Commit cfdf8259 authored by Leigh Stoller's avatar Leigh Stoller

Change some 192.168s to 10s (for IPBASE change).

parent df490159
......@@ -1317,10 +1317,10 @@
<p>
For instance, let's say I have an experiment that had NodeA and
NodeB connected with a shaped link. The file /etc/hosts on NodeA
would have a line for NodeB, with an address like 192.168.1.3, and
would have a line for NodeB, with an address like 10.1.1.3, and
on NodeB there would be an entry for NodeA with the address
192.168.1.2. These addresses correspond to the delayed link
between them. Any address outside the 192.168.*.* range that you
10.1.1.2. These addresses correspond to the delayed link
between them. Any address outside the 10.1.*.* range that you
didn't configure manually corresponds to an unshaped link.
</p>
......
<!--
EMULAB-COPYRIGHT
Copyright (c) 2000-2002 University of Utah and the Flux Group.
Copyright (c) 2000-2003 University of Utah and the Flux Group.
All rights reserved.
-->
<center>
......@@ -188,7 +188,7 @@ generated under the same subnet, assuming a netmask of <code>255.255.255.0</code
<p>IP address assignment is deterministic and tries to fill lower IP's
first, starting at 2. Except in the partial specification case (see
above), all automatic IP addresses are in the network
<code>192.168.*.*</code>.
<code>10.1.*.*</code>.
<p>If you choose to specify addresses, and don't conform to the same
subnet requirements, you will need to set up the proper routing tables
......
......@@ -60,7 +60,7 @@ issuing commands like:
<pre>
$ns duplex-link $node1 $node2 100Mb 150ms DropTail
tb-set-ip $node1 192.0.0.2
tb-set-ip $node1 10.1.0.2
</pre>
<p>(Note the <code>$</code>'s)
......@@ -113,7 +113,7 @@ two nodes.
<pre>
set link1 [$ns duplex-link $node0 $node1 100Mb 0ms DropTail]
tb-set-link-loss $link1 0.05
tb-set-ip-link $node0 $link1 192.0.0.128
tb-set-ip-link $node0 $link1 10.1.0.128
</pre>
<hr>
......@@ -173,7 +173,7 @@ will be automatically generated under the same subnet.
<p>IP address assignment is deterministic and tries to fill lower IP's
first, starting at 2. Except in the partial specification case (see
above), all automatic IP addresses are in the network
<code>192.168</code>.
<code>10</code>.
<h4>tb-set-ip</h4>
......
......@@ -101,9 +101,9 @@ For FreeBSD, this is done with:
#!/bin/sh
if [ `uname` = "FreeBSD" ]
then
sudo route add -net 192.168.0.0 -netmask 255.255.0.0 myrouter
sudo route add -net 10.1.0.0 -netmask 255.255.0.0 myrouter
else
sudo route add -net 192.168.0.0 netmask 255.255.0.0 gw myrouter
sudo route add -net 10.1.0.0 netmask 255.255.0.0 gw myrouter
fi
exit 0
</pre></code>
......
......@@ -280,18 +280,18 @@ similar to this:
nodeA pc600 RHL73-STD pc13
Virtual Lan/Link Info:
ID Member IP Delay BW (Kbs) Loss Rate
ID Member IP/Mask Delay BW (Kbs) Loss Rate
--------------- --------------- --------------- --------- --------- ---------
lan0 nodeC:0 192.168.2.3 0.00 100000 0.000
0.00 100000 0.000
lan0 nodeB:1 192.168.2.4 0.00 100000 0.000
0.00 100000 0.000
lan0 nodeD:0 192.168.2.2 0.00 100000 0.000
0.00 100000 0.000
link0 nodeB:0 192.168.1.2 25.00 30000 0.005
25.00 30000 0.005
link0 nodeA:0 192.168.1.3 25.00 30000 0.005
25.00 30000 0.005
lan0 nodeC:0 10.1.2.3 0.00 100000 0.000
255.255.255.0 0.00 100000 0.000
lan0 nodeB:1 10.1.2.4 0.00 100000 0.000
255.255.255.0 0.00 100000 0.000
lan0 nodeD:0 10.1.2.2 0.00 100000 0.000
255.255.255.0 0.00 100000 0.000
link0 nodeB:0 10.1.1.2 25.00 30000 0.005
255.255.255.0 25.00 30000 0.005
link0 nodeA:0 10.1.1.3 25.00 30000 0.005
255.255.255.0 25.00 30000 0.005
Physical Lan/Link Info:
ID Member Delay Node Delay BW (Kbs) PLR Pipe
......@@ -302,10 +302,10 @@ similar to this:
Route List:
Node Interface Dest Nexthop Type Cost
--------------- --------------- --------------- --------------- ----- ----
nodeA 192.168.1.3 192.168.2.4 192.168.1.2 host 0
nodeA 192.168.1.3 192.168.2.0 192.168.1.2 net 0
nodeC 192.168.2.3 192.168.1.0 192.168.2.4 net 0
nodeD 192.168.2.2 192.168.1.0 192.168.2.4 net 0
nodeA 10.1.1.3 10.1.2.4 10.1.1.2 host 0
nodeA 10.1.1.3 10.1.2.0 10.1.1.2 net 0
nodeC 10.1.2.3 10.1.1.0 10.1.2.4 net 0
nodeD 10.1.2.2 10.1.1.0 10.1.2.4 net 0
</code></pre>
<p>
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment