1. 12 Feb, 2016 2 commits
  2. 11 Feb, 2016 3 commits
  3. 10 Feb, 2016 3 commits
  4. 09 Feb, 2016 3 commits
    • Kirk Webb's avatar
      Extend the horrible "non-modular" hack in the Cisco snmpit module. · 0981023d
      Kirk Webb authored
      First, a "bug fix": By coincidence the snmpit Cisco module was able to
      build up the mod/port-to-ifindex mapping on newer switches where
      interface descriptions include a submodule ID (e.g.
      "GigabitEthernet1/0/1" vs. "GigabitEthernet1/1"). However, it was
      actually just grabbing the submodule ID in place of the module ID.  This
      is OK (in some loose sense) for non-modular switches where everything is
      effectivley on the same module. Not good for IOS/NX-OS switches with
      actual modules and submodule identifiers. Things would not have worked
      for these.  As a fix that retains backward compatibility, the Cisco
      snmpit module now correctly extracts the module ID, but subtracts '1'
      from it.  This allows existing installations that have zero-based module
      numbering in their database for non-modular IOS/NX-OS switches with
      submodule IDs to continue to work as is.
      
      The above nonsense is not what I set out to do, however, and the commit
      just gets worse. I extended the hack for non-modular switches with a mix
      of gigabit and ten gigabit to bump any ten gigabit interface port's
      module ID to "1". The existing hack already did this for non-modular
      switches with a mix of fast Ethernet and gigabit.  Absolutely horrific.
      I need a shower.
      0981023d
    • Mike Hibler's avatar
      Fixups for configuring FreeBSD VMs. · 83718697
      Mike Hibler authored
      83718697
    • Mike Hibler's avatar
      Fix setting of console on Xen command lines. · b6b227e3
      Mike Hibler authored
      Did this in the FreeBSD version previously.
      b6b227e3
  5. 08 Feb, 2016 2 commits
  6. 05 Feb, 2016 12 commits
  7. 04 Feb, 2016 1 commit
    • Gary Wong's avatar
      Fix Node::HaveRoutableIPs. · f2e7e6f3
      Gary Wong authored
      It was checking the count of database rows (which would always have
      been 1), not the count of free addresses.
      f2e7e6f3
  8. 03 Feb, 2016 8 commits
  9. 02 Feb, 2016 5 commits
    • Leigh Stoller's avatar
      Merge branch 'master' into current · f31b5a6b
      Leigh Stoller authored
      f31b5a6b
    • Leigh Stoller's avatar
      Add a wrapper script to run Medusa (which does ssh scans looking for bogus · ebe8baab
      Leigh Stoller authored
      accounts/passwords). Thanks to Mike Blodgett for cluing us in to this and
      providing the configuration he was using. This will run from cron a couple
      of times a day. The setup is not quite fully automated yet, need to create
      /usr/local/etc/medusa/{wordlist.txt,userlist.txt} by hand, as well as the
      crontab entry.
      
      We are scanning all local nodes (including VMs) as well as any allocated IP
      addresses in address pools.
      ebe8baab
    • Mike Hibler's avatar
      Merge branch 'master' into current · ee91f51f
      Mike Hibler authored
      ee91f51f
    • Mike Hibler's avatar
      Changes for FreeBSD 10.2 delay node. · 5286f0a5
      Mike Hibler authored
      Minor tweaks so that ipfw/dummynet sets up properly. Allow dynamic
      config (delay_setup) to accept a BW value up to 1Gb (was 100Mb).
      Somewhat dubious: if the incoming interface speed matches the desired
      shaping BW, set the BW to unlimited on the pipe (since the interface
      is already throttling for us).
      
      BEWARE! The fidelity of shaping at over 1Gb (e.g., adding delay to a
      10Gb link) is awful. Even a 10Gb pipe with no delay or loss only achieved
      about 7Gb/sec max. The delay node code needs serious work!
      5286f0a5
    • Mike Hibler's avatar
      Untested support for Linux erase operation. · fd6b84fd
      Mike Hibler authored
      fd6b84fd
  10. 01 Feb, 2016 1 commit