mac80211.h 130 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
6
 * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/cfg80211.h>
22
#include <asm/unaligned.h>
23

24 25 26 27 28 29 30 31 32 33 34 35 36
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 38 39
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
40 41 42 43
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44
 *	 use the non-IRQ-safe functions!
45 46
 */

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
73 74
 */

75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
/**
 * DOC: mac80211 workqueue
 *
 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
 * The workqueue is a single threaded workqueue and can only be accessed by
 * helpers for sanity checking. Drivers must ensure all work added onto the
 * mac80211 workqueue should be cancelled on the driver stop() callback.
 *
 * mac80211 will flushed the workqueue upon interface removal and during
 * suspend.
 *
 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
 *
 */

Johannes Berg's avatar
Johannes Berg committed
90 91 92 93 94 95
/**
 * enum ieee80211_max_queues - maximum number of queues
 *
 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
 */
enum ieee80211_max_queues {
96
	IEEE80211_MAX_QUEUES =		4,
Johannes Berg's avatar
Johannes Berg committed
97 98
};

99 100 101 102 103 104 105 106 107 108 109 110 111 112
/**
 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
 * @IEEE80211_AC_VO: voice
 * @IEEE80211_AC_VI: video
 * @IEEE80211_AC_BE: best effort
 * @IEEE80211_AC_BK: background
 */
enum ieee80211_ac_numbers {
	IEEE80211_AC_VO		= 0,
	IEEE80211_AC_VI		= 1,
	IEEE80211_AC_BE		= 2,
	IEEE80211_AC_BK		= 3,
};

113 114 115 116
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
117
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
118
 *
119
 * @aifs: arbitration interframe space [0..255]
120 121
 * @cw_min: minimum contention window [a value of the form
 *	2^n-1 in the range 1..32767]
122
 * @cw_max: maximum contention window [like @cw_min]
123
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
124
 * @uapsd: is U-APSD mode enabled for the queue
125
 */
126
struct ieee80211_tx_queue_params {
127
	u16 txop;
128 129
	u16 cw_min;
	u16 cw_max;
130
	u8 aifs;
131
	bool uapsd;
132 133 134 135 136 137 138 139 140
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

141 142 143 144 145 146 147 148 149 150
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
151
 * @BSS_CHANGED_ERP_SLOT: slot timing changed
Tomas Winkler's avatar
Tomas Winkler committed
152
 * @BSS_CHANGED_HT: 802.11n parameters changed
153
 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
154
 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
155 156 157 158 159 160
 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
 *	reason (IBSS and managed mode)
 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
 *	new beacon (beaconing modes)
 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
 *	enabled/disabled (beaconing modes)
161
 * @BSS_CHANGED_CQM: Connection quality monitor config changed
162
 * @BSS_CHANGED_IBSS: IBSS join status changed
163
 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
164 165
 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
 *	that it is only ever disabled for station mode.
166
 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
167 168 169 170 171
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
172
	BSS_CHANGED_ERP_SLOT		= 1<<3,
Tomas Winkler's avatar
Tomas Winkler committed
173
	BSS_CHANGED_HT                  = 1<<4,
174
	BSS_CHANGED_BASIC_RATES		= 1<<5,
175
	BSS_CHANGED_BEACON_INT		= 1<<6,
176 177 178
	BSS_CHANGED_BSSID		= 1<<7,
	BSS_CHANGED_BEACON		= 1<<8,
	BSS_CHANGED_BEACON_ENABLED	= 1<<9,
179
	BSS_CHANGED_CQM			= 1<<10,
180
	BSS_CHANGED_IBSS		= 1<<11,
181
	BSS_CHANGED_ARP_FILTER		= 1<<12,
182
	BSS_CHANGED_QOS			= 1<<13,
183
	BSS_CHANGED_IDLE		= 1<<14,
184 185

	/* when adding here, make sure to change ieee80211_reconfig */
186 187
};

188 189 190 191 192 193 194
/*
 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
 * of addresses for an interface increase beyond this value, hardware ARP
 * filtering will be disabled.
 */
#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4

