pointer after a
 * call to your sta_notify callback that removed it.
 *
 * @addr: MAC address
 * @aid: AID we assigned to the station if we're an AP
818
 * @supp_rates: Bitmap of supported rates (per band)
Johannes Berg's avatar
Johannes Berg committed
819
 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
820 821 822 823
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *), size is determined in hw information.
 */
struct ieee80211_sta {
824
	u32 supp_rates[IEEE80211_NUM_BANDS];
825 826
	u8 addr[ETH_ALEN];
	u16 aid;
827
	struct ieee80211_sta_ht_cap ht_cap;
828 829 830 831 832

	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

833 834 835 836
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
837 838
 * indicates addition and removal of a station to station table,
 * or if a associated station made a power state transition.
839 840 841
 *
 * @STA_NOTIFY_ADD: a station was added to the station table
 * @STA_NOTIFY_REMOVE: a station being removed from the station table
842 843 844
 * @STA_NOTIFY_SLEEP: a station is now sleeping
 * @STA_NOTIFY_AWAKE: a sleeping station woke up
 */
845 846
enum sta_notify_cmd {
	STA_NOTIFY_ADD, STA_NOTIFY_REMOVE,
847 848 849
	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};

850 851 852 853 854 855 856 857 858 859 860 861 862 863 864
/**
 * enum ieee80211_tkip_key_type - get tkip key
 *
 * Used by drivers which need to get a tkip key for skb. Some drivers need a
 * phase 1 key, others need a phase 2 key. A single function allows the driver
 * to get the key, this enum indicates what type of key is required.
 *
 * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
 * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
 */
enum ieee80211_tkip_key_type {
	IEEE80211_TKIP_P1_KEY,
	IEEE80211_TKIP_P2_KEY,
};

865 866 867 868 869 870 871 872 873
/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
874 875 876 877 878 879 880 881 882 883 884 885 886
 * @IEEE80211_HW_HAS_RATE_CONTROL:
 *	The hardware or firmware includes rate control, and cannot be
 *	controlled by the stack. As such, no rate control algorithm
 *	should be instantiated, and the TX rate reported to userspace
 *	will be taken from the TX status instead of the rate control
 *	algorithm.
 *	Note that this requires that the driver implement a number of
 *	callbacks so it has the correct information, it needs to have
 *	the @set_rts_threshold callback and must look at the BSS config
 *	@use_cts_prot for G/N protection, @use_short_slot for slot
 *	timing in 2.4 GHz and @use_short_preamble for preambles for
 *	CCK frames.
 *
887 888 889 890 891 892 893 894 895 896
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
897
 *	the driver can fetch them with ieee80211_get_buffered_bc().
898
 *
899 900 901 902 903 904
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
905 906 907 908 909 910 911 912 913 914 915 916 917 918
 *
 * @IEEE80211_HW_SIGNAL_UNSPEC:
 *	Hardware can provide signal values but we don't know its units. We
 *	expect values between 0 and @max_signal.
 *	If possible please provide dB or dBm instead.
 *
 * @IEEE80211_HW_SIGNAL_DBM:
 *	Hardware gives signal values in dBm, decibel difference from
 *	one milliwatt. This is the preferred method since it is standardized
 *	between different devices. @max_signal does not need to be set.
 *
 * @IEEE80211_HW_NOISE_DBM:
 *	Hardware can provide noise (radio interference) values in units dBm,
 *      decibel difference from one milliwatt.
919 920 921 922
 *
 * @IEEE80211_HW_SPECTRUM_MGMT:
 * 	Hardware supports spectrum management defined in 802.11h
 * 	Measurement, Channel Switch, Quieting, TPC
Sujith's avatar
Sujith committed
923 924 925
 *
 * @IEEE80211_HW_AMPDU_AGGREGATION:
 *	Hardware supports 11n A-MPDU aggregation.
926
 *
927 928 929 930 931 932 933 934 935
 * @IEEE80211_HW_SUPPORTS_PS:
 *	Hardware has power save support (i.e. can go to sleep).
 *
 * @IEEE80211_HW_PS_NULLFUNC_STACK:
 *	Hardware requires nullfunc frame handling in stack, implies
 *	stack support for dynamic PS.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
 *	Hardware has support for dynamic PS.
936 937 938
 *
 * @IEEE80211_HW_MFP_CAPABLE:
 *	Hardware supports management frame protection (MFP, IEEE 802.11w).
939 940 941 942
 *
 * @IEEE80211_HW_BEACON_FILTER:
 *	Hardware supports dropping of irrelevant beacon frames to
 *	avoid waking up cpu.
943 944 945 946 947 948 949 950 951 952
 *
 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
 *	Hardware supports static spatial multiplexing powersave,
 *	ie. can turn off all but one chain even on HT connections
 *	that should be using more chains.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
 *	Hardware supports dynamic spatial multiplexing powersave,
 *	ie. can turn off all but one chain and then wake the rest
 *	up as required after, for example, rts/cts handshake.
953 954 955 956 957
 *
 * @IEEE80211_HW_SUPPORTS_UAPSD:
 *	Hardware supports Unscheduled Automatic Power Save Delivery
 *	(U-APSD) in managed mode. The mode is configured with
 *	conf_tx() operation.
958 959
 */
enum ieee80211_hw_flags {
960
	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
961 962
	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
963 964
	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
965
	IEEE80211_HW_SIGNAL_UNSPEC			= 1<<5,
Johannes Berg's avatar
Johannes Berg committed
966 967 968 969 970 971 972 973
	IEEE80211_HW_SIGNAL_DBM				= 1<<6,
	IEEE80211_HW_NOISE_DBM				= 1<<7,
	IEEE80211_HW_SPECTRUM_MGMT			= 1<<8,
	IEEE80211_HW_AMPDU_AGGREGATION			= 1<<9,
	IEEE80211_HW_SUPPORTS_PS			= 1<<10,
	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
974
	IEEE80211_HW_BEACON_FILTER			= 1<<14,
975 976
	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
977
	IEEE80211_HW_SUPPORTS_UAPSD			= 1<<17,
978 979
};