195 196 197 198 199 200 201 202 203 204 205
/**
 * enum ieee80211_rssi_event - RSSI threshold event
 * An indicator for when RSSI goes below/above a certain threshold.
 * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver.
 * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver.
 */
enum ieee80211_rssi_event {
	RSSI_EVENT_HIGH,
	RSSI_EVENT_LOW,
};

206 207 208 209 210 211 212
/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
213 214
 * @ibss_joined: indicates whether this station is part of an IBSS
 *	or not
215 216
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
217 218 219 220 221 222
 * @use_short_preamble: use 802.11b short preamble;
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
 * @use_short_slot: use short slot time (only relevant for ERP);
 *	if the hardware cannot handle this it must set the
 *	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
223
 * @dtim_period: num of beacons before the next DTIM, for beaconing,
224 225 226
 *	valid in station mode only while @assoc is true and if also
 *	requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf
 *	@ps_dtim_period)
227 228
 * @timestamp: beacon timestamp
 * @beacon_int: beacon interval
229
 * @assoc_capability: capabilities taken from assoc resp
230 231 232
 * @basic_rates: bitmap of basic rates, each bit stands for an
 *	index into the rate table configured by the driver in
 *	the current band.
233
 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
234 235
 * @bssid: The BSSID for this BSS
 * @enable_beacon: whether beaconing should be enabled or not
236 237 238
 * @channel_type: Channel type for this BSS -- the hardware might be
 *	configured for HT40+ while this BSS only uses no-HT, for
 *	example.
239 240
 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
 *	This field is only valid when the channel type is one of the HT types.
241 242 243
 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
 *	implies disabled
 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
244 245 246 247 248 249 250 251 252
 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
 *	may filter ARP queries targeted for other addresses than listed here.
 *	The driver must allow ARP queries targeted for all address listed here
 *	to pass through. An empty list implies no ARP queries need to pass.
 * @arp_addr_cnt: Number of addresses currently on the list.
 * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may
 *	filter ARP queries based on the @arp_addr_list, if disabled, the
 *	hardware must not perform any ARP filtering. Note, that the filter will
 *	be enabled also in promiscuous mode.
253
 * @qos: This is a QoS-enabled BSS.
254 255 256
 * @idle: This interface is idle. There's also a global idle flag in the
 *	hardware config which may be more appropriate depending on what
 *	your driver/device needs to do.
257 258
 */
struct ieee80211_bss_conf {
259
	const u8 *bssid;
260
	/* association related data */
261
	bool assoc, ibss_joined;
262 263 264 265
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
266
	bool use_short_slot;
267
	bool enable_beacon;
268
	u8 dtim_period;
269 270 271
	u16 beacon_int;
	u16 assoc_capability;
	u64 timestamp;
272
	u32 basic_rates;
273
	int mcast_rate[IEEE80211_NUM_BANDS];
274
	u16 ht_operation_mode;
275 276
	s32 cqm_rssi_thold;
	u32 cqm_rssi_hyst;
277
	enum nl80211_channel_type channel_type;
278 279 280
	__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
	u8 arp_addr_cnt;
	bool arp_filter_enabled;
281
	bool qos;
282
	bool idle;
283 284
};

285
/**
286
 * enum mac80211_tx_control_flags - flags to describe transmission information/status
287
 *
288
 * These flags are used with the @flags member of &ieee80211_tx_info.
289
 *
290
 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
291 292 293 294 295 296 297 298 299 300 301
 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
 *	number to this frame, taking care of not overwriting the fragment
 *	number and increasing the sequence number only when the
 *	IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
 *	assign sequence numbers to QoS-data frames but cannot do so correctly
 *	for non-QoS-data and management frames because beacons need them from
 *	that counter as well and mac80211 cannot guarantee proper sequencing.
 *	If this flag is set, the driver should instruct the hardware to
 *	assign a sequence number to the frame or assign one itself. Cf. IEEE
 *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
 *	beacons and always be clear for frames without a sequence number field.
302 303 304 305 306 307
 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
 *	station
 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
308
 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
309
 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
310 311 312 313 314 315 316 317
 *	because the destination STA was in powersave mode. Note that to
 *	avoid race conditions, the filter must be set by the hardware or
 *	firmware upon receiving a frame that indicates that the station
 *	went to sleep (must be done on device to filter frames already on
 *	the queue) and may only be unset after mac80211 gives the OK for
 *	that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
 *	since only then is it guaranteed that no more frames are in the
 *	hardware queue.
318 319 320
 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
321 322
 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
 * 	so consider using block ack request (BAR).
323 324 325
 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
 *	set by rate control algorithms to indicate probe rate, will
 *	be cleared for fragmented frames (except on the last fragment)
326 327 328
 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
 *	used to indicate that a pending frame requires TX processing before
 *	it can be sent out.
329 330
 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
 *	used to indicate that a frame was already retried due to PS
Johannes Berg's avatar
Johannes Berg committed
331 332
 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
 *	used to indicate frame should not be encrypted
333 334 335
 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?)
 *	This frame is a response to a PS-poll frame and should be sent
 *	although the station is in powersave mode.
336 337 338 339
 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
 *	transmit function after the current frame, this can be used
 *	by drivers to kick the DMA queue only if unset or when the
 *	queue gets full.
340 341 342
 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
 *	after TX status because the destination was asleep, it must not
 *	be modified again (no seqno assignment, crypto, etc.)
343 344
 * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still
 *	has a radiotap header at skb->data.
345 346 347
 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
 *	MLME command (internal to mac80211 to figure out whether to send TX
 *	status to user space)
348
 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
349 350
 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
 *	frame and selects the maximum number of streams that it can use.
351 352 353 354
 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
 *	the off-channel channel when a remain-on-channel offload is done
 *	in hardware -- normal packets still flow and are expected to be
 *	handled properly by the device.
355 356 357
 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
 *	testing. It will be sent out with incorrect Michael MIC key to allow
 *	TKIP countermeasures to be tested.
358 359 360
 *
 * Note: If you have to add new flags to the enumeration, then don't
 *	 forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
361 362
 */
enum mac80211_tx_control_flags {
363
	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
364 365 366 367 368 369 370 371 372 373 374 375
	IEEE80211_TX_CTL_ASSIGN_SEQ		= BIT(1),
	IEEE80211_TX_CTL_NO_ACK			= BIT(2),
	IEEE80211_TX_CTL_CLEAR_PS_FILT		= BIT(3),
	IEEE80211_TX_CTL_FIRST_FRAGMENT		= BIT(4),
	IEEE80211_TX_CTL_SEND_AFTER_DTIM	= BIT(5),
	IEEE80211_TX_CTL_AMPDU			= BIT(6),
	IEEE80211_TX_CTL_INJECTED		= BIT(7),
	IEEE80211_TX_STAT_TX_FILTERED		= BIT(8),
	IEEE80211_TX_STAT_ACK			= BIT(9),
	IEEE80211_TX_STAT_AMPDU			= BIT(10),
	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
376
	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
377
	IEEE80211_TX_INTFL_RETRIED		= BIT(15),
Johannes Berg's avatar
Johannes Berg committed
378
	IEEE80211_TX_INTFL_DONT_ENCRYPT		= BIT(16),
379
	IEEE80211_TX_CTL_PSPOLL_RESPONSE	= BIT(17),
380
	IEEE80211_TX_CTL_MORE_FRAMES		= BIT(18),
381
	IEEE80211_TX_INTFL_RETRANSMISSION	= BIT(19),
382
	IEEE80211_TX_INTFL_HAS_RADIOTAP		= BIT(20),
383
	IEEE80211_TX_INTFL_NL80211_FRAME_TX	= BIT(21),
384
	IEEE80211_TX_CTL_LDPC			= BIT(22),
385
	IEEE80211_TX_CTL_STBC			= BIT(23) | BIT(24),
386
	IEEE80211_TX_CTL_TX_OFFCHAN		= BIT(25),
387
	IEEE80211_TX_INTFL_TKIP_MIC_FAILURE	= BIT(26),
388 389
};

Johannes Berg's avatar
Johannes Berg committed
390 391
#define IEEE80211_TX_CTL_STBC_SHIFT		23

392 393 394 395 396 397 398 399 400 401 402 403 404
/*
 * This definition is used as a mask to clear all temporary flags, which are
 * set by the tx handlers for each transmission attempt by the mac80211 stack.
 */
#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK |		      \
	IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT |    \
	IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU |	      \
	IEEE80211_TX_STAT_TX_FILTERED |	IEEE80211_TX_STAT_ACK |		      \
	IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK |	      \
	IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \
	IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC |		      \
	IEEE80211_TX_CTL_STBC)