980 981
/**
 * struct ieee80211_hw - hardware information and state
982 983 984 985 986 987 988
 *
 * This structure contains the configuration and hardware
 * information for an 802.11 PHY.
 *
 * @wiphy: This points to the &struct wiphy allocated for this
 *	802.11 PHY. You must fill in the @perm_addr and @dev
 *	members of this structure using SET_IEEE80211_DEV()
989 990
 *	and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
 *	bands (with channels, bitrates) are registered here.
991 992 993 994 995 996 997 998 999 1000 1001 1002 1003
 *
 * @conf: &struct ieee80211_conf, device configuration, don't use.
 *
 * @priv: pointer to private area that was allocated for driver use
 *	along with this structure.
 *
 * @flags: hardware flags, see &enum ieee80211_hw_flags.
 *
 * @extra_tx_headroom: headroom to reserve in each transmit skb
 *	for use by the driver (e.g. for transmit headers.)
 *
 * @channel_change_time: time (in microseconds) it takes to change channels.
 *
1004 1005
 * @max_signal: Maximum value for signal (rssi) in RX information, used
 *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
1006
 *
1007 1008 1009
 * @max_listen_interval: max listen interval in units of beacon interval
 *     that HW supports
 *
1010
 * @queues: number of available hardware transmit queues for
Johannes Berg's avatar
Johannes Berg committed
1011 1012 1013
 *	data packets. WMM/QoS requires at least four, these
 *	queues need to have configurable access parameters.
 *
1014 1015 1016
 * @rate_control_algorithm: rate control algorithm for this hardware.
 *	If unset (NULL), the default algorithm will be used. Must be
 *	set before calling ieee80211_register_hw().
1017 1018 1019
 *
 * @vif_data_size: size (in bytes) of the drv_priv data area
 *	within &struct ieee80211_vif.
1020 1021
 * @sta_data_size: size (in bytes) of the drv_priv data area
 *	within &struct ieee80211_sta.
1022
 *
1023 1024
 * @max_rates: maximum number of alternate rate retry stages
 * @max_rate_tries: maximum number of tries for each stage
1025
 */
1026 1027
struct ieee80211_hw {
	struct ieee80211_conf conf;
1028
	struct wiphy *wiphy;
1029
	const char *rate_control_algorithm;
1030
	void *priv;
1031
	u32 flags;
1032 1033
	unsigned int extra_tx_headroom;
	int channel_change_time;
1034
	int vif_data_size;
1035
	int sta_data_size;
1036 1037
	u16 queues;
	u16 max_listen_interval;
1038
	s8 max_signal;
1039 1040
	u8 max_rates;
	u8 max_rate_tries;
1041 1042
};

1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055
/**
 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
 *
 * @wiphy: the &struct wiphy which we want to query
 *
 * mac80211 drivers can use this to get to their respective
 * &struct ieee80211_hw. Drivers wishing to get to their own private
 * structure can then access it via hw->priv. Note that mac802111 drivers should
 * not use wiphy_priv() to try to get their private driver structure as this
 * is already used internally by mac80211.
 */
struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);

1056 1057 1058 1059 1060 1061
/**
 * SET_IEEE80211_DEV - set device for 802.11 hardware
 *
 * @hw: the &struct ieee80211_hw to set the device for
 * @dev: the &struct device of this 802.11 device
 */
1062 1063 1064 1065 1066
static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
	set_wiphy_dev(hw->wiphy, dev);
}

1067
/**
1068
 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
1069 1070 1071 1072
 *
 * @hw: the &struct ieee80211_hw to set the MAC address for
 * @addr: the address to set
 */
1073 1074 1075 1076 1077
static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)