405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424
/**
 * enum mac80211_rate_control_flags - per-rate flags set by the
 *	Rate Control algorithm.
 *
 * These flags are set by the Rate control algorithm for each rate during tx,
 * in the @flags member of struct ieee80211_tx_rate.
 *
 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
 *	This is set if the current BSS requires ERP protection.
 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
 * @IEEE80211_TX_RC_MCS: HT rate.
 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
 *	Greenfield mode.
 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
 *	adjacent 20 MHz channels, if the current channel type is
 *	NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
 */
425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440
enum mac80211_rate_control_flags {
	IEEE80211_TX_RC_USE_RTS_CTS		= BIT(0),
	IEEE80211_TX_RC_USE_CTS_PROTECT		= BIT(1),
	IEEE80211_TX_RC_USE_SHORT_PREAMBLE	= BIT(2),

	/* rate index is an MCS rate number instead of an index */
	IEEE80211_TX_RC_MCS			= BIT(3),
	IEEE80211_TX_RC_GREEN_FIELD		= BIT(4),
	IEEE80211_TX_RC_40_MHZ_WIDTH		= BIT(5),
	IEEE80211_TX_RC_DUP_DATA		= BIT(6),
	IEEE80211_TX_RC_SHORT_GI		= BIT(7),
};


/* there are 40 bytes if you don't need the rateset to be kept */
#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
441

442 443
/* if you do need the rateset, then you have less space */
#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
444

445 446
/* maximum number of rate stages */
#define IEEE80211_TX_MAX_RATES	5
447 448

/**
449
 * struct ieee80211_tx_rate - rate selection/status
450
 *
451 452
 * @idx: rate index to attempt to send with
 * @flags: rate control flags (&enum mac80211_rate_control_flags)
453
 * @count: number of tries in this rate before going to the next rate
454 455 456 457 458 459
 *
 * A value of -1 for @idx indicates an invalid rate and, if used
 * in an array of retry rates, that no more rates should be tried.
 *
 * When used for transmit status reporting, the driver should
 * always report the rate along with the flags it used.
460 461 462 463 464 465 466 467 468 469 470 471 472 473 474
 *
 * &struct ieee80211_tx_info contains an array of these structs
 * in the control information, and it will be filled by the rate
 * control algorithm according to what should be sent. For example,
 * if this array contains, in the format { <idx>, <count> } the
 * information
 *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
 * then this means that the frame should be transmitted
 * up to twice at rate 3, up to twice at rate 2, and up to four
 * times at rate 1 if it doesn't get acknowledged. Say it gets
 * acknowledged by the peer after the fifth attempt, the status
 * information should then contain
 *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
 * since it was transmitted twice at rate 3, twice at rate 2
 * and once at rate 1 after which we received an acknowledgement.
475
 */
476 477 478 479
struct ieee80211_tx_rate {
	s8 idx;
	u8 count;
	u8 flags;
480
} __packed;
481

482 483 484 485 486 487 488 489
/**
 * struct ieee80211_tx_info - skb transmit information
 *
 * This structure is placed in skb->cb for three uses:
 *  (1) mac80211 TX control - mac80211 tells the driver what to do
 *  (2) driver internal use (if applicable)
 *  (3) TX status information - driver tells mac80211 what happened
 *
490 491 492
 * The TX control's sta pointer is only valid during the ->tx call,
 * it may be NULL.
 *
493
 * @flags: transmit info flags, defined above
494
 * @band: the band to transmit on (use for checking for races)
495
 * @antenna_sel_tx: antenna to use, 0 for automatic diversity
496
 * @pad: padding, ignore
497 498 499
 * @control: union for control data
 * @status: union for status data
 * @driver_data: array of driver_data pointers
500
 * @ampdu_ack_len: number of acked aggregated frames.
501
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
502
 * @ampdu_len: number of aggregated frames.
503
 * 	relevant only if IEEE80211_TX_STAT_AMPDU was set.
504
 * @ack_signal: signal strength of the ACK frame
505
 */
506 507 508 509
struct ieee80211_tx_info {
	/* common information */
	u32 flags;
	u8 band;
510

511
	u8 antenna_sel_tx;
512

513
	/* 2 byte hole */
514
	u8 pad[2];
515 516 517

	union {
		struct {
518 519 520 521 522 523 524 525 526 527
			union {
				/* rate control */
				struct {
					struct ieee80211_tx_rate rates[
						IEEE80211_TX_MAX_RATES];
					s8 rts_cts_rate_idx;
				};
				/* only needed before rate control */
				unsigned long jiffies;
			};
528
			/* NB: vif can be NULL for injected frames */
529 530
			struct ieee80211_vif *vif;
			struct ieee80211_key_conf *hw_key;
531
			struct ieee80211_sta *sta;
532 533
		} control;
		struct {
534 535
			struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
			u8 ampdu_ack_len;
536
			int ack_signal;
537
			u8 ampdu_len;
538
			/* 15 bytes free */
539
		} status;
540 541 542 543 544 545 546 547
		struct {
			struct ieee80211_tx_rate driver_rates[
				IEEE80211_TX_MAX_RATES];
			void *rate_driver_data[
				IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
		};
		void *driver_data[
			IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
548
	};
549 550
};

551
/**
552
 * struct ieee80211_sched_scan_ies - scheduled scan IEs
553 554 555 556 557 558 559 560 561 562 563 564 565
 *
 * This structure is used to pass the appropriate IEs to be used in scheduled
 * scans for all bands.  It contains both the IEs passed from the userspace
 * and the ones generated by mac80211.
 *
 * @ie: array with the IEs for each supported band
 * @len: array with the total length of the IEs for each band
 */
struct ieee80211_sched_scan_ies {
	u8 *ie[IEEE80211_NUM_BANDS];
	size_t len[IEEE80211_NUM_BANDS];
};

566 567 568 569
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
	return (struct ieee80211_tx_info *)skb->cb;
}
570

571 572 573 574 575
static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
{
	return (struct ieee80211_rx_status *)skb->cb;
}

576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610
/**
 * ieee80211_tx_info_clear_status - clear TX status
 *
 * @info: The &struct ieee80211_tx_info to be cleared.
 *
 * When the driver passes an skb back to mac80211, it must report
 * a number of things in TX status. This function clears everything
 * in the TX status but the rate control information (it does clear
 * the count since you need to fill that in anyway).
 *
 * NOTE: You can only use this function if you do NOT use
 *	 info->driver_data! Use info->rate_driver_data
 *	 instead if you need only the less space that allows.
 */
static inline void
ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
{
	int i;

	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, control.rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
		     offsetof(struct ieee80211_tx_info, driver_rates));
	BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
	/* clear the rate counts */
	for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
		info->status.rates[i].count = 0;

	BUILD_BUG_ON(
	    offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23);
	memset(&info->status.ampdu_ack_len, 0,
	       sizeof(struct ieee80211_tx_info) -
	       offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
}

611 612 613 614 615 616 617 618 619 620 621 622 623

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
624 625 626 627
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
Johannes Berg's avatar
Johannes Berg committed
628 629 630 631
 * @RX_FLAG_MACTIME_MPDU: The timestamp passed in the RX status (@mactime
 *	field) is valid and contains the time the first symbol of the MPDU
 *	was received. This is useful in monitor mode and for proper IBSS
 *	merging.
632
 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
633 634 635
 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
 * @RX_FLAG_SHORT_GI: Short guard interval was used
636 637 638 639 640 641
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
642 643
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
Johannes Berg's avatar
Johannes Berg committed
644
	RX_FLAG_MACTIME_MPDU	= 1<<7,
645 646 647 648
	RX_FLAG_SHORTPRE	= 1<<8,
	RX_FLAG_HT		= 1<<9,
	RX_FLAG_40MHZ		= 1<<10,
	RX_FLAG_SHORT_GI	= 1<<11,
649 650 651 652 653 654 655
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
656
 * frame, in the skb's control buffer (cb).
657
 *
658 659
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
660
 * @band: the active band when this frame was received
661
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
662 663 664
 * @signal: signal strength when receiving this frame, either in dBm, in dB or
 *	unspecified depending on the hardware capabilities flags
 *	@IEEE80211_HW_SIGNAL_*
665
 * @antenna: antenna used
666 667
 * @rate_idx: index of data rate into band's supported rates or MCS index if
 *	HT rates are use (RX_FLAG_HT)
668
 * @flag: %RX_FLAG_*
669
 * @rx_flags: internal RX flags for mac80211
670
 */
671 672
struct ieee80211_rx_status {
	u64 mactime;
673
	enum ieee80211_band band;
674 675
	int freq;
	int signal;
676
	int antenna;
677
	int rate_idx;
678
	int flag;
679
	unsigned int rx_flags;
680 681
};

682 683 684 685 686
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
687 688 689
 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
 *	to determine for example whether to calculate timestamps for packets
 *	or not, do not use instead of filter flags!
690 691 692 693 694 695 696
 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
 *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
 *	meaning that the hardware still wakes up for beacons, is able to
 *	transmit frames and receive the possible acknowledgment frames.
 *	Not to be confused with hardware specific wakeup/sleep states,
 *	driver is responsible for that. See the section "Powersave support"
 *	for more.
697 698 699 700 701
 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
 *	the driver should be prepared to handle configuration requests but
 *	may turn the device off as much as possible. Typically, this flag will
 *	be set when an interface is set UP but not associated or scanning, but
 *	it can also be unset in that case when monitor interfaces are active.
702 703
 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
 *	operating channel.
704 705
 */
enum ieee80211_conf_flags {
706
	IEEE80211_CONF_MONITOR		= (1<<0),
Johannes Berg's avatar
Johannes Berg committed
707
	IEEE80211_CONF_PS		= (1<<1),
708
	IEEE80211_CONF_IDLE		= (1<<2),
709
	IEEE80211_CONF_OFFCHANNEL	= (1<<3),
710
};
711

712

713 714 715 716
/**
 * enum ieee80211_conf_changed - denotes which configuration changed
 *
 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
717
 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
718
 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
719
 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
720
 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
721
 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
722
 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
723
 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
724 725
 */
enum ieee80211_conf_changed {
726
	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
727
	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
728
	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
729
	IEEE80211_CONF_CHANGE_PS		= BIT(4),
730 731 732
	IEEE80211_CONF_CHANGE_POWER		= BIT(5),
	IEEE80211_CONF_CHANGE_CHANNEL		= BIT(6),
	IEEE80211_CONF_CHANGE_RETRY_LIMITS	= BIT(7),
733
	IEEE80211_CONF_CHANGE_IDLE		= BIT(8),
734 735
};

736 737 738
/**
 * enum ieee80211_smps_mode - spatial multiplexing power save mode
 *
739 740 741 742 743
 * @IEEE80211_SMPS_AUTOMATIC: automatic
 * @IEEE80211_SMPS_OFF: off
 * @IEEE80211_SMPS_STATIC: static
 * @IEEE80211_SMPS_DYNAMIC: dynamic
 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
744 745 746 747 748 749 750 751 752 753 754
 */
enum ieee80211_smps_mode {
	IEEE80211_SMPS_AUTOMATIC,
	IEEE80211_SMPS_OFF,
	IEEE80211_SMPS_STATIC,
	IEEE80211_SMPS_DYNAMIC,

	/* keep last */
	IEEE80211_SMPS_NUM_MODES,
};

755 756 757 758 759
/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
760 761
 * @flags: configuration flags defined above
 *
762
 * @listen_interval: listen interval in units of beacon interval
763
 * @max_sleep_period: the maximum number of beacon intervals to sleep for
764 765 766 767
 *	before checking the beacon for a TIM bit (managed mode only); this
 *	value will be only achievable between DTIM frames, the hardware
 *	needs to check for the multicast traffic bit in DTIM beacons.
 *	This variable is valid only when the CONF_PS flag is set.
768 769 770
 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
 *	in power saving. Power saving will not be enabled until a beacon
 *	has been received and the DTIM period is known.
771 772 773 774
 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
 *	powersave documentation below. This variable is valid only when
 *	the CONF_PS flag is set.
 *
775
 * @power_level: requested transmit power (in dBm)
776
 *
777
 * @channel: the channel to tune to
778
 * @channel_type: the channel (HT) type
779
 *
780 781 782 783 784 785
 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
 *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
 *    but actually means the number of transmissions not the number of retries
 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
 *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
 *    number of transmissions not the number of retries
786 787 788 789
 *
 * @smps_mode: spatial multiplexing powersave mode; note that
 *	%IEEE80211_SMPS_STATIC is used when the device is not
 *	configured for an HT channel
790 791
 */
struct ieee80211_conf {
792
	u32 flags;
793
	int power_level, dynamic_ps_timeout;
794
	int max_sleep_period;
795

796
	u16 listen_interval;
797
	u8 ps_dtim_period;
798

799 800
	u8 long_frame_max_tx_count, short_frame_max_tx_count;

801
	struct ieee80211_channel *channel;
802
	enum nl80211_channel_type channel_type;
803
	enum ieee80211_smps_mode smps_mode;
804 805
};

806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827
/**
 * struct ieee80211_channel_switch - holds the channel switch data
 *
 * The information provided in this structure is required for channel switch
 * operation.
 *
 * @timestamp: value in microseconds of the 64-bit Time Synchronization
 *	Function (TSF) timer when the frame containing the channel switch
 *	announcement was received. This is simply the rx.mactime parameter
 *	the driver passed into mac80211.
 * @block_tx: Indicates whether transmission must be blocked before the
 *	scheduled channel switch, as indicated by the AP.
 * @channel: the new channel to switch to
 * @count: the number of TBTT's until the channel switch event
 */
struct ieee80211_channel_switch {
	u64 timestamp;
	bool block_tx;
	struct ieee80211_channel *channel;
	u8 count;
};

828 829 830 831 832 833
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
834
 * @type: type of this virtual interface
835 836
 * @bss_conf: BSS configuration for this interface, either our own
 *	or the BSS we're associated to
837
 * @addr: address of this interface
838 839
 * @p2p: indicates whether this AP or STA interface is a p2p
 *	interface, i.e. a GO or p2p-sta respectively
840 841 842 843
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
844
	enum nl80211_iftype type;
845
	struct ieee80211_bss_conf bss_conf;
846
	u8 addr[ETH_ALEN];
847
	bool p2p;
848 849 850 851
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

Johannes Berg's avatar
Johannes Berg committed
852 853 854
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
855
	return vif->type == NL80211_IFTYPE_MESH_POINT;
Johannes Berg's avatar
Johannes Berg committed
856 857 858 859
#endif
	return false;
}

860 861 862 863 864 865 866 867 868 869 870 871 872 873
/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
874 875
 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
 *	that the key is pairwise rather then a shared key.
876 877 878
 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
 *	CCMP key if it requires CCMP encryption of management frames (MFP) to
 *	be done in software.
879
 */
880 881 882 883
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
884
	IEEE80211_KEY_FLAG_PAIRWISE	= 1<<3,
885
	IEEE80211_KEY_FLAG_SW_MGMT	= 1<<4,
886
};
887

888 889 890 891 892 893 894 895
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
896
 *	encrypted in hardware.
897
 * @cipher: The key's cipher suite selector.
898 899 900
 * @flags: key flags, see &enum ieee80211_key_flags.
 * @keyidx: the key index (0-3)
 * @keylen: key material length
901 902 903 904 905
 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
 * 	data block:
 * 	- Temporal Encryption Key (128 bits)
 * 	- Temporal Authenticator Tx MIC Key (64 bits)
 * 	- Temporal Authenticator Rx MIC Key (64 bits)
906 907
 * @icv_len: The ICV length for this key type
 * @iv_len: The IV length for this key type
908
 */
909
struct ieee80211_key_conf {
910
	u32 cipher;
911 912
	u8 icv_len;
	u8 iv_len;
913
	u8 hw_key_idx;
914 915 916
	u8 flags;
	s8 keyidx;
	u8 keylen;
917 918 919
	u8 key[0];
};

920 921 922 923 924 925 926 927 928
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
929
enum set_key_cmd {
930
	SET_KEY, DISABLE_KEY,
931
};
932

933 934 935 936 937 938 939 940
/**
 * struct ieee80211_sta - station table entry
 *
 * A station table entry represents a station we are possibly
 * communicating with. Since stations are RCU-managed in
 * mac80211, any ieee80211_sta pointer you get access to must
 * either be protected by rcu_read_lock() explicitly or implicitly,
 * or you must take good care to not use such a pointer after a
941
 * call to your sta_remove callback that removed it.
942 943 944
 *
 * @addr: MAC address
 * @aid: AID we assigned to the station if we're an AP
945
 * @supp_rates: Bitmap of supported rates (per band)
Johannes Berg's avatar
Johannes Berg committed
946
 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities
947
 * @wme: indicates whether the STA supports WME. Only valid during AP-mode.
948 949 950 951
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *), size is determined in hw information.
 */
struct ieee80211_sta {
952
	u32 supp_rates[IEEE80211_NUM_BANDS];
953 954
	u8 addr[ETH_ALEN];
	u16 aid;
955
	struct ieee80211_sta_ht_cap ht_cap;
956
	bool wme;
957 958
	u8 uapsd_queues;
	u8 max_sp;
959 960 961 962 963

	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

964 965 966 967
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
968
 * indicates if an associated station made a power state transition.
969
 *
970 971 972
 * @STA_NOTIFY_SLEEP: a station is now sleeping
 * @STA_NOTIFY_AWAKE: a sleeping station woke up
 */
973
enum sta_notify_cmd {
974 975 976
	STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
};

977 978 979 980 981 982 983 984 985
/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
986 987 988 989 990 991 992 993 994 995 996 997 998
 * @IEEE80211_HW_HAS_RATE_CONTROL:
 *	The hardware or firmware includes rate control, and cannot be
 *	controlled by the stack. As such, no rate control algorithm
 *	should be instantiated, and the TX rate reported to userspace
 *	will be taken from the TX status instead of the rate control
 *	algorithm.
 *	Note that this requires that the driver implement a number of
 *	callbacks so it has the correct information, it needs to have
 *	the @set_rts_threshold callback and must look at the BSS config
 *	@use_cts_prot for G/N protection, @use_short_slot for slot
 *	timing in 2.4 GHz and @use_short_preamble for preambles for
 *	CCK frames.
 *
999 1000 1001 1002 1003 1004 1005 1006 1007 1008
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
1009
 *	the driver can fetch them with ieee80211_get_buffered_bc().
1010
 *
1011 1012 1013 1014 1015 1016
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027
 *
 * @IEEE80211_HW_SIGNAL_UNSPEC:
 *	Hardware can provide signal values but we don't know its units. We
 *	expect values between 0 and @max_signal.
 *	If possible please provide dB or dBm instead.
 *
 * @IEEE80211_HW_SIGNAL_DBM:
 *	Hardware gives signal values in dBm, decibel difference from
 *	one milliwatt. This is the preferred method since it is standardized
 *	between different devices. @max_signal does not need to be set.
 *
1028 1029 1030
 * @IEEE80211_HW_SPECTRUM_MGMT:
 * 	Hardware supports spectrum management defined in 802.11h
 * 	Measurement, Channel Switch, Quieting, TPC
Sujith's avatar
Sujith committed
1031 1032 1033
 *
 * @IEEE80211_HW_AMPDU_AGGREGATION:
 *	Hardware supports 11n A-MPDU aggregation.
1034
 *
1035 1036 1037 1038 1039 1040 1041 1042 1043
 * @IEEE80211_HW_SUPPORTS_PS:
 *	Hardware has power save support (i.e. can go to sleep).
 *
 * @IEEE80211_HW_PS_NULLFUNC_STACK:
 *	Hardware requires nullfunc frame handling in stack, implies
 *	stack support for dynamic PS.
 *
 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
 *	Hardware has support for dynamic PS.
1044 1045 1046
 *
 * @IEEE80211_HW_MFP_CAPABLE:
 *	Hardware supports management frame protection (MFP, IEEE 802.11w).
1047 1048 1049 1050
 *
 * @IEEE80211_HW_BEACON_FILTER:
 *	Hardware supports dropping of irrelevant beacon frames to
 *	avoid waking up cpu.
1051 1052 1053 1054 1055 1056 1057 1058 1059 1060